Thanks so much for the help with the jammer build, it worked perfectly! This is the first circuit I've seen that worked perfectly on the first try. Just a note for anyone looking to jam frequencies around 2400 MHz: you’ll need to swap the VCO chip for the YSGM232508 and adjust the resistors in the NE555 circuit to get the desired waveform. Keep up the great work!
@Tecnologiko2 ай бұрын
In what sense to adjust the resistors? Which ones should I use Can I do it without an oscilloscope?
@justanengineer55992 ай бұрын
If you do not know what you are doing you better give up before you get jailed man. Adjust means find correct resistor and capacitor values for NE555 triangle signal generator so it would generate correct voltage range (peak to peak) that alows VCO to reach 2.4GHz frequency. It will be hard without f.ex. FNIRSI oscilloscope to see this signal shape and parameters.
@justacupofjuiceАй бұрын
Hi! I would be happy if you could help me with creating jammer. Do you have email or anything?
@justanengineer5599Ай бұрын
github, check source code
@robertburgess74929 күн бұрын
@@justanengineer5599I'm more worried about a drone strike than jail
@justanengineer55993 ай бұрын
if you are looking for good power RF output amplifier search for something with heatsink and TQP7M9103 chip. Remember that most of these boards need to be altered to operate on specific frequency and you need to buy SMD capacitors to do that therefore extra knowledge is needed to make it work. Always use Yagi Uda type of antenna not the omnidirectional. EDIT: Also found that SBB5089Z chips may be useful as they serve as wideband amplifiers in most of the small jammers designs. They give 20dBm / 100mW power but it is sufficient to cover 15m+ radius. Look for 50MHz-6GHz amplifiers
@ElohiSilverEarthVentures22 күн бұрын
Thank you for that additional word of advice...more I learn the more i realize I don't know
@BalticLab3 ай бұрын
If you add some BPSK modulation with a clock-rate of 1.023 Mbps to the vco signal, you'll achieve even higher jamming power. This would ruin the remaining robustnes of the CDMA.
@justanengineer55993 ай бұрын
That is correct. The best would be to put fast Microcontroller with DAC instead of NE555 that gives best flexibility for VCO frequency steering EDIT. I checked with MCU + DAC and analogue type of sawtooth signal generator seems to work better. Also Noise type of DAC signal is not good. I think VCO has some setup time for frequency therefore the smooth adjustment works better. The signal driving the VCO needs to change linearly.
@treapymnm6519Ай бұрын
Man put so many effort for us , to teach us some professional engineering knowledge. Sub . Edit : why tf this channel is so underated ?
@justanengineer5599Ай бұрын
I think it is the question to the makers of YT algorythms 😃 In short : YT likes to promote shitty content. They like morons and they want you to become one If you are smart you do not fit to the agenda. You need to be stupid so they can fully control your behavior. Social engineering man...
@treapymnm6519Ай бұрын
@@justanengineer5599 Brother . Don't drop the crown 👑.
@mohammadmakki861528 күн бұрын
@justanengineer5599 thank you from 🇱🇧
@MyTube4Utoo3 ай бұрын
That's very cool, but we may need something else when they start sending the 'Terminator' AI robots after us. Which should be any day now. 😆
@justanengineer55993 ай бұрын
hold my beer... I will make it...
@mak82213 ай бұрын
Thanks for sharing mate. Great project.
@chuckcrizer3 ай бұрын
Remember, there is still RF power radiated from the back of the yagi. Normally it is minor but if your head is just a few inches / centimeters from the antenna, it could be hazardous when using high power.
@justanengineer55993 ай бұрын
exactly, i think yagi antenna's characteristics is visible at the begining of my video
@AhmetYusufYatkin4 ай бұрын
Waiting for this video! Nice jokes. Thank you. We just watch your videos as educational purposes
@pierpa_76pierpaolo3 ай бұрын
I am interested in such a project. It is just what I was looking for but I need to transform the frequencies (but not only also audio i voices and noises) into wav or mp3 format. I need to start getting all these components and get started. Let me know. Thank you very much.
