How to check King Pins on a Semi Truck.

[@firzen0000]

This video is as good as it gets. Short, straight to the point, and gives you everything there is to know about it. Please do more how-tos, especially on Volvos. It helped me a lot as a young tech.

[@keeno7316]

I’ve been trucking for five years and didn’t know kingpins were on steering tires. Learn something new everyday

[@J_TRAIN]

You can tell he’s a damn good mechanic, great video and right too it.

[@ryanlouk9565]

Love the flag in the back ground gentlemen keep up the good work

[@eddyramirez81]

Lmfao....this is what makes America great diversity...not the flag

[@HeartPumper]

Thanks Seba & Jose! Good idea with such shorts. Very informative & it's keeping the channel alive!

[@J.Ross-33]

Thank you for this video fellas, much needed information

[@TheFied09]

Great tip, but what if your wheel bearing is loose?

[@princepanda816]

A way I use to confirm if it’s a bad king pin is that I put my finger where the axle meets the spindle and pry on the wheel. If it moves I know the problem is kingpins. But if not it’s probably a bearing issue, then I torque the bearing and check for play again. It always works for me.

[@Function180]

@@princepanda816 or have someone apply the brakes

[@markwaschke1635]

Check bearings i jack up wheel push top of tire and check play, this guy does the king king test property, buy checking from the bottom of the tire. I never put it in the rim holes but I built a bar that looks like a "J" its about 5 feet long

[@geoestrada5001]

This is very valuable information about front axles, thanks

[@joehighsmith2951]

Thanks for the tips, doing my old cab over soon, shimmying around 60mph. Just had a 3 axle alignment and all ten new rimscand tires trued and balanced, replaced rear intermediate shaft and universal joints. Most common cause of equipment failure is LOL=lack of lubrication. If you run your own truck and don't have a grease gun onboard and these failures happen blame the guy starring back at you while you brush those teeth

[@LiLEFILMS]

I deliver next door. That’s crazy I knew this was the shop and never actually been inside. Thanks for the tips.

[@cjbassi1]

Please do more diagnostic like this. Great info. Would be great if you went into “Odd tire ware “ show what causes them. I always have trailers with uneven ware the tire shops just scratch there head like they don’t know the underlying cause. & just slap new tires on and send us on our way. But I know that’s just putting a temp fix. It still eats the next tire the same way

[@geo6460]

Tell me about it man. No mechanic will take their honest time to do a proper diagnosis. They are as good as a dealership nowdays. We have ended up with lousy guys as mechanics, very unprofessional, and just want to make money. That's all.they care. Keep paying them bills

[@marchingpackofCeHS]

That wear is absolutely not kingpins. That is lack of rotation. Ever notice how its the outside of the right tire and inside of the left tire? Also you don't use a bar for checking king pins. Using a bar is for ball joints and has become common from auto mechanics working on large trucks and thinking the procedure is the same. I can almost guarantee that kingpin was not bad.

[@realskata16]

So what would you use to check them? My driver tire is true and square when looking across it but my 3 month old passenger side steer tire is wearing more round on the edges inside and out but not the middle.

[@andyg817]

Great video, i would say a lack of grease on the king pin will wear the bushes out quickly, every 2 months or so , to grease them up...

[@alejandroaguilar9038]

Wobble is balance AMIGO! This Axle isnt bad, they should have showed bearing check and tierod check. KINGPINS are around $1500.00 labor and service.

[@crashnburn586]

What your feeling is your wallet getting thinner! 😂

[@pokerman9108]

King pins are cheap if you do them yourself

[@MagDag_]

​@@pokerman9108 4000$

[@pokerman9108]

@@MagDag_ I did my 2012 freight shaker, new kings pins, front brake shoes, new bearings, and tie rod ends, for under $1000 bucks in parts. Got it all done over a weekend in my driveway. these shops are a rip off.

[@shawnjarman9860]

@@MagDag_ I just purchased a set of Kingpins for my Peterbilt, and just under $400, yes 4 hundred! Where are you buying your parts!

[@Stich46]

That jack on ubolt very questionable???

[@6Counterstrike]

First time seeing that

[@jaygraham5407]

​@@6CounterstrikeI jack under the u bolt quite often

[@vicpetrishak7705]

Apply service brakes to distinguish king pin play from steering axle wheel hub bearing looseness .

[@lukaslt88]

The movement felt in this video could also be wheel bearing play ?

