A great You tube piece on what NOT to do to remove a Chuck..and damage the Drill to boot !...
@felixyoghurt32917 ай бұрын
For the cave man viewer
@victor-lw7iu5 ай бұрын
@@felixyoghurt3291😂
@ahmedmashhour1912 Жыл бұрын
Lesson learned, If you don't understand how something works, just bang on it with a hammer until it gives up on working again🤣🤣
@rajbhullar22188 ай бұрын
Rytt😂😂
@GatotAdi-cb7nm8 ай бұрын
Iyo yo
@tomaszkluska64194 ай бұрын
Film powinien mieć tytuł 'jestem idiotą'.
@Sdskotdr19 күн бұрын
इसलिए,अंग्रेजों ने इसका नाम hammer machine रखा।।😂 ⚒️
@frankdavidson96753 жыл бұрын
this is the correct way to remove a chuck take the drill bit out look down inside chuck you see a screw turn it clockwise to removeit the turn chuck counter clock wise to remove it do not use a hammer
@tomaszkluska64194 ай бұрын
Ależ gdzie tam. Najpierw należy walić młotkiem.
@rolandogallardo36402 жыл бұрын
Best way to change chuck I have ever seen so far
@vishnudanraj25702 жыл бұрын
To me that's the hardest way, plus drill can damage
@melvinyenyen56133 жыл бұрын
Centre of chuck internally you use a cross head screwdriver and unscrew the lock bolt. Then turn chuck anti clockwise to unscrew.
@abdelrhaimmahir52912 жыл бұрын
والله حرام عليك
@apagla35186 ай бұрын
❤😢😢😮❤❤
@joseduartesantos26225 ай бұрын
Amigo, você está certo! Está é a melhor maneira para trocar um mandril!!! 😊
@tomaszkluska64194 ай бұрын
@@abdelrhaimmahir5291 :))
@anicetogalorio32173 ай бұрын
Good job and nice tip on how to damage a power drill and get a new one 😂😂😂
@aqtv14693 жыл бұрын
This guy is actually crazy
@fenech973 жыл бұрын
To change a drill chuck , usually you turn it anticlockwise towards you, then you put its key in the chuck and tap it a bit hard with a mallet. That should loosen it.
@aasageer3 жыл бұрын
Yes. That's the simple way to replace The chuck , and it doesn't take much time.
@gengspock2 жыл бұрын
Ini solusinya
@gengspock2 жыл бұрын
Ini solusinya kzbin.info/www/bejne/f4CmoXt_nplrha8
@samshanker57532 жыл бұрын
@@aasageer ya bro
@ezequielrodriguez2376 Жыл бұрын
Sinceramente fue el mejor video que me ayudo...😃
@fenech97 Жыл бұрын
Some electric- drills use the system of putting the key in the chuck opening the jaws fully and tapping a bit hard with a mallet on the key to un-loosen the chuck. There are other ways of removing the chuck.
@joewoodchuck38242 жыл бұрын
I only replaced one on a portable drill and it had an Allen head cap screw down the inside bottom of the chuck. I had to loosen that first, then unscrewed the chuck. It pays to read the instructions that come with a new one. I also replaced a drill press chuck, but that was Morse taper.
@bassmaster20093 жыл бұрын
i like your safety shoes my friend.
@hirayaman2462 жыл бұрын
Best way of how to NOT change the chuck 😂
@hardoyosuwasono4453 жыл бұрын
Itu namanya merusak didalam chuk ada bolt tapi melepasnya justru searah jarum jam, langsung lepas broew
@siamaklighvani3951 Жыл бұрын
Thank you very much , I used angle grinder to remove the chuck but I cut the round bar hitting it with hammer is a right think to do.hitting with hammer is a must and effective
@cachhomevideo15462 жыл бұрын
Can I replace drill chuck without hammering?
@TumpaTalapatra Жыл бұрын
I have no words to describe it. Sometimes thinking is necessary before going full Thor mode.
@Studywithstudent974 ай бұрын
😂
@007camera3 жыл бұрын
That was one of the unknown application of hammer! Nice job broooo👍🏻👍🏻👌👌
@EgyptCanada7 ай бұрын
Thanks a lot fot this great videk Would you please advise me, how many millimeter is the inner thread size of the 10mm drill chuck. Thanks in advance.