@NottsOnline4 ай бұрын
thanks
@e_asier2 ай бұрын
You are a genious.friend...what should you do in my case? In front of my House...there are many Young people drinking at nights...they Talk to loud...what could i do to keep them far? I was thinking on a 4g 5g jammer to block them cells so they Will go to another place? Do you hace a tutorial to do that? Thanks in advance friend..
@justanengineer55992 ай бұрын
using 4G and 5G jammer is not a good idea. You will be found and fined pretty fast because cell towers have advanced jamming detection and positioning capabilities. If they are using bluetooth speakers there will be a solution for this in my upcoming video.
@irfanjaafar35702 ай бұрын
@@justanengineer5599 you will be detected if you used omnidirectional antenna and blast it for 24hrs, not if you used directional and direct it towards the receiver (target phone)
@justanengineer5599Ай бұрын
sure thats why I bought yagi uda micro pcb antenna
@ClaraWilkes22 күн бұрын
Us government could not care less. I have been digitally terrorized by a family member for YEARS and tried all legal means to stop it (collected devices, evidence, system logs, my recorded observations, etc) and hired professionals to assess and be willing to testify but I traveled by foot (my devices and car are continuously remote disabled) to visit in person my local police, mayor and city counsel, state Police, the FBI, Secret Service and other agencies to beg for help and they all refuse. They all say one of the others is responsible. After extensive questioning, apparently no one intelligent enough to handle the situation is employed at any of these places (including the FBI head of Cybersecurity). So, we are on our own. To hell with them. Do whatever you need to do. After dealing w this for YEARS and almost losing everything (I was about to die from being shut out of communication capabilities) I just now managed to get a phone working by jamming the malicious script streaming into my office. Next is a computer -and annihilation of the malicious signal itself. I would love to see the b∆℅¥€€√s drag me into court so I can show full evidence of their negligent incompetence! You could look into an LRAD also. Businesses use them to make loiterers feel ill. Good 🍀 luck
@effsixteenblock509 күн бұрын
@@ClaraWilkes You can use VoIP over ethernet cable. They can jam all they want and it won't affect you.
@PowerProjects993 ай бұрын
Thank you for your interesting content 💙💙💙💙
@tanko267327 күн бұрын
Super filmik, ciekawe
@pepethefrog71933 ай бұрын
The telescopic antenna u use is a mismatch at 1.5g and will destroy your power amp.
@justanengineer55993 ай бұрын
of course you are right. not matching antenna will break an amplifier in seconds. The radio power was very small so it did not happen - i was using the LNB as the power amplifier 😃
@katana-rl7gb4 ай бұрын
Nice 🎉
@TheMalerdaemonАй бұрын
👍🏻 Nice! And in the words of Bob Marley “We're jammin', I wanna jam it wid you, We're jammin', jammin', and I hope you like jammin', too”
@justanengineer5599Ай бұрын
I love this song😃
@ronaldwoofer50244 ай бұрын
yea but when i asked reddit for information on such a device they said it wasnt possible. So sick of reddit, is there a better place where you can ask questions about such devices? Things like robotics, sensors, GPS drones, etc?
@emiljagnic4 ай бұрын
Not every idiot deserves to know this information, lmao. Asking on reddit is not a good source of information anyways...
@justanengineer55993 ай бұрын
in times of electronic warfare and constant control everyone deserves to know how to protect himself. On reddit you may ask about what will happen in the next episode of your favourite TV series but not such things like jamming. People are like the sheeps not aware of upcoming slaughter. They like to be sheeps and live within their comfort zone. You know - the knowledge raises sadness... sort of speak
@emiljagnic3 ай бұрын
@@justanengineer5599 I am not sure about any electronic warfare going on, although I agree with you that people should have the knowledge and the possibility to use that knowledge to protect themselves. The only thing is, until that moment arises, there are also wolves disguised as the sheep. Knowledge can increase discomfort but also acting ignorant is a sort of means to an end. thanks for the great content!