[@apnews2u]

Thanks for the info. TRUCK YOO!

[@Andre_Beth]

Suggest you hold the camera steadier or get a tripod.

[@LAtxien24]

Thanks guys this video really helped me.

[@moremilesmoreproblems6330]

I was lucky to catch mine early as soon as I felt it and saw tire wear. Was not ready for that repair bill.

[@timmay2k]

I’m hearing clicking from my steer axle. Guess my king pins are going bad. I have yet to do it have over 1 million miles on my 579

[@godsok1]

Great video! Thanks

[@efrenlopez8776]

How expensive is that replace the king pins?

[@evguenimertodjan9783]

👍 Another value to our community!! Thank you guys!

[@467inc]

When I go around curbs it feels like I'm sliding across ice. Also I have a lil too much play for my comfort. Does that mean I need to change my king pins?

[@veroniataylor7603]

I have a 2014 Hino box truck and what you demonstrated is exactly what i am experiencing. Thanks,

[@vladimirazor2079]

Did you fix it already

[@BuckeeBorden]

You guys are life savers thx you so much ❤

[@JoseSanchez-jo4lx]

I first here lol thank for all the tips and thing you put in ur channel

[@TruckYoo]

Thanks for watching Jose!

[@paulmurray6958]

Most places won't let diagnose with the mechanic is I just drive away and fix it myself🐺

[@withbothfeet8593]

Good stuff, thank you.

[@markwaschke1635]

I made a bar which I call a hocky stick. Its about 5 feet long anf looks like a "J". The way he checked it at first thats how I check. In Ontario Canada we are only allowed 1/8" of movement. Before it was 1/2 inch

[@wildapach]

Where ur shop at I would like to see if u could have a look at my truck

[@terrellscaife2411]

So you guys gonna make a video on u joint removal

[@kb3809]

Great info🤙

[@josephlettier5640]

Thank you for the information

[@cristoperodriguezgil8075]

Would this cause inside wear?

[@damadpatter2839]

Keep it up fellas Lv the content

[@TruckYoo]

Thank you!

[@alexanderanderson8878]

What about shaking from 50 to 85

[@DJSTOEK]

Thanks

[@MrCease99]

Do you work on Prostars? I have a 2014 with the N13

[@Nicholas1999]

Would this cause grinding when turning slightly, right?

[@the.porter.productions]

Porter greetings.🤩 It has been such a long time since I checked the kingpins for any play, especially a big semi. If your camera was on the ground or a stand you could see it better. What I’ve found is this…If you do one side you should do BOTH because it will eventually happen to both sides of it’s not already. Agree? Now the big question is how many hours and cost does it entail for just the kingpins? Please advise. 🧐

[@JC-fi9yc]

Thank you for this very informative video. Now I'll be able to verify what the mechanic is telling me

[@tigreuniversidad1]

The wear in the tire it’s in the inside where all the weight go.

[@467inc]

Is the truck sitting on the ground? So I don't need to raise it up off the ground?

[@michaelbraddy2463]

You have to raise it until the tires are not touched the ground

[@BC-iz8gt]

That's exactly what mine is doing between 40 and 45 and 50 miles an hour is a 2022 Kenworth with only 93,000 miles

[@as7736]

Awesome, many thanks

[@the.porter.productions]

Porter greetings! 🇺🇸 Usually, if you have wear on the kingpin on the left side, would you also have wear on the right side as well? Did this truck get both replaced? Around how much would this cost in your shop? Generally speaking, I’ve learned that whatever you do to one side you also should do to the other side, even if there are NO signs of problems on the other side. This is what I’ve learned and what others have told me. Good stuff! Thanks for sharing. 🥰🤩✌️

[@saidabdulle4592]

alignment shop telling me you need to replace king pins because one of my drive tire is bad, is that possible? thanks for youre information

[@cjbassi1]

Subbed !

[@daviddelatorre9621]

I got my ki gpins checled and said they are good, got new tires and got all 3 axles aligned and got tires balanced and still truck is shaking at about 45-50 mph. Shocks are 5 months old and also got king pins done about 6 months ago. Any other ideas on fixing that wobble?

[@daviddelatorre9621]

Also drag link is new

[@pokerman9108]

@@daviddelatorre9621 alignment

[@elkservices8780]

Hub bearing

[@Fernando_Alferez]

Anyone can do that, but do you know how to get the readings of a failed king pins. There is a procedure using a dial caliper.

