How To Build a Ported SubWoofer Enclosure for a Single 10 inch | Specs Included

After designing a ported box for my single Rockford Fosgate P3 10 inch subwoofer, it's finally time to cut out the parts and put it together! I used a table saw to carefully cut out all the parts from 3/4in MDF (Medium Density fiberboard). I cut out the subwoofer hole with a router and special guide. Then I assembled it with, drill, impact driver, liquid nails, silicone caulking. and wood screws. Thanks for Watching, have fun, and be safe!
Disclaimer: Power tools can be dangerous. be sure to read and follow all safety precautions outlined in your specific Power tool instructions. I take no responsibility for your actions.
Cut List for this 10 inch ported subwoofer enclosure design (3/4in MDF):
Front: 16.5" X 11.5"
Back: 18.5" X 11.5"
Side: 14" X 11.5"
Side: 14" X 11.5"
Top: 14" X 20"
Bottom: 14" X 20"
Big Port: 14.5" X 11.5"
Small Port: 9.75" X 11.5"
(measurements in inches)
Full video series on the way!
You can find most of these supplies and tools at your local Hardware store. Here are also some links to similar things I was using to build this enclosure:
6x2" Flat Head Phillips Screws: amzn.to/2VB22to (paid link)
Caulking Gun: amzn.to/3bk8Lyv (paid link)
Silicone Sealant Caulk, Black: amzn.to/2zaLfpr (paid link)
All Surface Liquid Nails: amzn.to/34HUtVV (paid link)
DEWALT Cordless Drill & Impact Driver Kit: amzn.to/2Kb8CkU (paid link)
Screwdriver Bit Set / Drill Bit Set: amzn.to/2ypGsQm (paid link)
Router: amzn.to/2wO1vM9 (paid link)
1/4" Router bit: amzn.to/2xGSlSb (paid link)
Router Circle cutting guide: amzn.to/2RMpF13 (paid link)
Hole Saw Set: amzn.to/3eFx7ou (paid link)
Bar clamps: amzn.to/2XJ3TPm (paid link)
Rafter square: amzn.to/2XJTrae (paid link)
Terminal Cup: amzn.to/2KfFfhq (paid link)
Find this Subwoofer, Amplifier, and wiring kit here:
Rockford Fosgate P3D4-10 Punch Subwoofer: amzn.to/376PE7T (paid link)
Rockford Fosgate R500X1D Prime 1-Channel Class D Amplifier amzn.to/36Y76vj (paid link)
InstallGear 4 Gauge Complete Amp wiring Kit: amzn.to/31ulNVX (paid link)
(I may get commissions for purchases made through links with "paid link" next to them)
music:
www.epidemicso...

[@4WheelKid]

Cut List for this 10 inch ported subwoofer enclosure design (3/4in MDF): Front: 16.5" X 11.5" Back: 18.5" X 11.5" Side: 14" X 11.5" Side: 14" X 11.5" Top: 14" X 20" Bottom: 14" X 20" Big Port: 14.5" X 11.5" Small Port: 9.75" X 11.5" (measurements in inches) You can find most of these supplies and tools at your local Hardware store. Here are also some links to similar things I was using to build this enclosure: # 6x2" Flat Head Phillips Screws: amzn.to/2VB22to (paid link) Caulking Gun: amzn.to/3bk8Lyv (paid link) Silicone Sealant Caulk, Black: amzn.to/2zaLfpr (paid link) All Surface Liquid Nails: amzn.to/34HUtVV (paid link) DEWALT Cordless Drill & Impact Driver Kit: amzn.to/2Kb8CkU (paid link) Screwdriver Bit Set / Drill Bit Set: amzn.to/2ypGsQm (paid link) Router: amzn.to/2wO1vM9 (paid link) 1/4" Router bit: amzn.to/2xGSlSb (paid link) Router Circle cutting guide: amzn.to/2RMpF13 (paid link) Hole Saw Set: amzn.to/3eFx7ou (paid link) Bar clamps: amzn.to/2XJ3TPm (paid link) Rafter square: amzn.to/2XJTrae (paid link) Terminal Cup: amzn.to/2KfFfhq (paid link) Find this Subwoofer, Amplifier, and wiring kit here: Rockford Fosgate P3D4-10 Punch Subwoofer: amzn.to/376PE7T (paid link) Rockford Fosgate R500X1D Prime 1-Channel Class D Amplifier amzn.to/36Y76vj (paid link) InstallGear 4 Gauge Complete Amp wiring Kit: amzn.to/31ulNVX (paid link) (I may get commissions for purchases made through links with "paid link" next to them)

[@timothyblaze4556]

I'm buliding a ported box for 2 of these p3s 10 inch subs... so would I just double this box size or how would I go about it??? Please please help... ill will pay if needed thank you buddy I appreciate it.