@tyjohnston58893 ай бұрын
Reddit is toxic. Especially with newbies. It's a joke.
@turbo40853 ай бұрын
@@justanengineer5599 they are sheep and want others to become sheep
@randykitchleburger27803 ай бұрын
Thanks friend, I will try to not go to the jail.
@justanengineer55993 ай бұрын
haha but I bet others may want to 😀
@TheOneAndOnlySame3 ай бұрын
I was about to try to go to the jail but bro here just changed my mind
@justanengineer55993 ай бұрын
hahaha you made my day. I know sometimes I make mistakes in english
@Un_Pour_Tous4 ай бұрын
My friends deserved to be Jammed
@justanengineer55994 ай бұрын
hell yeah !
@mohamedbelafdal63623 ай бұрын
I bet you can increase the efficiency by using a pseudo random generator, but it will make things slightly more complicated
@justanengineer55993 ай бұрын
of course.. the video was just a test if the concept works EDIT. I tested with random number generator feeding DAC for random voltages 0-5V to drive VCO. Seems that analog sawtooth signal or triangle signal gives better jamming results.
@mohamedbelafdal63623 ай бұрын
@@justanengineer5599 thanks for the update, I wonder if that is due to the fast changing signal in the pseudo random causing the system to perform worse or if periodic signals are better at jamming?
@lyricss1-chmod2 ай бұрын
@@justanengineer5599 Hello! Do you have a diagram of how to assemble an analog sawtooth or triangle signal generator based on the ne555?
@justanengineer55992 ай бұрын
I used the diagram from this page : www.electroschematics.com/555-triangle-waveform-generator/ However I changed the components to following : 100K --> 10K 47K --> 4,7K 0,2uF --> 4,7nF 0,1uF --> 2,2nF It finally gave me best results with 1,5GHz VCO module ( the chip YSGM 151708 ). The triangle signal was around 44KHz frequency and the VTune was in the area 2V-3V which perfectly matched surroundings of 1575MHz GPS signal Even without the RF Amplifier I was able to jam GPS from 10+ meters !! The VCO module has 8 miliWatt of RF power on its own...
@justanengineer55992 ай бұрын
@mohamedbelafdal6362 : My DAC was only 5bits so the Voltage from 0-5V was coded between 0-31. I think at least 16 bits DAC is needed to achieve good results because you need to map the output voltage range to VCO chip characteristics ( Vtune Freequency generated) therefore best granularity is needed
@Tecnologiko2 ай бұрын
To disturb the Bluetooth frequencies (2.4GHz) between a speaker and a mobile phone Which VCO should I take because I can't find a 2.4GHz one and in this case would the rest of the circuit and the antenna always remain the same?
@justanengineer55992 ай бұрын
read the comments from yesterday man. I does not hurt. Just read the comments before posting any questions. Everything you need is there or on my github page
@UserRandom04676 күн бұрын
you can also make a piezo noise generator for hollow walls and windows ?
@flat-earther3 ай бұрын
RC toys use all kinds of frequencies like 433mHz, 900mHz, 1.2GHz, 1.5GHz, 2.4GHz, 5.8GHz
@justanengineer55993 ай бұрын
indeed to jam it you need couple of jammers each for different frequency and each with separated VCO and power RF amplifier and antenna. The video was just an example for single radio channel If you look at the commercial builds they have many antennas, guess why 😀
@lokiva85402 ай бұрын
Those toys operate mostly on 47 CFR 15 bands, a few on Part 18 ISM, and are subject to strict signal emissions and stricter out of band limits, plus are secondary spectrum users with a duty to shut down if or when they cause harmful interference to licensed/primary spectrum users on adjacent frequencies. Jammers by definition are intended to cause willful, harmful interference under US or EU laws, when operated on most bands shown for GPS or cel. WiFi or ISM has fuzzier legal issues.
