I am an amateur, so please don't mind if I am doing something wrong in this video.Thank you so much.
Пікірлер: 27
@bmillar37442 жыл бұрын
A handy video to see all the steps involved but a few things are giving me the fear! First, having the car propped up on rubber floor mats via a scissor jack and an axle stand in completely the wrong place. With the force you may have to put through the breaker bar to crack the nut on the wheel bearing, the car's at a huge risk of slipping off. I'm also noticing no wheel chocks in place and even if the car is in gear with the handbrake off, it can still move slightly. At the bare minimum you should stick the wheel under the car as a fail safe in case everything goes wrong. The brake caliper is left hanging by the hose which puts a lot of strain on it. Also didn't see any anti-seize being applied to the axle nut, no copper grease on the back of the brake pads and you managed to get loads of grease on the face of the new discs. I hope you have good life insurance cover and hopefully anyone watching this will take these points on board too!
@victoriawilson3796 Жыл бұрын
I lost it at the hammer snapping lmao
@garrettwarren18133 жыл бұрын
Thank you! Can you add a list of tools you used in the description?
@shineyboots3 жыл бұрын
Just the right vid for the job. No b/s. Cheers
@stevecramer92332 жыл бұрын
Lots of problems with this video, not just what was mentioned regarding safety by Bob Millar. The rotor taken off had outer stud guides, while the new rotors (and bearings) expected the 12mm studs to be screwed in. Are they supposed to be optional??? All the excessive force on the bearing by hammering the top instead of using the 32mm socket like finally done. No high-temp bearing grease used anywhere, certainly no 207 ft lb torque wrench. Didn't see anything cleaned properly, certainly not brake cleaner used to clean up anything before reassembly, with greasy fingers on the surface of the rotor. Watch this so you know what NOT to do!
@anfa88332 жыл бұрын
I agree with you . I forgot to mention that I was doing this for the first time in my life. Thank you so much for advices next time I will pay attention on that. Thanks again 🙏
@kennethchristopherwest3 жыл бұрын
Thank you so much for the video! Subscribed
@anfa88333 жыл бұрын
Thank you so much .I really appreciate it.
@sebastienboisvilliers6132 Жыл бұрын
Au final le moyeu a été changé..... mais quelle sauvagerie dans son remplacement. 😂😂😂😂😂😂😂😂 Mais merci pour cette vidéo
@sanchoo99103 жыл бұрын
good job!!!
@anfa88333 жыл бұрын
Thank you
@jayc.19107 ай бұрын
How did you get the broken bearing seal to slide out a little so you have space to use the puller tool? 3:32
@amykrim27742 жыл бұрын
👏👏👏
@estevanrios79483 жыл бұрын
What issues where u experiencing that u determined that bearings needed replacing
@anfa88333 жыл бұрын
Annoying sound at the begin than terrible loud sound. Thank you
@almostforgotten23693 жыл бұрын
I'm having the same issue. Loud roaring noise at about 40 mph and it gets louder the faster you go. I also have a vibration in the front while in 2nd gear...prolly CV axles. FIAT = Fix It Again Tony
@narmo7989 Жыл бұрын
My bolts holding the brake carrier on are allen key bolts and are inaccessible
@andrewbennett1377 ай бұрын
You don't need to remove the brake caliper carrier.
@dayglowjim Жыл бұрын
Everything Bob Millar said, and why don't you narrate, or sub title at least?
@anfa8833 Жыл бұрын
Yes, you are right ✅️ I will do it . Thank you so much. I really appreciate it 🙏
@hufman98072 жыл бұрын
"Most common problem"? ... It's a bearing. They wear. That's it. Get a floating car if you don't want to replace bearings at scheduled intervals.
@jayjay0032 жыл бұрын
It’s still a problem, and it’s still common
@tomthomson3278 Жыл бұрын
Cowboy!! the fact you let a bearing get that bad tells me all i need to know
@anfa8833 Жыл бұрын
Cowboy, this is not my car . Second, this is my first time doing bearing without any knowledge . Do you understand now? I know I know you don't because you are cowboy !!
@anfa8833 Жыл бұрын
Stručnjak!! Gdje si stručnjak? Nisam te prepoznao!!
@damaizjordana1185 Жыл бұрын
Where is your content?
@StopTargetingOurKids2 жыл бұрын
lol wtf, I wish someone with a modern abarth 2012+ would do a front bearing