How to Build a Homemade Solar Panel From Scratch

How to a build homemade solar panel from scratch. DIY Solar Panel 100Watts. learn-share.ne... Which solar cells to choose? Polycrystalline vs Monocrystalline? Everything you should know to build a 100 watts solar panel at home. 💟 Subscribe goo.gl/zp1F6R
➥ Solar Panel Kit amzn.to/2wY5ILJ
➥ Best Amazon Today's Deals amzn.to/2MHmwM2
📝 To build a 100W solar panel you need:
➥ 6x6 solar cells kit: amzn.to/2wXQ03g
2mm tabbing wire (pre solder cm8nated).
5mm tabbing wire (buss wire).
Solder Wire. (Used to tin the solder iron, also used to solder the tab cells on the buss wire).
Flux Pen. Prevents beading of the solder.
Strapping Tape (sure tape).
Regular tape.
(useful to hold the solar cells).
Sillicone Paste-like seal (UV christaline).
➥ Clear Epoxy Resin 40 ounces / 1Kg. + Epoxy Hardener 2 Epoxy resin x 1 Hardener. amzn.to/2gUxFK9
Untabbed Cells
Solar Panel Aluminium Frame
➥ 6 or 8 gauge AWG Solar Wire (10 gauge 30Amps, 8 gauge 40Amps, 6 gauge 55Amps) amzn.to/2wqPtoS
➥ Solder Iron 60/80W amzn.to/2eqSpbx
➥ Multimeter. (Volts and Amps). amzn.to/2eqVNmN
➥ 20 Amps PWM Charge controller amzn.to/2vRNGFR
➥ 600W DC/AC Inverter amzn.to/2wqwrz3
➥ 12V 48Ah Depp Cycle Battery amzn.to/2vRdXV2
12V 90Ah Depp Cycle Battery amzn.to/2vz1AS3
12V 120Ah Depp Cycle Battery amzn.to/2iOfgCN
✦ Polycrystalline Solar Cells
+ The process used to make polycrystalline silicon is simpler and cost less.
+ Polycrystalline solar panels tend to have slightly lower heat tolerance than monocrystalline solar panels.
- The efficiency of polycrystalline-based solar panels is 14-16%.
- Lower space-efficiency. You need to cover more surface to output the same electrical power as Monocrystalline cells.
✦ Monocrystalline Solar Cells
+ Monocrystalline solar cells have the highest efficiency rates.
+ Monocrystalline silicon solar cells are space-efficient.
+ Monocrystalline cells have a long lifespan.
+ Monocrystalline solar panels tend to be more efficient in warm weather.
- Mono-crystalline solar panels are the most expensive.
💟 Thanks for watching, and remember Subscribe goo.gl/KLeC2V if you haven't already.
🛍 Amazon Today's Deals amzn.to/2MHmwM2
🛍 Amazon Coupons!! amzn.to/43vwYwN
Be the first to know, Subscribe our newsletter ➥ learn-share.net...
Follow us on Amazon ➥ www.amazon.com...
This Channel is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.
#solarpanel #diysolarpanel #solarenergy #solarpower #homema #diy #diysolar #offgrid #solarpanels #homemadesolarpanel

[@Bikesworld7.0]

Excellent work thumbs up for your Great work

[@learnshare]

Thank you Bikewotld!

[@dieudonnelomamba2068]

Cool. This video is very informative. Thank you. But I did not find part 2 of the video.

[@dieudonnelomamba2068]

Thanks. Keep up the the good work. Did you post part 2 yet?

[@MR-ub6sq]

11:59 I don't see what the problem is if there are small air bubbles in the resin, because the resin only spreads to the back of the cells. If the resin got between the negative surface of the cells and the glass, then it would obviously be important to have the resin air-free for use. There could also be an idea because this way the surface of the cells would turn black - which is better in terms of yield than blue. Between 13:04 and 13:37 I don't understand what the problem is between these two dishes. 15:37 L-shaped aluminum is the wrong choice. It must definitely be U-shaped so that the profile also has a stiffening corner at the back. Absolutely! The L-profile is not rigid enough and may detach, and it does not protect the structure sufficiently. In addition, I notice that in this case the author has chosen the worst possible L-profile - its two sides are COMPLETELY different widths. It is best to choose one with both sides of 25 mm or preferably 30 mm. And practically THREE pages - not two! 15:42 Aluminum frames should not be replaced with wood if you want the panel to be long-lasting. If the durability of the panel doesn't matter, why do you even use glass and frames? You could use some moisture-absorbing board, make two holes in it for the power wires. Brush the resin over the surface of the board, place the rows of cells on it and finally brush the same resin over the negative surfaces of the cells as well. This last layer of resin would probably turn the blue surface into black, which is better for power generation. 18:53 When drilling metal, use oil between the blade and the surface. Any running oil will do. This way, drilling is faster, more precise and the blade stays sharp. In addition, the chip that comes off does not fly around but remains in the oil and is therefore easy to wipe off at the end. 20:46 These brackets placed to support the "glass" are not only completely useless - but also harmful. Due to the environmental conditions, they may cause stresses on the edges of the cells and cause cracks. The frames are attached to the glass with silicone and the fasteners in the corners of the frame are sufficient.

[@bete.s.22]

Nice! 😊

[@plugedchannel]

Great job!!

[@22446678]

Thanks for the video. Just a note to myself: how much time does it take for one to produce this given we have all the material ready?

[@jessehavok4181]

I was thinking about doing this until I realized that the cost is much more when building your own panels. You can get panels for as low as 50 cents per watt.

[@learnshare]

That's not the purpose of the video.

[@evilleprichaun7096]

where do you get the tempered glass cheap

[@learnshare]

They aren't cheap. Try local store in tour region, or go with a Mon tempered glass.