How To Build A SOFT WASH Metering Valve - DIY Proportioner

[@AllAboutPressureWashing]

Parts List- you can also find a lot of these parts locally at industrial supply stores: www.amazon.com/shop/foreverselfemployed

[@parmerrobert]

did you add the instructions on how to set the valves ?

[@dustinjohnson2116]

The parts are not pulling up.

[@AllAboutPressureWashing]

@@parmerrobertthis video is the explanation

[@AllAboutPressureWashing]

@@dustinjohnson2116the link was dead

[@timsalameh]

Hey Mike, i wanted to take the time to thank you for sharing so much knowledge especially to those looking to start in the business. You're a huge asset to the service business community and we appreciate the knowledge sharing

[@AllAboutPressureWashing]

+T S thank you for the kind words- I’m glad it helps

[@nick32141]

That’s the best explanation that I’ve seen about making your own proportioner. Excellent video. Thanks

[@AllAboutPressureWashing]

+Omega1 thank you very much! All the links to what you need are in the description.

[@JayTFoster]

Remember! All of your input or inflow 1/2 hoses must all be the same length. So measure from your proportioner to your furtherest tank. Take that length and cut 2 more hoses the same length and attach. Helpful tip to help your valve work at peek performance

[@hashtagscooterswagyoloswag7828]

Should all of the hoses be 1/2 inch for a 7 gpm system?

[@Average_American0]

Ty

[@ChadAmI80]

Thanks for the tip. This is something I had not even considered, but makes so much sense.

[@rickyhuisman6911]

Building my first Softwash setup. This proportioner is an easy build. Thanks Mike!

[@SalishSavage-1]

You are the man bro you make the best videos by far. Everyone else is so fake or more jyst out for them selves. You like helping people and I respect that

[@AllAboutPressureWashing]

Thanks man- I appreciate that.

[@PowermountPowerWashing]

So much cheaper than our current "proportioner in a box". The trouble we have experienced with manufactured proportioners is repair time. If we get a leaking check valve or anything that could be a quick swap-out, the entire unit has to be disassembled to access it. Moving forward we build our own. Thanks Mike, for all of the great information you share on here.

[@AllAboutPressureWashing]

That can be a problem - but if you use quality parts, don't overtighten and use adequate Teflon sealant, you should be good to go

[@AllAboutPressureWashing]

Just got a text from someone asking about the surfactants we use. It really depends on the surface being cleaned and there are so many companies out there selling stuff that is worthless, we use Southeast Softwash detergents.

[@onlyeasydaywasyesterday]

Hey Mike I didn't see the chemical mixing ratios in relation to the dial settings in the description

[@OlyBoys23]

straight to the point, great content. Love the links with parts and names of the equipment. When I first started my business this was the most difficult part. Keep up the good info !

[@AllAboutPressureWashing]

Thank you Dennis, make sure you hit that subscribe button!

[@zoemaravilla2538]

I just started my little business and batch mix. I find this proportioner thing to be complicated

[@jonboysprowash7845]

Really simple video. I’m going to build one and use the Pentair valves not over tighten and see how it lasts. Thanks for the video and links

[@AllAboutPressureWashing]

Thx for watching

[@JimmySutton-ip1bx]

Very good info because I like to know the why and how of everything.

[@ronjclm8590]

A mixing valve system CAN be used with a gas roof pump according to Leon Johns. He just put about 20 feet of hose under his trailer and uses it to recirculate and cool the pump when he's off the trigger.

[@AllAboutPressureWashing]

I have seen a couple guys do it,

[@hanskonrad5850]

mike thankyou for breaking that down man , makes the big picture very clear on the flow of the system . im going to depot now to get this together ! boom!

[@AllAboutPressureWashing]

Depot is not going to have the check valves or metering valves. I would use all the links for the parts I provided - will make it much easier for you.

[@AllAboutPressureWashing]

And thank you for watchint!

[@hanskonrad5850]

@@AllAboutPressureWashing Mike thanks for looking out . Where are the links .

[@AllAboutPressureWashing]

In the description - link to metering valve

[@AllAboutPressureWashing]

www.cleansavannah.com/softwash-metering-mix-ratio-chart

[@thomasmitchell3987]

Hey Mike great video and very helpful. Have a question I cant find the link to the mixing chart.

