www.supercoolsliderule.com -- This video tutorial illustrates how to set up a defrost heat pump board to bypass for cooling. To set up to bypass for cooling, one simply needs to follow these steps on a defrost heat pump board.
Пікірлер: 78
@michaelcostello69916 жыл бұрын
Good video. It clarifies the functions of the defrost board and the fact that it is just needed really for heating and some safety interlocks
@btknowlton9 жыл бұрын
If you have comments that are helpful or suggestions on how to improve a video please post it but if you don't have anything valuable to add then please keep it to your self.
@mickeylojkar57695 жыл бұрын
Why get a common from the board if your bypassing the other wires? Shouldn't you get common from the tstat wires?
@1251PrintHouse2 жыл бұрын
Yes you should.I was thinking the same thing
@christopherpaul29389 жыл бұрын
Bryan the way you ecplained it is for.experienced technicians, it seemed a bit confusing, the easiest way would be to just unplug the two orange reversing valves wires from the defrost board and simply connect them on the each side of the contactor so the valve can get its 24 volt. The valve will always be energized when ever there is call for cool. Great vedeo though!!
@SombraLocs9 жыл бұрын
exactly!
@michaelkranz25297 жыл бұрын
Ya I think this guy want's to show off his electrical engineering degree , but any tech can do that task in way less moves than his dumb ass video , Oh ya , why are we bypassing the control anyway ?
@Seawolfvital7 жыл бұрын
Christopher Paul what if condenser fan motor relay stuck open? U energized reversing valve but cond fan motor won't run. I would never bypass defrost bord(SW Florda) unless it's late call and I'm unable to get replacement part (most cases -next day in the morning it is installed).
@osiriscorporation12656 жыл бұрын
simplicity at its finest, thanks smart brother!!
@PBS-nm1uu7 жыл бұрын
please do one on how to read the control board.
@aadilali15107 жыл бұрын
THANK U SO MUCH
@914peru10 жыл бұрын
thanks for you help I'll buy you slide rule I'll buy my defrost board in October
@OnePointLander2 жыл бұрын
Why would a defrost board fail?
@jeffjula2 жыл бұрын
because it's a man-made item.
@michaeljennings34856 жыл бұрын
Good video but when you connected the common lead for the thermostat you connected it to the black lead on the board and not to the thermostat wire I think it was the grey wire
@ricoswavae5123 жыл бұрын
Yeah i saw that too, good catch.
@aarongreen878410 жыл бұрын
Okay, in the beginning you moved the black (C) wire out the way, @ 1:43 to 1:53, and tried to put the red wire from the contactor to the light blue (C) wire from the thermostat. Then later you put the black (C) wire from the board with just the red and orange (C) wire and the light blue (C) wire was not connected. Now which wires need to be connected in that stage? All light blue, black, red and orange which equals four wire or does just three need to go together, black or light blue with red and orange?
@drouse3655 жыл бұрын
Aaron Green Just the light blue,orange, and red. Forget the black coming from molex plug (board).
@zmanjz20013 жыл бұрын
Great tutorial my Board went out. It's on backorder and it's been 102° here. This worked great and the temp is dropping as I type. Thank you!!
@Alienspecies6352 жыл бұрын
I’m about to try this tonight for a customer that got a bad board on a new unit 🤦🏻 3-5 days for the board to get in then I have to go pick it up and install it
@michaelpope29465 жыл бұрын
Shouldn't you connect to the valve end of the orange wires not the board end? I tried this and burned up my transformer not sure what I did wrong.