@sailingdev3 жыл бұрын
Thanks for sharing how to get a new drill
@arnoldarnold64863 жыл бұрын
Using hammer no good the impact can damage inside if you play video make it good work so that everyone understand improve your knowledge thank you
@jorgemiguelfregozoguido40192 жыл бұрын
No así nose hace eres mexicano lo digo por huaraches piteados
@ranasarkar38982 жыл бұрын
This kind of machine should not be used rough and tough and rather to be repaired or change of parts carefully as far as possible delicately. The inner parts may be damaged.
@vicenteramirez84583 жыл бұрын
Solo tienes que calentarlo y sale rápido y entero sin daño alguno para utilizarlo de nuevo en otro taladro.
@Ometecuhtli4 жыл бұрын
How to destroy your drill for hammer lovers.
@bfbbcjcbn25004 жыл бұрын
B
@benadicka34623 жыл бұрын
5
@giuseppetesta86003 жыл бұрын
H78
@mohammedazaroual59253 жыл бұрын
😁😁😁😁😁😁
@gengspock2 жыл бұрын
Ini solusinya kzbin.info/www/bejne/f4CmoXt_nplrha8
@capitainehaddock93884 жыл бұрын
Watch on youtube, you’ll find good videos on how to change a chuck on your drill.
@luischerrezcherrez41323 жыл бұрын
Magnífico.....! Asumo que el Sr. de la foto es el autor de la técnica de vanguardia para cambiar el mecanismo de lo que quedó del pobre taladro.
@hugocastagnola1562 жыл бұрын
Una bestia.
@rodeldeguzman99692 жыл бұрын
It is very simple to change the chuck into the drill, open widely the chuck to see the inner center screw loosen the screw to counter clockwise if the srew is very tighten apply a liitle bit force so you can easily unscrew... you don't need a hammer
@mauriciobejaranoilherrero2 жыл бұрын
Si abres el mandril al máximo encontrarás un tornillo alen rosca isquierda solo tienes que sostener la llave y accionar la máquina sale en un instante
@mariomoyano6922 жыл бұрын
Cómo hacer las cosas mal un vídeo de un inútil tratando de mostrar lo que no se debe hacer
@mauriciobejaranoilherrero2 жыл бұрын
@@mariomoyano692 exacto a marraso saca el mandril con la herramienta de presicion jajaja a masaso limpio
@cergeiivanov3141 Жыл бұрын
С торца вала при раздвинутых держателях сверла ставиться винт с левой резьбой!
@ГеННадийГлодя Жыл бұрын
Так ведь чувак не ищет лёгких путей... 🥴🥴🥴
@cergeiivanov3141 Жыл бұрын
@@ГеННадийГлодя 😁😁👍👍
@1971cand4 жыл бұрын
Jak udało Ci się nakręcić film, skoro taka prosta czynność zajęła Ci tyle czasu? :-)
@muhammadhafeez74412 жыл бұрын
Very Good hafeez Bhai nice video 👍
@grande60752 жыл бұрын
You will damage the machine by using a hammer that is not the proper way to do it.
@zulfikranzulmos40663 жыл бұрын
He's just doing it the unorthodox way 😂😂
@karmawalaelectric49883 жыл бұрын
Bhaijaan very good video very good information video Allah Pak aap karo bar aur aapki channel mein Barkat ata Farma👍👍👍👍👍👍👍👍👍👍👍👍👍
@NareshKumar13 жыл бұрын
Very nice message
@nooruddeenku9962 жыл бұрын
How to change drill chuck❌ How to destroy your drilling machine ✅
@FDiOfi2 жыл бұрын
Can someone teach this guy to how to use screwdrivers?
@ManojKumar-yv2pk4 жыл бұрын
Wrong solution, armature may be damage
@chinopacia55442 жыл бұрын
2 million saw this very informative videos..keep it up..we learned a lot..
@andreaavola9172 жыл бұрын
Ma non è un po troppo distruttivo cosi a martellate ?e poi é dicuro che non si deforma l'indotto ,ci credo poco cosi...vi è un'altro modo quello di svitarlo delicatamente.