[@cottonnelson7860]

Hell yea.. thanks man. Awesome video

[@DJSHAHILMUKHIJAMSHEDPUR]

Bro please give the measurements of front bass cabinet for single10inch 100w woofer ..please give me quick response

[@daw5562]

I did these exact measurements and my box turned out completely to small and barley fits the 10 inch sub inside

[@peterkunka2694]

Man, the memories from the late 80's building sub boxes running Rockford Fosgate amps and Cerwin Vega subwoofers. We used to spend Saturday's building them and trying different sizes to see how it affected the sound and punch. I don't want to take up cargo space now in my Jeep (I camp a lot), but building a system for the house would be a lot of fun to do. Got me thinking and smiling cranking up the old 80's hair bands again! Peace! Pete in AZ

[@4WheelKid]

I bet that was a cool time to be alive! I hear that, might look into an under seat subwoofer. I installed it in my 4runner to save space for camping and have loved it ever since, installing another in my van soon. kzbin.info/www/bejne/bKStoWqOi9F1htk best of luck! a house subwoofer would be cool for sure

[@peterkunka2694]

@@4WheelKid It was definitely a good time for music. All we had back then was the radio and we couldn't wait to hear albums being released and played on the air by our favorite DJ's (Dave Pratt on 98KUPD in Phoenix, AZ, for example). I'm going to keep the house system idea for when I get a man cave soon (40' conex box on land near the main house). I have watched a lot of your TW200 videos and will be checking out the van build!

[@notme7970]

I’m glad to know they’ll fit in my 4 runner ;)

[@4WheelKid]

it will for sure, I just have an under seat sub in my 4runner, this one went in my bmw

[@Jack-mv3sx]

Damn this video rocks, easily the best on KZbin. Makes me wish I had a P3 so I could just copy you lol!

[@4WheelKid]

hey thanks! glad you enjoy it, the p3 is a nice subwoofer haha, any subwoofer is better than none

[@streetangel6783]

Great video brother...very very very well done 9/10💯💯🤝

[@4WheelKid]

hey thanks! glad to hear you enjoyed it

[@33lowdown]

Enjoyed video alot, very informative bro...

[@4WheelKid]

Glad you enjoyed!!

[@alexislazarte1539]

Hi, I have a 10" 600watts subwoofer..is it okay if I ask a help from you. I wanted to do DIY, can you help me with a ported box dimension?

[@4WheelKid]

Dimensions in the description

[@cjon24s69]

Nuce job but I dont recommmend using liquid nails adhesive, use wood glue its so much stronger and will last alot longer than any adhesive

[@4WheelKid]

thanks! yeah I have heard it both ways

[@TrollsAreUs1320]

Actually wood glue would be worse, it’s hard as wood so it can crack where as liquid nails or all purpose loctite is better because it’s more elastic and takes longer to get as hard as wood glue, so it would be harder for the subwoofer to vibrate it apart

[@cjon24s69]

@@TrollsAreUs1320 liquid nails is garbage for building boxes, wood glue is much stronger and wood glue will not crack. Any flex in the joints (youll have much more flex with loctite) youll lose output. Never use liquid nails to build a sub box.

[@TrollsAreUs1320]

I promise you from experience, wood glue over time will crack it gets too hard, otherwise he would use that only, that’s why he uses the liquid nails as a sealant not as to hold the box together. He’s using screws to keep it tight and the LN as sealer

[@cjon24s69]

@@TrollsAreUs1320 If you build enclosures like me and take the time to get straight cuts there is absolutely no need for liquid nails or any sealant, the glue will be sandwiched between the joining surfaces and there will be no gap. I still have my first enclosure I built when I was 15, going on 6 years now sitting in my garage in all climates. And Ive never ever seen or heard of wood glue cracking. You must have used some terrible glue. If you had proper cure time and clamp force, wood will always crack before the glue.