@reeseherberger15253 ай бұрын
You seem really good at responding any chance you could explain the WAVE generator Ne555 configuration or point me in the right direction maybe even PM ME
@justanengineer55993 ай бұрын
In the demo I used an example diagram from this page : www.electroschematics.com/555-triangle-waveform-generator/ with modified capacitors to 4,7nF and 2,2nF which gave around 5KHz frequency. The best would be also to change resistors 100K to 10K and 47K to 4.7K. Anyway I would go for building a Sawtooth generator with at least 100KHz : www.falstad.com/circuit/e-555saw.html Also there are NE555 DIY kits with all type of signals : square, triangle and saw
@aleksandrokolodko359210 күн бұрын
Thank you !!!!
@Thiago-yl9qu4 ай бұрын
🎉🎉
@nathanwarner8076Ай бұрын
If I increase my input voltage can I increase my range? or is the range simply controlled by my amplifier?
@justanengineer5599Ай бұрын
According to the datasheet of VCO chip yes you can slightly increase the power, but if you want more range attach the RF amplifier.
@eaf2k2 ай бұрын
That's just L1 that you've jammed. There are also L2 and L5 bands.
@justanengineer55992 ай бұрын
yes of course and you can buy VCO to jam it as well. My phone was using L1 GPS band therefore I jammed only L1. Check VCO vendor page through my github links
@irfan_antennas3 ай бұрын
nice. can you share the links to buy capacitors and resistors?
@justanengineer55992 ай бұрын
just buy a complete set of full range capacitor values and resistor values on Aliexpress. Put there "capacitor set" and "resistors set" in the search window Just an example www.aliexpress.com/item/1005007101158585.html www.aliexpress.com/item/1005006186890215.html
@lilkrucivert4 ай бұрын
have you ever tried bluetooth jamming? i was trying to look into it but couldnt find anything useful
@justanengineer55994 ай бұрын
This device can do it. You just need to buy VCO for 2.4 GHz range and better RF amplifier board
@emiljagnic4 ай бұрын
Keep in mind when you do bluetooth jamming, a lot of medical devices use this communication technology. Such as pumps for medicine, hearing aid devices, pacemakers etc. I am a chronic disease patient and I use a medical device with bluetooth. I have no trouble of people exploring it but when you do this just keep this in mind that basically someones life might be on the line.
@lilkrucivert4 ай бұрын
@@emiljagnic nah was just thinking about using it on a bus when ppl are playing music using a bluetooth speaker
@emiljagnic4 ай бұрын
@@lilkrucivert Did you even read what I just said? A person that uses medical equipment with BT can be on the same bus that you are on too... Especially elderly people.
@lilkrucivert4 ай бұрын
@@emiljagnic i didnt mean public transport. more like school trips etc
@gtxsatria20102 ай бұрын
Hallo sir .i want test my Metal detektor with this project, how this jammer work for disturb my mechine because my mechine work veri veri low Frekwency just 18 KHz- 73 KHz.
@justanengineer55992 ай бұрын
you need to find VCO generator that works in this band. I saw only working in 70-120MHz and upper bands
@8-bitstuff507Ай бұрын
I don't understand capacitors that much so what rating are they both and can i combine multiple for example 2 nF and 5 nF to get 7 nF? Thanks
@justanengineer5599Ай бұрын
Cap 10V is enough if you are powering the VCO from 5V. If you want to get 7nF from 2nF and 5nF you need to connect these two in PARALLEL
@vincentnarasch693218 күн бұрын
how much khz out of the triangle wave generator do i need to achieve for 2600mhz oscillator? is there any kind of calculation i can use?