[@franciscocontreras1208]

Thats toe in,,king pin it's ok,,check rear alignment,..

[@marcoeldetropoja]

Can you just replace the shim/washer whatever you want to call it, can it just be replaced without having to buy a new king pin?

[@alex1701waller]

That's what I said. Everyone claims you have to do the pins too. Liars

[@hakunamatataadventurebus5944]

A little vertical play is not an issue in my opinion. Worn bushings would cause lateral play which requires repair.

[@elkservices8780]

​@hakunamatataadventurebus5944 what about in lateral bushing wear just change the bushings you think that works????

[@BikeLife_Swizzy]

Hey I got the same wear on My steers and a wobble/vibration under me not the wheel that comes n goes after 35mph it will do do it for hours then won't do it for hours I've replaced drive tires steers driveline center bearing shocks Torque rods but cnt find the issue been to multiple shops as well where u think I should check next. Thank You

[@Mr7E38]

Hi, are doing caster alignment at your shop? I have a 2019 VNL860 which is pulling really bad to the right. Alignment was done 3 times already, new tires and it didn’t help at all. One of the shops told me the caster is out of speck and that may be the problem.

[@pokerman9108]

Look up “how to align your semi truck layman’s” great video on how to check everything with basic tools. Alignment shops are terrible. Diy is the way to go.

[@martinflawless675]

I’m looking to buy a freightliner cascadia what years would you say is the best dd15 far as reliability and what years would you stay away from

[@realskata16]

I’ve always heard to not buy a truck with the dd15, many mechanics in my area say this and that the dd13 is much easier and cheaper as far as rebuilding goes when that time comes. Have you bought a truck yet

[@thebestleathers105]

If you could keep that camera steady it would help me comprehend the symptoms much easier

[@cheesebottle2844]

Thanks dawg..

[@Josiah_Harder]

Why Jack it up on the U bolt? That doesn't look good but idk maybe there's a reason

[@johnsonberry6750]

This is b.s because he dont have a gauge to see the manufacture spec !

[@komoru]

You may want to get a tripod for your camera. That's some really shaky camera work.

[@jeramiekochlefl-bodner5965]

All he had to do was stabilize his hand on the bumper. Fkn annoying.

[@Silentknight052]

Lock the brake up and take away wheel bearing play. Or just maintain the kingpins properly

[@albertmontana3932]

Era!!! Wheres Richie

[@OminousCamaro]

Its good send it

[@Flatlower]

where's your dial indicator? there's an actual in service spec. You don't guess. Use the proper tool to measure and check manufacture specifications.

[@RobbyJHope]

There is nothing wrong with that kingpin.

[@RobbyJHope]

@@BlizzMeister1 Thanks

[@gogobadr27]

True. TA charged us over 6k to change the king pins & chocks & some other parts for a shaking truck while driving but they didn't fix the problem & was a waste of money & time.

[@8004william]

What your grease said 👏 😏

[@NA-qo6og]

Good info but the shakiness of the camera is unbearable.

[@LmanTrojan1212]

how not to jack up a truck 101

[@carmodkings9500]

Imagine blow out on the wheel .. would take out the fuel filter

[@TARANS012]

Real test is you have to disconnect Tie rods !

[@sisbrogaming1072]

👍

[@nunyabuziness8421]

They are fine. Hardly any movement. Rip off mechanics

[@TheFoezee]

people don’t realize their front axles might have a slight bend. a good alignment shop will bend them back

[@TheBlkac1]

The camera guy needs to not move/swing the camera so much...I'm getting dizzy trying to watch.

[@brandonmeikle8820]

You could see it on camera if u left it alone, he's constantly moving it

[@bluewing2287]

Well that was not the camping that was the bearing the drum was moving not the camping he got to be careful with the mechanic because they are rip off

[@lariosfregosoify]

Sell the truck because of king fins😂😂😂😂😂😂😂😂😂

[@jammingwithmiki8912]

🤡😂

[@selimosmic661]

🤐

[@joeyoung3319]

You can't pick it up on camera because you're bobbling the camera around like a child.

[@jeffgreen9109]

Does anyone know where these guys are located? Im in Chicago.

[@tubeup]

Just look up era trucking

[@Jake-be2os]

Maybe if you could hold the damn camera still

[@ictviamfortruthgoogleisspa5886]

little free play is OK