[@577buttfan]

So half of the dial is 50% SH.

[@gregswanner4600]

Very good presentation, best one I've watched

[@AllAboutPressureWashing]

Thank you Greg, I appreciate the feedback. I hope you subscribe, also check out our new satisfying cleaning video.

[@AllAboutPressureWashing]

+Greg Swanner Thanks for the comment - enjoy and subscribe!

[@rmass68]

Hey Mike. Can you send me a material list for this system. I can seem to get into the page that has it. The chart would be helpful to. Thxs! Ron

[@groundrodshorts]

Great video! I just went to Amazon and bought most parts. One or 2 is out of stock and a few of the things were outrageous in pricing. Like 24 bucks for a nipple, I found through another seller for like 6 bucks. The pentair metering valves we're 50 from this link but 30 through another vendor. Price increase is probably due to the "plastic shortage" from covid.. All in I was at like $175-180. I bought a couple of the extra barbed fittings just in case I brake one. Just a heads up. I really appreciate the content! I'm excited about getting into roof washing. I'm a Roof Maxx dealer so I'm hoping this will mesh nicely!

[@AllAboutPressureWashing]

Nice! The 1/4” nipples have a tendency to break so good calll!

[@cfmill74]

GS4Clagg, where did you find the metering valves cheaper? Thank you!

[@juans-life]

This is my first year running a proportioner. Just waiting for it to warm up to test it out and find good ratios for the valves. Mainly run vinyl siding and use to batch mixing so have to figure out ratios

[@EazzyBeezie]

This is awesome. I’m buying this week because I’m tired of batch mixing

[@AllAboutPressureWashing]

💯

[@hsilva3213]

Could you make a video explaining your metering chart with this setup. As far as what % would be actually coming out at the end.

[@AllAboutPressureWashing]

Great Idea.

[@erikrose7041]

Exactly, that's my main concern about building myself. Don't know percentages

[@MrHRDGAMER]

Did this video ever come out?

[@577buttfan]

Koty from southeast has one.

[@rmass68]

It says your storefront is inactive on Amazon. Where can I go to purchase these items?

[@robertgreen241]

Ordered the parts for a proportioner build of off your link. Thank you very much for the info big help.

[@AllAboutPressureWashing]

+Robert Green awesome! Good luck

[@robertgreen241]

@@AllAboutPressureWashing yes sir. Thank you

[@dustinjohnson2116]

There not pulling up when I click on link

[@shaunharden4879]

Hey, I’m a little late to the game but if I could please have that chemical chart. Great video by the way!

[@danielcwiok2631]

Great vid. However I have a comet p40 gas powered 11gpm. I’m currently building this proportioner system, but where does your bypass go? Thanks in advance.

[@AllAboutPressureWashing]

I have never built a gas powered proportioner, I know that they can be done, I am sure there are a couple videos out there on it. Sorry I couldn't help

[@danielcwiok2631]

No prob! I figured it out. Great channel btw. Cheers

[@streetpreacher7176]

You’re the man!! As always Thankyou for all your help for us newbies!

[@AllAboutPressureWashing]

+StreetPreacher717 my pleasure

[@vannmorala537]

Great video, looks like I’m going with this proportioner DIY set up but what hoses are you using to connect to the proportioner? How would you connect them?

[@AllAboutPressureWashing]

+Vann Morala braided nylon hose - hose clamps

[@vannmorala537]

Just sent my order... about $270. Can't wait to get everything set up, thank you!

[@MrNick-]

Quick question! Have you ever added a two way underneath the check valve on the SH side so you can add your SH hose plus a H2O hose... in order to flush the check valve and meter valve with fresh water? I hear guys say it’s good to do but haven’t seen anybody build it in a way that you would be able to. What are your thoughts? btw this is a GREAT video!!

[@AllAboutPressureWashing]

Mr. Nick Thanks. I do not have this plumbed directly into the tanks, I have drop lines with stainless filters so I am able to pull out the The line that goes into the SH and drop it in the H2O tank to flush which illuminates the need for another valve, decreasing cost and possible malfunction

[@MrNick-]

CleanSavannah - Sales, Marketing & Tech Tips that’s a smart move, I like it!