@justanengineer559918 күн бұрын
check my github for some starting values. I would say that around 40-100kHz triangle signal used for VCO modulation is fine enough Unfortunately there is no calculator for it. You need to experiment. You need an oscilloscope for sure
@misqpl4 ай бұрын
puk puk ... kto tam ... harcerze!! .... o tak ? niewieze .................... !!!!OTWIERAJ CHAMIE FBI NIE KLAMIE !!!!!!!! :o)
@justanengineer55993 ай бұрын
tak jak powiedziałem na początku wideo - wiedzę tajemną przekazuję za darmo ale trzeba być swiadomym tego co się robi i trochę odpowiedzialnym. Najlepsze jest to ze wszystkie części możesz na luzie kupić od pana Chinczyka. Zresztą różne takie urządzenia od dawna Chińczyk sprzedaje tylko za duże pieniądze
@misqpl3 ай бұрын
@@justanengineer5599 zmontowac moge i posiadac moge ALE nie moglbym tego uzywac , zaraz mi sie FCC by mie znalazlo.
@johnsmith-ro2tw3 ай бұрын
is it really illegal to jam GPS signals ? it does not affect GPS signal transmissions. To my understanding, it only makes geolocating your phone less accurate. It's like going outside and leaving your mobile phone at home.
@justanengineer55993 ай бұрын
of course it is ILLEGAL ! On the other hand is it legal and safe to fly a drone over your house and take pictures of what you are doing ? If you attach directional antenna and better RF amplifier you can confuse the UAV drones approaching your property. The phone was just an example because I wanted to check if it really works... If you build it with proper VCO frequency you can literally take down the drone because it will switch to safe landing mode - then you may rip off the SD flash card and wipe the recorded data..
@TheRisenPeopleEire3 ай бұрын
Yes as it interferes with emergency services depending on if they are in your area or not you can get a heft fine too.
@justanengineer55993 ай бұрын
of course - you need to be aware that what you are doing is dangerous and be responsible. this is what I am mentioning in the video. Jamming is illegal but you can buy jammers and parts for the jammers everywhere and no one is controlling it - so where is the logic ?
@TheRisenPeopleEire3 ай бұрын
@@justanengineer5599 Subbed man keep it up!
@robertburgess7496 күн бұрын
What size wires did you use
@justanengineer55996 күн бұрын
you mean antenna? you should use the one that matches frequency. For other points the cables are irrelevant
@oa18972 ай бұрын
Hi, can you help me to configure which bands are support by telecom I use and also how to insert that into the script or tool
@justanengineer55992 ай бұрын
I see you reaaally want to go to the jail. Use NetMonster app on your mobile phone to find out what are the frequencies in your nearest cell tower. But you must know that cell towers are having jamming detectors and can easily locate you within seconds. At least be prepared for the police because they will visit you for sure
@oa18972 ай бұрын
@@justanengineer5599 Eng I meant was to my telecom, I do see nearby tower but problem is I don’t know how to exactly enter them thought you can help me in this. Feel like it’s not correct format. The signal keeps on changing
@justanengineer55992 ай бұрын
what do you want to accomplish because i do not really understand.
@oa18972 ай бұрын
@@justanengineer5599 the bands to put in order coz I don’t know how to set primary band example to active CA something from 4g to 5G boost Kuwait STC
@justanengineer55992 ай бұрын
why do you ask for such things under the jamming video? ask under LTE videos. there is already video about such tool for Huawei based routers
@moon_iqАй бұрын
for 2.4ghz and a yagi anteena, do you think that i will need a better amplifier or the one in the video is sufficient? and thank you for the effort you put in this video.
@justanengineer5599Ай бұрын
that will all depend on the range you want to achieve. For 2.4GHz without a power amplifier but with LNB attached and directional antenna I was able to achieve more than 50m range
@loyaaheibam6277Ай бұрын
Which is the best for dji drone
@justanengineer5599Ай бұрын
just both 2.4GHz jamme + directional antenna combined together with 5.8Ghz jammer + directional antenna. You need to use both sametime
@CraBundy2 ай бұрын
Intelligent people are blind to what they dont know. Explain every single time/video please. I respect the knowledge but please, understand that most dont know the totality.
@justanengineer55992 ай бұрын
you are right of course. I will try to pinpoint some details in the next video.
@pngbtw2 ай бұрын
what ressitors you used?