@boobieloc97343 жыл бұрын
That's what I'm thinking.. because how would it power the valve. why wire the board if you're bypassing board
@matthewcrews40343 жыл бұрын
Hi how are you can you make a video .showing how to bypass the condensor fan relay on board for defrost and add and external relay to allow cooling and heat I've replaced this carrier board 3 times in a year and a half .just put a new board and new condensor fan motor just in case old fan motor was pulling to high of laps causing the relay to fail . However the board failed a week later anyway I've had the whole system checked over and voltage tested they found no issues but the board keeps failing the last unit I had the man installed a external relay for the fan which worked perfect until I had to get a new unit due to outdated freon thanks and I hope you can help
@Onatena4 ай бұрын
thanks for this great Video I was struggling with one heat pump I was getting 24v but the board was not working well, after watching this video I end up bypassing it and it worked 😂
@outlawguitar19 жыл бұрын
Something wasn't right, I wired it exactly after spending an hour repeating the steps, plugs mine in and 60 seconds later, a loud pop!!! Maybe redo this video and rethink the wiring and be a little more in detail, thanks
@JuanDiaz-vm1pv4 жыл бұрын
Thank you for your time. Question: my AC/Heat Pump is freezing up around the indoor unit coil. No AC at all. Thermostat and inside fan are working, filter and A-frame are clean, drain plug is NOT clogged. Outside fan and compressor are working too. I haven't measure capacitance, but assume dual capacitor is good since compressor and fan both run. I haven't check for low refrigerant yet (R-410A). What could possibly be the problem? Would the defrost control board have anything to do here (it's spring time and only inside is freezing). Thank you much in advance!
@bhaskarper9092 жыл бұрын
What did you do to fix it, I have similar problem?
@musclemoney44792 жыл бұрын
@@bhaskarper909 low refrigererant
@DJatVRR9 жыл бұрын
You should make another video with a more simplistic explanation of a simplistic solution and correct your mistake while you're at it.
@davidjackson30692 жыл бұрын
You just cut half the words in the unit when all you had to do was run the "Y" wire directly to the contactor. Land the fan wire on the L1 terminal of contactor. Then you could have placed a common wire on the opposite side of the contactor and boom when the contactor pulls in you have air conditioning now you have to unspice all those wires and fix it all back ridiculous amateur status.
@johnj249611 ай бұрын
what about the reversing valve wire just move the input wire down to the extra connection next to the yellow control wire on contactor
@sultanramza93798 жыл бұрын
Thank you for this video. I followed the steps and it worked perfectly. Just two issues I'd like to highlight to help others: 1. Please refer to the wiring schematic for specific colors of the reversing valve. Mine were black. 2. Also I blew the fuse at the a/c handler in this process so my thermostat wasn't working. One I found that and replaced it everything worked well.
@glennthompson16202 жыл бұрын
SMerry
@Ajax23416 жыл бұрын
Thank's Good Video. Ive worn out a couple of supercool slide rule already. a lot of information on that card. I use it all the time.
@herbertvega7493 жыл бұрын
Good job !!!!! thank you for sharing !!!!!
@manna561010 ай бұрын
So, I wanted to bypass the defrost board for heating, then just leave the reversing as is.
@TalentNetworked Жыл бұрын
Great videos. Can an ohms OL on a Solenoid cause the 3amp fuse in the AH to keep failing? Can’t get Low Voltage on Contactor, changed contractor, same issue.
@RifullOfTheWest6 жыл бұрын
@SuperCool Slide Rule" can you make a video on how to make yourself a light wieght, small home built window defogger wire setup. I have a velomobile I need to make a defogging wire setup, but can't figure out how to do it, and where to get the wire.
@hg2.6 жыл бұрын
Not good for beginners. "Don't do this at home.
@chadoxdcfan4 жыл бұрын
Could I just jump yellow and orange and leave common alone? Shouldn't common still be present no matter what?
@sarahgracebrooks26298 жыл бұрын
What if you don't have a RV and your indoor fan is wired with the unit....Package/A/C and GAS??
@louisg456710 жыл бұрын
you right Aaron he messed up.. the red wire from the contactor is suppose to connect to the common on the thermostat wire coming from the air handler and that completes your 24v coming from the transformer the other yellow wire which is your call for cooling he has correct
@nitrofan9175 жыл бұрын
Do the red and blue wires that you jumped get plugged back into the relay? Thanks.