[@cutter5767]

thanks for asking this question!

[@gcsoftwashllc]

Hello and thank you for doing this! Quick question, where is the link for the ratio chart?

[@gadsdenconsulting7126]

In was wondering the same thing...

[@rickthemagicguy6075]

Hi Mike. I clicked on the link, it took me to Amazon but said your store is no longer available. Do you have the parts list you could send? Respectfully, Rick

[@AllAboutPressureWashing]

𝐄𝐪𝐮𝐢𝐩𝐦𝐞𝐧𝐭 & 𝐏𝐚𝐫𝐭𝐬 (𝐀𝐦𝐚𝐳𝐨𝐧): www.amazon.com/shop/foreverselfemployed

[@robertonodarse7627]

Thanks for all your videos. Just one question. Where I can find that long tip the you use. Thank in advance.

[@bryanfehse6546]

Could you use regular clear pvc cement?

[@AllAboutPressureWashing]

No

[@brevenlangley5726]

Great video, but you have a smaller barb fitting in the center, could you explain why that is? I’m assembling mine right now and am just wondering why.

[@AllAboutPressureWashing]

Yes for a surfactant

[@brevenlangley5726]

@@AllAboutPressureWashing awesome, thanks

[@johnwitt586]

I just came across your channel and subscribed! Awesome video! Thank you for sharing!

[@AllAboutPressureWashing]

John W Glad you found us!

[@AllAboutPressureWashing]

Thanks man

[@AllAboutPressureWashing]

+John W thx

[@AllAboutPressureWashing]

+John W thx

[@AllAboutPressureWashing]

+John W thanks

[@dago5252]

Awesome & to the point video. Being new to the business, the ratio chart is great. How would you calculate the amount of SH hitting the surface when using 10% SH?

[@AllAboutPressureWashing]

Thanks for the feedback and good luck with the new business. If you look at the chart and you had an undiluted tank of 10% SH and set the valve dial to "1" and also on "1" for your H2O, you would be diluting it by 50%. If you wanted to increase the amount of SH for a stronger/hotter mix, you would turn the dial up on the SH side - so put the SH dial at "2" and leave the H2O dial at "1" and you would have a 67% SH : 33% H2O ratio.

[@hsilva3213]

So if both set to 1 your mix would be 5% hot using 10%SH. Ove been told to always run H2O valve wide open. So I'm sure if they are both wide open you will still achieve 5% close SH valve to maybe half and you would have a 2.5% mix??? Just going off valve position not really numbers.

[@9ineonetwo996]

Great video and explanation

[@AllAboutPressureWashing]

Thx

[@ReeferLife]

Getting ready to build the proportioner and in your video, you mentioned a chart of ratios for the control valves and mixture % I may have overlooked it and was wonder if you could share the link with me?

[@577buttfan]

Yeah it would be nice to know where to set the valves for a general mix?

[@properpreparation3213]

Very helpful! Thanks...one thing though can you check the Amazon link for the (2) Banjo SL050-90 Polypropylene Pipe Fitting, 90 Degree Street Elbow, Schedule 80, 1/2" NPT Female x NPT Male. These may be the wrong size. All my fittings came in today and those were off...Too Big. Everything else fit. Thinking either the selected link is wrong or i was sent the wrong size.

[@AllAboutPressureWashing]

Man, I hope it wasn’t on my end. I will double check. Thankfully, Amazon is great about returns.

[@glennmcfarland1550]

Hi Mike, Great Video, thanks. I followed the link for the parts but could not find them? It takes me to the page but couldn't specifically find all of the parts. Appreciate any help

[@graceunderpressure]

Great video Mike but, why have you moved to gas only? What's the main advantage(s) of gas over air? Thanks

[@AllAboutPressureWashing]

Great Question and honestly it is just a personal choice, I know lots of guys swear by whatever system they are running. I have had 12v pumps that have a limited life span, blow fuses and have a hard time priming, they are effective and work fine but I wanted something a little more reliable. I went to air diaphragm pumps for a very short time, work well but again there are more "moving parts" with a compressor. Finally have moved to the 11.4 GPM @ 290 PSI, Honda GX200, with AR45LFP pump. This thing is a beast, only down side is having to batch mix but that really isn't that big of a deal.