@justanengineer55992 ай бұрын
check my github page. everything is there well explained
@yeethiolij5 күн бұрын
Is that possible to make a big Anti drone for example Bayraktar TB2 drone?
@justanengineer55995 күн бұрын
everything is possible but you need to know first on which frequencies it operates. do you know them?
Nowadays LTE operate on many frequencies so the answer is yes.
@unoproject203 ай бұрын
@@justanengineer5599 thank you adam, I have been to make a jammer for cars and drones 2.4ghz using edup / booster and next project, if I want to make a UHF frequency wireless mic jammer is the schematic the same?
@justanengineer55992 ай бұрын
yes all the same you just have to use different VCO generator per every frequency channel In the next video I will show you 2.4GHz Bluetooth jammer I have just bought from China for 15 USD :-)
@lyricss1-chmod2 ай бұрын
Hello, is there somewhere I can chat with you if I don’t bother you? I have questions about part n555
@justanengineer55992 ай бұрын
check the project page on my github, everything is there
@lyricss1-chmod2 ай бұрын
@@justanengineer5599 thank you, I just want to make a 2400 MHz jammer and for this I need a wave not of 2.2-2.7 volts but at least 3-4 volts so that the vco touches the 2400-2500 MHz zone, please tell me what to change in the circuit for this?
@justanengineer55992 ай бұрын
you will need to change capacitors for sure. If you change 10K resistor to 3.3K you should reach 3.5V at the peak. You need to experiment. I would suggest to buy some small oscilloscope to observe the signal, for example FNIRSI oscilloscope
@lyricss1-chmod2 ай бұрын
@@justanengineer5599 I just now have a small oscilloscope from FNIRSI :) I tried changing the resistor to 3.3 kohm and got a saw wave from 0 to 5 volts, will this work or did I do something wrong?
@justanengineer55992 ай бұрын
yes this will work. you may also try to change capacitors. experiment
@frenkeefrenkleen9743 ай бұрын
Ez a kombinácio így nem tud működni megbízhatóan. Kéne rajta fejleszteni. Van rá időd. Oldd meg tessék. Ha sikerült, jelezz majd.
@justanengineer55993 ай бұрын
I would but the point is I do not have the free time that is why I am posting the videos not so frequently
@dr.sahadevwaghmare14319 күн бұрын
yessssssssss..............
@loyaaheibam6277Ай бұрын
What is the range?
@justanengineer5599Ай бұрын
seen the video?
@nickspeakstruth133Ай бұрын
@@justanengineer5599could just answer it so that he could determine if it’s worth watching/building lol not being mean, just saying there’s many reasons for questions.
@justanengineer559928 күн бұрын
in my vid it was about 15 meters of GPS jamming range
@tinnawatkappaha9305Ай бұрын
How can i used for vco 70-400 mhz module
@justanengineer5599Ай бұрын
with these VCO frequencies you can only jam FM Radios or Pagers (that like to explode..)
@Omni_Digital_TechАй бұрын
Would you sell these pre made?
@justanengineer5599Ай бұрын
no
@nickspeakstruth133Ай бұрын
@@justanengineer5599why? Are they super illegal?
@justanengineer5599Ай бұрын
yes. You may make it but you cannot use or sell it. At least in US and EU
@ElohiSilverEarthVentures22 күн бұрын
@@justanengineer5599but let's just say we're making a developer type educational board yah? my son is new in the tech world and is needing to examine a device that's already been put together...that works yes?
@justanengineer559922 күн бұрын
I am not sure that explanation will work for the authorities 😃
@Paavo19914 ай бұрын
Czy można użyć cc1101 + wzmacniacz+ antena?
@justanengineer55994 ай бұрын
mozna. ale wzmacniacz działa tylko w jednym kierunku a cc1101 jest dwukierunkowe. Do nadawania jak najbardziej mozna ale stracisz tor odbiorczy. pamietaj tez ze cc1101 działa max do 1GHz
@RichardVaccaro-k6w10 күн бұрын
Great for drones
@CraBundy2 ай бұрын
I am amazed, remember what your doing here, intelligence in the wrong eyes will be detrimental.