@viper223045 жыл бұрын
Thanks for the video. Can you do this with rudd and rheem?
@ricoswavae5123 жыл бұрын
Yes you can.
@trickyanims78528 жыл бұрын
Basically just take the low voltage cooling wire out of the board and connect it at the contractor. 🆒
@RM-gw8ue4 жыл бұрын
How can you bypass the control board and still retain the ability to use the heat strips ?
@romeshthomas79497 жыл бұрын
How to wire up a hot water coil to an air handler using two relays and an aquastat
@kaster20144 жыл бұрын
Good video ... but very bad explanation
@andrewlaurice822710 жыл бұрын
Great information! Thanks. Andrew Laurice
@gotchaplumberАй бұрын
Great video!
@manuel128882 жыл бұрын
Thank you so much for your help
@gotchaplumber6 ай бұрын
Great video!
@danpan44256 жыл бұрын
Can you bypass the board for heating and cooling?
@Ggg777773 жыл бұрын
Yes but different way
@abnergallo6960 Жыл бұрын
Thank you so much
@giorgioguidolin3 жыл бұрын
Thank you
@saltrue15557 жыл бұрын
Nice tks
@Carskinify9 жыл бұрын
The defrost cycle doesn't work during the summer so if you just use the summer ac,why would you need to bypass the defrost cycle?
@acoustic40379 жыл бұрын
Carskinify You don't "bypass the defrost cycle" as you put it. You bypass the defrost board. The board can burn out (a relay on the board) and not pass power (24v) to energize the main contactor and not allow the system to run or cool at all. I'm still new at hacks so I just get the replacement board and install it. People go hot for a few days, thats life.
@foghornleghorn85369 жыл бұрын
acoustic4037 Sounds like you should probably be doing installs. Leave the service work to an actual technician.
@acoustic40379 жыл бұрын
Foghorn Leghorn your comment serves no purpose except to insult. Why bother if you can't be constructive or helpful.
@foghornleghorn85369 жыл бұрын
Merely pointing out that by making this statement "People go hot for a few days, that's life." You clearly indicated that you should not be a service technician.
@WilliamBelliard9 жыл бұрын
I enjoyed your video thank you for the education, I do have a question. I have a temp star unit and I replaced the contractor, defrost board and fan board along with a new honey well digital thermostat. All looks well, the ac blows cold air but I did notice that the condenser fan is always running/spinning even when the blower inside is not blowing anything. Also the air power of the air coming out of the vents inside is not as strong and the other units. Can you please help
@btknowlton9 жыл бұрын
William Belliard You may want to ensure that the wires feeding the condenser fan are connected to the load side of the contactor instead of the line side (they should be on the side opposite the incoming high voltage wires). Hope this helped.
@WilliamBelliard9 жыл бұрын
Bryan Knowlton Thank Bryan. Is the load side L1 or L2 correct? I mean have you heard of this? Could the fan motor be bad as well? Or if it spins that means its good. By making these changes will it increase the speed of the fan outside thus increasing the air blowing inside?
@michaelkranz25297 жыл бұрын
Oh ya , if you can speed up the out door fan , it will surely blow like hell inside , dude stay away from this trade , your scaring me .
@luishernandez5394 Жыл бұрын
Sounds like you wired the low voltage incorrectly and by that I mean maybe at the furnace you installed the y wire on the r terminal instead of it being on y and therefore your your condenser is always running. Or you wired your fan high voltage going too the line side of your contactor that you replaced something is mis wired need more input.
@OcRefrig6 жыл бұрын
Good video !
@BradMillsXRP9 жыл бұрын
I tried this and it burned my house down. So my laywer is wanting your General Liability policy number
@michaelkranz25297 жыл бұрын
Excellent reply , I love it , people like him don't realize that people shouldn't be attempting modification like that , leave it to qualified service company , I would sue the shit out of him , he is an accomplice to disaster.