[@graceunderpressure]

@@AllAboutPressureWashing Hey Mike, I really appreciate you explaining your reason for the switch. That pump really does look like a beast! Were you able to buy it as a whole unit or do you have to buy the pump seperate from the engine and do it yourself?

[@AllAboutPressureWashing]

You can buy the entire thing as a mini skid, lots of distributors have them, this specific one came from L And h industrial in Savannah Georgia.

[@graceunderpressure]

@@AllAboutPressureWashing Thanks for letting me know. After some research I actually located it exactly where you suggested. Hoping to have it sometime next week. Hopefully it won't be too bad getting it operational and making $$$ Thanks again for the info!

[@AllAboutPressureWashing]

Grace Under Pressure That is great, please let us know how it’s going, don’t forget to subscribe for more info.

[@MrHardkor23]

do you have a shareable link or file for the proportional chart, i read somewhere in the comments its not available online any longer.... thank you in advance for your help!!

[@AllAboutPressureWashing]

No, sorry

[@alreadydead2000]

Looks like Mike been spending more time with the dumbbells in his hand instead of a wand! 💪

[@jonathanhartman8265]

i did not see the link for the ratio chart, was curious if i could still get that. Thanks!

[@stevendean-w8w]

Thank's Mike, very helpful.

[@AllAboutPressureWashing]

👊🏻

[@mattrobinson1969]

Can't find your link for Ratio Chart.

[@CW_US]

I didn't see the check valve's in the parts list?

[@AllAboutPressureWashing]

My bad!! Inline Poppet Check Valve 685 Series PP 1/2 FPT - BUNA www.amazon.com/gp/product/B005VPM2AA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

[@scuffedvegeta2756]

can you do a video on how you hook this up with hoses and your tank set up ect?

[@AllAboutPressureWashing]

Already did

[@MoneyGrabber72]

Mike is their a reason you have gotten away from the pumps and going to gas thanks

[@ews-texas5258]

Sorry for my ignorance on this. Can you tell me the difference in the control valve and the metering valve on the parts list

[@AllAboutPressureWashing]

The one with the red handle is an upgraded version.

[@ews-texas5258]

@@AllAboutPressureWashing thank you

[@AllAboutPressureWashing]

👍🏻

[@habifrancis4413]

Where is the part list and the mix ratio chart? Thank you

[@nickdill185]

I noticed in your Amazon link, there is 3 ball valves needed but I do not see them in this video. Also they are 125 each so the new total was like 600

[@AllAboutPressureWashing]

+Nick Dill there two different types - you only need three. The one with the red handle is an upgraded version - the one with the white handle is what was in the video

[@ajdahun]

Why did you switch from electric pumps/ proportioning valves to a gas powered pump? And did you go back to batch mixing due to using a gas powered pump?

[@AllAboutPressureWashing]

+ajdahun We went from gas powered to 12 V. We do not use gas powered pumps. anymore. Just 12 V and proportioners

[@ajdahun]

@@AllAboutPressureWashing gotcha, musta heard it wrong

[@JarelW]

I using this system with a 3way ball valve. I just recently hooked up the soap line that feeds to the down stream as well to the 12v. Iv noticed sometimes( very rare) I can get soap to pull in the downstream, but never a issue with the 12v. Is this what you was talking about at the beginning of the video? I’m a little confused on the proportioner I thought I’d be able to us if downstreaming?

[@AllAboutPressureWashing]

+Jarel Wilkins you can use a Proportioner with a downstream - and I don't really see any value there. Because with down streaming, the max you're probably gonna be able to get his about a 1.5% mix. Check out the how to wash course - it will really help

[@JarelW]

@@AllAboutPressureWashing ok thanks.

[@dcsc4895]

how do these hold up ? do they last if you are careful?

[@ALLENBARNES-q1z]

dont see the ratio chart.. any assistance? thanks AL

[@DoubleRFarmsAL]

I can't find a video that shows how to use the metering/proportional system to get different ratios. Any input to get a starting place is appreciated.

[@jacobscott833]

Don’t know if you’ll see this but why do you put the check valve on one side of the valve instead of protecting the valve instead? Curious if there was a method to the madness lol

[@acmext]

can we use a proportioner in our gas machines?