@CraBundy2 ай бұрын
Some of your viewers might try this near intelligence agencies without knowing or airports. In that case they will get sniffed out....jailed, you need better disclaimers than this, they practically need to be in a Faraday cage environment for total non detection/testing. Get real.
@justanengineer55992 ай бұрын
true. But the point is how to get cheap faraday cage. Other thing is that these RF power amplifiers need to be fine tuned to work properly and most of them simply do not work at all. To make use of them a lot more of information and practical skills are needed. The VCO generators do have couple of miliwatts power on their own and can be successfully used for low range jamming even without power amplifiers
@CraBundy2 ай бұрын
@@justanengineer5599 there is no cheap options, if we are talking about a room and requires engineering knowledge to do so like electrical isolation from earth/ground can be hard to a non engineer to even contemplate. I have built Copper lined Faraday cages... As for "fine" tune, a basic Google search for the frequency bands is all i would need to do, its reckless to think other wise, i may overly think this because i already know how. But to think that some of your viewers aren't intelligent enough to connected the dots and do malicious acts is incomprehensible. They are watching engineering videos they are already on the right steps, but are they in the right direction? Keep doing what your doing but please understand that the viewer has to understand totally what this is capable of, so they dont do it, few simple modifications can shut down alot of equipment/safety.
@ColinMill13 ай бұрын
Are you aware that most drones flying autonomously can fly accurately for a considerable distance without GPS or coms? Take, for example a Pixhawk Cube controller running Ardupilot. It has triplicated IMUs and will track several kilometres with an accuracy of only a few metres.
@justanengineer55993 ай бұрын
yes of course. with good sensors and accelerometers they may reach the destination, but consider that they will not be able to transmit any surveillance or reconnaissance data to the headquarter. And for sure they will have no 100 percent accuracy to hit the target. I know that they may also use ADS-B 1090MHz but it is still not as accurate as GPS
@ColinMill13 ай бұрын
@@justanengineer5599 Well, jammers won't stop them transmitting reconnaissance data unless you can get close enough to the receiving end.
@justanengineer55993 ай бұрын
they wont stop transmitting but you will disrupt the transmission at some point. I think for such type of devices only big EMP from close distance can help
@ColinMill13 ай бұрын
@@justanengineer5599 Yes - unfortunately there are quite a few people in authority (especially here in the UK) that don't appreciate these difficulties
@gjbcapital18473 ай бұрын
Accurate imus are very expensive. I doubt there is a cheap units that’s off only a few meters after several km.
@siljoe847 күн бұрын
Please sell me 2 of this I live in Dominican Republic here is not illegal
@justanengineer55997 күн бұрын
buy on aliexpress and use these guys to ship to your place www.colisexpat.com/en/delivery-shipping/dominican-republic/aliexpress/
Please make a video of Faraday cadge(cage) test environments for your videos if not you leave your "viewers" liable to the court of law! Be a true engineer, dont mascarade.
@justanengineer55992 ай бұрын
I will if I find something suitable. On the other hand nowadays everyone can buy a jamming device on cheap. Go to the www.aliexpress.com and put "usb rf jam source". You will get plenty of already tuned devices for 15$. You will be amazed again.. I am telling you if someone wants to do something bad he will find the way. The real problem is that the components for jamming and full devices are fully available to anyone. I am talking about chineese vendors
@tntomega2 ай бұрын
today if you fart you go to jail dude give me a brake
@justanengineer55992 ай бұрын
there is a book titled 1984 which exactly describes what is happening in this shithole now
@nickspeakstruth133Ай бұрын
@@justanengineer5599facts! Which is the only reason we need to know how to build stuff like this. After seeing the modern war footage, it would be HORRIFYING to not have access to some of these to stop drone attacks if you were being hunted. That’s why I’m here 🤣🤣
@ClaraWilkes22 күн бұрын
The gov does not care about us from what I have experienced. We are on our own. Demand a jury trial. No one out here is going to vote to convict a fellow citizen for being forced to defend themselves. Be sure your community is aware of JUROR NULLIFICATION. Post flyers, spread the word
@salsilva81326 күн бұрын
Ucraine tutorial
@justanengineer55995 күн бұрын
lessons learned
@flat-earther3 ай бұрын
hi justanengineer, have you become a flat earther yet? If not I suggest watching _Level with Me (2023)_ by Hibbeler Productions
@justanengineer55993 ай бұрын
not yet but I think I have a big chance to become one 😀
@BlackVelvet4463 ай бұрын
What you are presenting is a crime!!!