@danielnagy572111 ай бұрын
I had a good laugh, thank you.
@shakhawansalih56012 жыл бұрын
the best and easiest way to remove the old head , i recommend it for every one , thanks
@michaelangelosuarez32014 жыл бұрын
title should be,how to remove and replace a chuck NEANDERTHAL STYLE...
@hafijurrahmanofficial71368 ай бұрын
Thank you very much.❤
@skpintu10633 жыл бұрын
Usse vi ak asan tarika hai!
@jameskeene22942 жыл бұрын
All the drill chucks i ever replaced had a screw holding it on and then threads, but what do I know get a hammer and beat the hell out of it 🤔 shows you how dumb i am
@williamcastaneda55013 жыл бұрын
Por dónde coloca la broca tiene un tornillo
@stevekapp64623 жыл бұрын
Did anyone notice the electric cord going to this drill??
@yakatdookith2059 ай бұрын
That man is crazy😂i bet when he changes his pants he tears them off and remove the pieces😂
@nuryadix409527 күн бұрын
Cara ini berhasil sy praktekkan
@idetubeid9 ай бұрын
Worked hard 👍
@insaneingineer6424 жыл бұрын
It can unbalance the saft उसके बाद ड्रिल बिट डान्स करेगी 😅
@officialm00163 жыл бұрын
😂😂😂😂😂😂 sahi baat hai bhai
@marquezkenken68694 жыл бұрын
I THOUGHT THIS IS THE CHANNEL OF HOW TO BASIC, I AM BASICALLY WAITING FOR THE EGGS TO BE THROWN OUT 😂😂😂
@rahmatfizia3 жыл бұрын
LOL 😅
@keegangarrett3293 жыл бұрын
pro trick: watch movies on Flixzone. Been using it for watching lots of of movies during the lockdown.
@koltonniko3633 жыл бұрын
@Keegan Garrett yea, been watching on flixzone for months myself :)
@hcic98603 жыл бұрын
Who knew that just beating the shit out of it could be so effective 🤦🏽
@rizwansaleemi67214 жыл бұрын
blunder.... a use of hammer on shaft don't fallow this'll damage the drill
@abdurahmanpemalang2399 ай бұрын
Bagaimana cara merusak presisi sebuah chuck bor? Ikuti video ini
@inversioneschamed3 жыл бұрын
Eso se llama trabajar a lo talibán... pobre taladro.
@riktapaulsarkar81042 жыл бұрын
Ese kon drill chuck change karta he bhai, drill chuck ke andar ka screw clockwise ghumakar khol lo agar screw ka head bit ki wajay se kharab ho gaya hai toh v koi problem nahi, drill chuck ke pass me ek spanner laganeka jagay rehta he usme ek spanner fasake fir drill chuck ko pipe wrench ki madat se pressure se anticlockwise ghumao easily open ho jayega ! Simple. Hammer marnese toh machine kharab ho jayega ??
@josron6088 Жыл бұрын
Thanks. 👍
@ramaraodhulipudi4263 жыл бұрын
నీలాంటోళ్ళందరూ యూట్యూబులో నేర్పించేయటానికొస్తున్నారు. అంతేలే జనాలు ఖాళీగా ఉన్నారు, యూట్యూబు తేరగాఉంది. కానీండి. మరిన్ని వీడియోలు రుద్దండి జనంమీద.
@michaelmonter40504 жыл бұрын
You distroying the drill
@vhelfredeluces30783 жыл бұрын
Yap distroying the drill
@vhelfredeluces30783 жыл бұрын
Open the cover of the drill and make sure be safe how to make sure Kane make it to safe to remove the drill bit
@julioribeiro95402 жыл бұрын
Tem um parafuso dentro do mandril philips rosca esquerda a ser retrado e recolocado
@sarbjitkumar4686 Жыл бұрын
Hahaha excellent engineering
@Amit_J4 жыл бұрын
Remove your contraceptive the same way.