[@AllAboutPressureWashing]

Yes

[@acmext]

@@AllAboutPressureWashing can we diy those?

[@josephhollowell672]

I got a question. I just bought a setup that is 5/8 & the parts listed are 1/2 inch will the 1/2 inch work with what I purchased? I’m new to this btw.

[@mattsievering8794]

I have a gas powered pump as well. What do you use for your gas powered system

[@AllAboutPressureWashing]

+Matt Sievering not sure your question

[@mattsievering8794]

@@AllAboutPressureWashing you said the proportioned wasn't good for the gas powered system. I was wanting to know what kind of blend manifold you used

[@AllAboutPressureWashing]

+Matt Sievering When we used gas Softwash system, we did not use a proportioner, we batch mixed. However, it is possible to have a proportioner on a gas system. There are several videos out there that explain it.

[@bryanfehse6546]

Or strictly pipe thread sealer?

[@AllAboutPressureWashing]

Yes you can use just the thread sealer if it is specifically made for your intended use

[@ajustice2010]

Update? Any need for change in design or use a different product ? Also where did you source your parts

[@zoemaravilla2538]

Theres a couple parts that look similar. Can you put the item number or part to know exactly what to get. Thanks! New sub!

[@thomaslutz2]

I don't see any links for the proportioner parts or a link to the ratio chart?

[@Naturalhigh8]

I'm trying to understand. So, if you have a gas motor you cannot use a proportioner because you need a bypass so you don't burn up your motor? Then if you have a gas motor you need to batch mix?

[@AllAboutPressureWashing]

Yea you can

[@MrChazz1516]

Where is the ratio chart Please and Thank you

[@michaelchartier4904]

What size hose barbs did you put on that? I unfortunately went the more expensive route and purchased one.... they came with 3/8” hose barbs, what you have looks bigger

[@AllAboutPressureWashing]

Those are 1/2”.

[@parton45852]

Do the 1/2 inch inlet and outlets work fine for an everflo 5.5? Im seeing some people using 3/4 outlets and dont want to start burning up pumps from restricted flow?

[@AllAboutPressureWashing]

+Joshua P 1/2 is good for the Everflo

[@mshaneweaver1]

Why dont you put the check valves "above" the meters? Seems like it makes more sense that way so that SH cant get to all of them. Can you elaborate on why you do it this way? Thanks!!

[@AllAboutPressureWashing]

+Shane Weaver that is smarter! Thank you for sharing!

[@zoemaravilla2538]

I just went to the list. On there there is a ryobi soap blaster tip. Thats not required for the proportioner is it?

[@3dp_edc]

Do you think 1/4 Pentair control valves would work? All the 1/2 inch ones I can find are either really expensive in Canada or the shipping to get it here is really expensive but j can't seem to win lol but I did find a Pentair 1/4 inch control valve & check valve combo for $58 CAD.

[@AllAboutPressureWashing]

+Dylan Unrau I don’t think that would work - would likely burn up your pump

[@bluecollarballers7315]

Will schedule 80 pvc work just as well?

[@AllAboutPressureWashing]

Should work

[@coachnate5747]

Dont see the link for the chart

[@neryalbanez5368]

I couldn't find the link for the parts list and where i could buy parts may be i can go to Amazon, but o would like to have the list

[@unclejonah]

Why do I not see where the parts list is? great info man… thank you

[@Asawade]

Where is the proportion chart located? I can’t seem to find it.

[@ryanbrewer5600]

hey your amazon storefont is inactive. i dont know if its just paused at the moment but could you get that running so i can buy these parts

[@alankunzman7831]

Are these all 1/2' fittings?

[@scuffedvegeta2756]

very good video

[@AllAboutPressureWashing]

Thx

[@blakeengland7784]

Do you happen to have an old manifold for sale?

[@AllAboutPressureWashing]

Nope

[@BoostedRex]

After 2 years is this still a solid setup?

[@JamesBrown-ed6sk]

Can you do a video on from the proportioner to the tank

[@AllAboutPressureWashing]

+James Brown I did - kzbin.info/www/bejne/bXzLZKhum5hpgs0

[@brandon6451]

Do you have any videos on plumbing?