@justanengineer55993 ай бұрын
This design is not my invention - check this page showing how to build it - everyone has an access to this knowledge and I just built it to check if it works : jammers.store/wiki/how-to-make-a-gps-jammer/ Using these devices is a crime. Building it is a science. You need to distinguish these two things. It is clearly mentioned couple of times in description and in the video. You can buy it from china sellers - even more powerful jammers because this one is just a a toy. Its like with the knife - it is not a weapon until u use it as a weapon. If someone attaches gps tracker to your own car and you do not know about - it is a crime. How can you protect from someone tracking you possibly for bad reasons ? give me a clear answer please ! If you really want to help go to Aliexpress and tell them not to sell jammers, VCO and power RF amplifiers Ok? We will see if they listen to you. The china sellers are also posting videos here on YT go find them and tell them they are promoting the crime Well maybe You have some better ideas for example how to deal with military armed drones or the missiles approaching you to kill then let me and other civilians know, genius..
@gjbcapital18473 ай бұрын
@@justanengineer5599The knowledge is out there but I ll suggest to never transmit more than a couple of mWs. Using an amplifier is irresponsible. The vco chip you used has a 7dBm rating and could achieve that 5-10 meters range by itself when correctly drived. An amplifier even a 1 W one is dangerous for other users.
@justanengineer55993 ай бұрын
it not so easy with such amplifiers. Most of them are tuned only to one frequency and not exactly the same as advertised by chineese seller. They require to be adjusted by replacing some capacitors and coils which is beyond the knowledge of ordinary people. As a result they more likely damp the signal instead of amplifying it.
@lokiva85402 ай бұрын
@@justanengineer5599 That jammer store site is cringe, as it calls swamping, "spoofing", a series of techniques to yield false positions, not disrupt reception of timing signals. It also says GPS signals are transmitted at low power, as it lists typical received signal strengths and says nothing of TPO levels. Many of these potential jamming and countermeasures issues are important to understand for engineers, as are EU, US, and other spectrum allocations and legal issues. ISM bands (47 CFR 18) generally support legal drone jamming on those drones using 900 MHz band comm, while Part 15 gets fuzzier. Most of the other suggested applications of this video promote blatantly criminal activities, but not knowledge, at least wrt US or EU jurisdictions (with massive exceptions to military contractors).
@justanengineer5599Ай бұрын
I am not promoting anything here... The video was just an experiment if using the knowledge from internet site and widely available parts like VCOs I am able to build working jammer. I am pointing couple of times in the video that it is illegal and it is also in the description along with the links to FCC rules and EU regulations. Everything is there. Believe me.. If someone wants do the bad things he will not make jammer himself because it is more difficult than buying a fully working jamming device for 50$ from chinese shops and you will not even know about it. Where do you live man? in a desert? Look on aliexpress, even on Amazon the jammers were sold. Focus on that : www.nbcnews.com/tech/security/drone-radio-frequency-jammer-signal-online-defense-technology-rcna135103 In short - because you are trying to ban everything even the knowledge there will no longer be good engineers in your country. You are cutting off young people wings making them focused on some irrelevant things like social media instead of learning and doing science. Even now China eats you on breakfast while you can only outsource engineers work to other countries because you have not enough skilled people anymore Instead of promoting the knowledge you are promoting the shit.