How to charge lithium phosphate battery|Tp5000 module|32650 cell|3.2volt battery charger|6000mahcell

[@4gtech377]

Note : Solder the F pin (I forgot about that while video making)

[@malathins466]

All the best shiva❤

[@ganeshwoodenarticle7130]

How much time it takes to 0 to 100% change?

[@4gtech377]

6 hours

[@armandojuarez2064]

This was exactly what I was looking for. Thank you for making this video.

[@4gtech377]

🙏😃

[@souptiksamanta9231]

Is there any alternative to charge 3.2v lfp cell without using tp5000

[@4gtech377]

👇You can use this adaptor 👇 makerbazar.in/a/sc/amp/products/3-2v-32700-32605-li-ion-charger

[@fireofenergy]

A 600 mA 5v solar panel would work fine, right? If so, can we parallel the tp5000 for higher current using multiple 5v panels connected to its own tp5000, then to the same (or larger) lifepo4 cell? Thanks!

[@4gtech377]

Tp5000 module output current is changeable: You can see a R100 resistor below the 'Sanya'l abel , below R100 resistor ther will be a point to solder the resistor,if you add R200(0.2Ω) you get the output of 1.5 ampere or if you add R100 (0.1Ω)smd resistor then you get 2 ampere output If want get more than 1ampere current then you should connect the heatsink..... If you 600mA solar pannel it takes more than 10hours to full charge..

[@purthercabahit9071]

Does this work to 16850 lifepo4 as well?

[@4gtech377]

No,

[@redentorsola2096]

It's ok use 6v 10w-20w solar panel input to charge 32650 using this 2 module?

[@4gtech377]

Ok,but it doesn't not full charge your battery,,you can use use voltage booster module with this

[@ddddaaddaaaa]

if I'm going to use a 6 volts of this type of battery, do i need active balancer?

[@4gtech377]

If you use the same battery shown in the video then you connect the 2 battery in seris to get 6.4 volt,Then you must add 2s BMS and 7.2volt adaptor for charging Thank you for commenting please subscribe 🙏

[@rickypulanco7144]

​@@4gtech377 Hi Sir Im planning to build 6v 2s2p . What charger I need to full those batteries. Thank you

[@4gtech377]

If your battery gives 6 volt when it fully charged then use 7.2 volt adaptor and connect any 3amp diode ,,,,,,

[@nero44284]

Apakah bekerja maksimal? Karena sejauh yang saya tau, banyak BMS mengajurkan tegangan masukan 3,7v. Tadinya saya kira perangkaian sebagai TP5000 - Lifepo4 3,2 - BMS tapi ternyata di vidio TP5000 - BMS - Lifepo4 3,2

[@sambasivatarra3819]

What is the cost of all parts and where will i purchace

[@4gtech377]

Battery :maker bazar-₹249 makerbazar.in/a/sc/amp/products/32700-3-2v-rechargeable-6000mah-lifepo4-battery-cell BMS :maker bazar-₹79 makerbazar.in/products/3-2v-bms-1s-12a-lfp-32650-lithium-battery-protection-board?variant=42631902462192&currency=INR&gad_source=1 Tp5000:maker bazar-₹75 makerbazar.in/a/sc/amp/products/tp5000-3-6v-4-2v-1a-lithium-battery-charger-module This is the price when I bought these parts, Currently the price are changed, Thanks for commenting, please subscribe 🙏❤️

[@aligul4035]

What is output voltage

[@4gtech377]

Module output :3.6Volt 1Ampere

[@4gtech377]

Battery output :3.2Volt 6Ampere

[@aligul4035]

Than how to make it 5 volt output and or we need boost up 5 volt module How much time its backup

[@4gtech377]

@@aligul4035 back up is according to your usage

[@redentorsola2096]

it's ok to use 6v solar panel 20watts input in the module?​@@4gtech377

[@bs3176]

🔥👌

[@chaithangowda9198]

💥💥

[@xXxbloodhoodxXx1]

Why 😂, a 1s Bms it acts as a charger to, you don't need the TP5000 for that u can use the TP or a Bms

[@4gtech377]

Then how you convert 5 -9 volt to 3.6volt...to add full charge indicator

[@xXxbloodhoodxXx1]

@@4gtech377 ok

[@herzog6689]

@@4gtech377 Desolder the connection on the TP5000 to get 3.6V, so no need for BMS.

[@RiyazBaloch-ty3uq]

بسر جی سیل کتنے کا ہے

[@4gtech377]

250 INR