[@scottcooksey5284]

Nice job,, you do however need to round over all interior edges of your port.

[@4WheelKid]

thanks! not a bad idea. a trim router will do the trick for next time

[@raymondhernandez304]

Can you make one for a wedged box? One for a single cab Silverado or any truck? Thank you!

[@4WheelKid]

it's possible, I made one for a truck a while back

[@timothyblaze4556]

Hello, my friend. Just wanna say this is a great video to learn some things on... but I have two of these subs... so would I just double the measurements??? Please help.. I appreciate it buddy, thank you!!!

[@RobHTech]

nice vid. I suppose you could always use two different size boards, 1/2" X baffle or 3/4" X baffle, then 3/4" for the sides, or something like that, esp. if space is limited. Does 3M 77 or another 3m spray or gorilla glue spray work for carpeting a fiberglass box?

[@4WheelKid]

I bet you could indeed. might be a bit more complicated but doable not sure, never tried a fiberglass box before

[@salvatoreiannone4130]

Nice Job, what model of sub Woofer use in these box?

[@4WheelKid]

it's a rockford fosgate p3 10in

[@sujeevicf3864]

Wheather it is suitable for home or not?

[@4WheelKid]

will work just fine

[@shadowmichellemartinson4402]

Would you use 1/2 or 3/4 in for a 10 in sub

[@4WheelKid]

I used 3/4 on this one by you should be able to get away with 1/2

[@phreaktor]

What is the port tuned for?

[@4WheelKid]

Tuned to have free flowing air at a certain frequency.

[@phreaktor]

@@4WheelKid I mean what frequency. I am in the process of building it off this video and I want to tune for around 40Hz

[@travisgulley2652]

Quick question will the subwoofer enclosure itself flex from the vibration

[@4WheelKid]

not enough to actually see

[@scottiffanimccord1509]

Thanks bud.

[@4WheelKid]

No problem 👍

[@firmansyah4556]

ask for advice from friends, if the size for Rockford P3D4 12inc,

[@4WheelKid]

😅

[@harrison790]

What’s the depth of the sub?

[@4WheelKid]

6.66 in. (169.3 mm)

[@mosessanchez2817]

What’s the HZ for this 10” box?

[@4WheelKid]

I talk about it in this vid kzbin.info/www/bejne/oqLFoK2Amc6aacU

[@faded_ruko]

the bit was “dull” because you used the wrong type of bit..that bit is for steel

[@4WheelKid]

thanks for letting me know

[@romainepope]

How much cu ft is this box ?

[@4WheelKid]

1.54 cu ft

[@bryanroupe8646]

Just what I was about to ask. Thanks my man.

[@ogcanada9871]

I wish someone would tell the guy how dangerous mdf is for your lungs. A dust mask will not protect you. When punching holes in mdf if you are burning board and inhaling dust with fumes with no respiratory protection this is how you get cancer or worse.. When handling clean mdf with bare hands you need to wash hands extremely well after because it contains formaldehyde

[@4WheelKid]

thanks, best to be safe, I also don't do this everyday

[@durgaprasadbeera4788]

Use 850 watt dainty subwoofer bro

[@4WheelKid]

already got puch p3 installed

[@SickF-pk8fu]

How much do I need to leave the port area apart??

[@4WheelKid]

I designed mine so the port is 2in wide

[@SickF-pk8fu]

Thanks and I already cut all the pieces and I wanted to ask how did you like the box ? Did it work good thanks

[@4WheelKid]

I love it! Works great, still gotta edit and upload the final install and test video

[@SickF-pk8fu]

bassisgood great I’ll be waiting and it’s a pretty good box in my opinion thanks

[@jimijesus7869]

yea love it bippy trippy dippy boom dap excuse me while i hit this. bam dam slam m back lets do this box builder here, i say lets have a build off? u scared? prolly not. cam cam sham sham shy me. poop

[@4WheelKid]

Based

[@jeffreywolf5235]

Too funny you're using a router to cut the woofer out and a dull drill bit to pre-drill the holes.. proper and Sharp Tools make all the difference

[@4WheelKid]

yeah haha, just used what I had laying around. I need to get one of those bit sharpeners

[@jeffreywolf5235]

@@4WheelKid I've got one they kind of suck. You're better off just buying a bulk small drill bits at the generally one or two sizes that you used most of the time