How To Change The Light Bulb On Aprilia SR 50 (2005-2021) Models

Do you know how to change the light bulb on Aprilia SR50?
🏍🛠🔨
If you don't, check this video till the end!
🔧
Even if you know, you can watch this video and tell me what you think in the comment section below.
All rights reserved.
This video does not include any paid promotion.
DISCLAIMER
This video is only for information purposes. I cannot guarantee against any kind of use of this information. SomethingOfEverything assumes no liability for any damage or injury caused as a result of any of the information contained in this video. Use this information at your own risk. SOE recommends ONLY safe practices when working anyhow and or with tools. No information contained in this video would create any expressed or tacit warranty or guarantee of any result. Any injury, damage or loss that may result from the use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user itself.

[@robertbullard3324]

Thanks. Can you get those bulbs from any parts store?

[@somethingofeverything4646]

Its a H8 light bulb and you can buy it wherever they sell scooter parts or car parts

[@somethingofeverything4646]

www.ebay.co.uk/itm/261038117809

[@jenny-masterchef]

U can better upgrade it with cree leds.strong and save lot of power so u can turn both on.

[@carlosripoll2403]

Came here expecting an easy fix for a non-mechanic guy - Step 1: Remove front wheel My f*ing god

[@somethingofeverything4646]

Lol

[@theo2522]

How did you change the left one for me the cooling pipe from the radiator goes right out side it and makes it impossible to pull out. I have sr 50 r 2020

[@somethingofeverything4646]

Move the pipe a little using your other hand ... its rubber...and you need to make just small ammount of space its not like you need to remove the radiator pipes... i know its little bit hard but look i never removed any pipe and ive changed it. Just twist the lightbulb holder WITH ONE HAND AND WITH THE OTHER ONE TRY TO MAKE SOME SPACE PUSHING THE RADIATOR HOSE. Greetings my man

[@theo2522]

@@somethingofeverything4646 wow thanks for the super fast response. I will try what you said when I get home. Also I changed mine to led will that cause any problem?

[@somethingofeverything4646]

@@theo2522 if it is led then its ok... xenon is not good it may damage your headlight plastic.And if you like my channel please subscribe its free :) i will post more videos of my aprilia sr 50 and more subscribers is like more help for me to do new videos. Thanks :)

[@theo2522]

@@somethingofeverything4646 you just got a new sub

[@domciau]

Had the same problem changing the bulbs today (mine is 2018). I tried so many techniques but the one that worked the best was disconnecting the light bulb from the wiring and only then pulling the bulb out. I have to admit it wasn’t easy to get the clip off the bulb but it is possible and if someone did this without disconnecting the wiring inside the scooter I don’t know what kind of a planet they’re on, it’s really impossible to do it that way!

[@romano9914]

why did you disassemble the wheel?

[@somethingofeverything4646]

Because the lightbulb is hard to get without removing the front wheel

[@TIM01]

can’t you just remove the front covers?

[@g8some]

Fyi you don't need to remove the front wheel lol but I also have a 2021 Aprilia motard.

[@somethingofeverything4646]

Brother this is from experience.The light bulb is so hard to dismantle because of the water hose in the front so you must make space as much as possible for you to work on that light.

[@g8some]

Ok well I did mine without removing the tire. I installed leds

[@somethingofeverything4646]

Yes and you see the motard is a little bit different than this one. Motard is air cooled so it doesn't have the water hoses in the front. Thats why it is easier :) Greetings