@royalmachinetoolsajmer91379 ай бұрын
Very good 👍❤️❤️
@suhelahmad62603 жыл бұрын
Thanks Bhai for this information
@flaviocortes61523 жыл бұрын
Desde la ciudad de Mexico muy bien si me lo platican no lo creo mucha practica. Intentaré ese método graciad
@blueboy1231006 ай бұрын
I would be wearing some steel cap boots if i was him 😊😂
@setiawangiri1013 Жыл бұрын
Nice
@tobedetermined41804 жыл бұрын
Why do you need a drill? A hammer fixes everything
@pascalfrancis31273 жыл бұрын
You noob
@دپښتونقامادبيوجره2 жыл бұрын
He is a hard working guy you may watch his other videos of saving nature and environment.
@vita71282 жыл бұрын
Рискует отколоть ось редуктора, лежит с таким дефектом
@Santosh_Kumari8405 ай бұрын
Good video 🎉🎉
@maxedwards76122 жыл бұрын
I do the same to change the whisks on my wife's Kenwood mixer, I'll get it right one day
@BalapKayuindonesia2 жыл бұрын
Pake kunci L bos di masukin ke bor lalu di ketok
@angelpeppar44303 жыл бұрын
Yo he cambiado varios mandriles de taladro, con un solo golpe aplicado correctamente sin maltratar el taladro y sin destruir el que vas a cambiar, para mi gusto y humilde opinión esta que presentan es una mala idea
@edilbertodiaz74893 жыл бұрын
Qe brutalidad lo saco a martilo
@victormurcia1783 жыл бұрын
Creo que al señor que está cambiando el mandril, lo están necesitando para sacarle un mugre del ojo a un paciente Se que lo va a lograr, lo que me aterra es cómo lo haría.
@masmariochannel4 жыл бұрын
I like videobyou sir😄😄🙏
@sheikhmuhammadfaheem75632 жыл бұрын
O yar is mai threads th to hit q kr rh th hammer se?
@refugiocamacho20192 жыл бұрын
La necesidad de los Paquistaní e Indues .abrazos
@dantearresepaulini91893 жыл бұрын
Si no sabes sacar un mandrill ,no hagas videos esa no es la forma de sacarlo xq malogras los rodajes
@prashanthb65213 жыл бұрын
This is "How NOT to change drill chuck".
@EileenHudson-lc7bw Жыл бұрын
Just put the key in the chuck and hit it with a hammer anti clock wise
@felixdelacruz78736 ай бұрын
Gracias 🙏
@creativemind96614 жыл бұрын
Waat laga dala puri drill machine ki😂🤣😂😂😂
@edwinmendoza-zn4ed8 ай бұрын
Banging it hard with hammer might destroy the shaft of the motor!
@IamSchmo2 жыл бұрын
After watching this I have a headache. I'm going to fix it with a hammer too. LOL LOL LOL ...........
@أحمدقورش4 ай бұрын
السلام عليكم و رحمة الله تعالى و بركاته عمل ممتاز .
@felixyoghurt32917 ай бұрын
*When all you have is a hammer, all problems are treated like nails*
@rioprexchannel97982 жыл бұрын
Good job.....done like n subscribe
@edwardcarcallas37083 жыл бұрын
Wow great job
@batmasterson75066 ай бұрын
I miss the part where he totally destroys the chuck and drill
@amjadhani89293 жыл бұрын
That is NOT how you replace a drill chuck!
@dagudunagesh62032 жыл бұрын
My dear this procedure is wrong. Keep a 1" to 2" length screw or rod in one of the three holes of chuck and beet on it by 🔨 in tangential way ,anticlock wise direction.
@greggerodias9501 Жыл бұрын
Boss saan ba ang location ng shop mo
@jimcushman50606 ай бұрын
Crazy I hope he’s not the guy that repairs your pace maker
@احمداصليح-ط3ط3 жыл бұрын
هاد إسمه هبل؟ الرأس له برغي عكسي يمين بفك بطلع بكل سهوله
@francelinocesario93312 жыл бұрын
Gostei da resposta parabéns
@sabberhm3360 Жыл бұрын
ধন্যবাদ
@shajihpd42303 жыл бұрын
This is pattan bay 😄😄😄😄
@lijojoy772 жыл бұрын
He forgot to put screw holder. It will hit definitely in his head 😀