[@Bode252]

Thanks bro

[@chingu81]

On the QuoteIQ mix calculator, how would these valves line up on the pull ratio? With the SH valve set at 1 and H2O at 1 you'd have a pull of 1:2. With SH at 1 and H20 at 2 would you have 1:3 in the app?

[@AllAboutPressureWashing]

🚨 $1 FIRST Month on 𝙌𝙪𝙤𝙩𝙚𝙄𝙌 : Text "𝐀𝐏𝐏" to 912-391-0095

[@everzamora9031]

Would this work with a 1" air diaphragm pump?

[@AllAboutPressureWashing]

No

[@jeremiahhughes13]

Is there a local store to go to for these metering valves? i have located a store near by with the rest just not the metering valve

[@AllAboutPressureWashing]

+Jeremiah Hughes Amazon

[@whitneytyus05]

Can I get a list on what to buy to be able to build this?

[@AllAboutPressureWashing]

bit.ly/PWEquipment

[@nick32141]

Thanks. Great video.

[@AllAboutPressureWashing]

+Omega1 thanks for watching!!

[@AllAboutPressureWashing]

Where are you located?

[@nick32141]

@@AllAboutPressureWashing Volusia County, Florida 32724

[@AllAboutPressureWashing]

Nice! Lots of competition down there!

[@nick32141]

@@AllAboutPressureWashing You’re absolutely right lots of competition. Anyone with a vehicle and a few hundred dollar machine is out there trying to work. Many working for just about nothing. If you’re honest with your customers and educate them on your workmanship and how things are done properly you usually can close the deal. It’s a tough market in Florida.

[@4everabeast79]

Can you make A proportioner for a gas powered soft wash machine? Do you have a video?

[@robertschreen9854]

Does the output ratio vary depending on your pump output? Say a 5gpm against a 7gpm or do the meter the same mix? I'm going to build this and use it with a 5.5 everflo. FYI your strait to the piont videos are the best.

[@AllAboutPressureWashing]

+Robert Schreen Robert, I appreciate that. The output of the pump makes zero difference, the metering system does it’s job regardless. It will work perfectly with the 5.5 Everflow, that’s what we are currently using. Also check out the link below, or the video about the pump were giving away

[@jonaskey]

Thank you for that

[@justinrichwine3909]

What do you need for a gas set up?

[@AllAboutPressureWashing]

There are several options out there for gas - I've had a few but have moved away from them. I would consult your local PW supply house to see what options they have available

[@luckycollins1431]

What size hoses for the proportioner on a 7gpm pump? What size for the water, sh, and surfactant?

[@AllAboutPressureWashing]

1/2

[@luckycollins1431]

@@AllAboutPressureWashing thank you. 1/2 even for the soap?

[@AllAboutPressureWashing]

1/4 for soap

[@lsgt5132]

Ok I'm new to this and been watching many videos on how accurate these valves are. From what I'm seeing the 150$ valve isn't any real difference than a 3$ one. I'm thinking the only real way would be to run half inch water. One half inch for SH, then a 3/8 for SH then a 1/4 for SH and each have a cheaper ball valve up sized so they only restriction is the hose size. So basically useing restriction that you can control to get a proper metering. Just open which ever ball valve for the ratio you want.

[@lsgt5132]

What do you think about this idea boss. From what I can tell your about as knowledgeable as one can get on this softwash stuff. Thanks for all the videos. I'm about order everything I need to get started and from what I'm seeing these vales for the money aren't really that great. So I was just thinking this way would be way cheaper and should be more accurate. Your thoughts?

[@AllAboutPressureWashing]

+ls gt use the link Description and buy the parts from the link, by the upgraded valves

[@tylerlee8315]

Could this work with pressure tek’s fat boy bandit ? It’s a 7gpm 12 v system

[@AllAboutPressureWashing]

Yes it will

[@mrkoolkdoingitanewway5740]

Where can I buy these parts from

[@troykisner4507]

Awesome!

[@memphismania32]

thank you

[@jonathancarrasquilla9019]

What number on proportioner do you put for surfactant on roofs

[@AllAboutPressureWashing]

It just depends on the pitch of the roof, how dirty it is, lots of things. You’ll just have to play with it and figure out what works best for you.