How to Configure Two Routers using CLI in Cisco Packet Tracer

[@Majmuncek1]

OMG you're better than my teacher who is trying to explain me this at least for 1 month. She's should be fired and you should be my teacher. This is so simple. Thank you!

[@NetstrikersDotCom]

+Majmuncek1 hahaha.. Thanks

[@chevaldodavidson1361]

smh he's better than my teacher too

[@swelihlemkhwanazi]

short,simple and straight to the point.You've got my subscription :)

[@NetstrikersDotCom]

Thanks a lot :)

[@JTvlogs984]

I've been in and out of Cisco stuff for a few years but never really grasped it as well until now! Sir as this will help me so much! Thank you :)

[@karan_for_you]

Flawless, your tutorial was my friend. And yes, I would like to say that you are better than my teacher also. Thanks!

[@faheemfaansari4431]

Karan Singh can you give me your contact num

[@RedSunsSHChan]

You saved me in my school test QAQ Great networking tutorial, Thanks a lot >v

[@Samantai]

Thank you a lot, this was very clear and engaging, thank you for putting this up!

[@brentlyflowers1186]

Thank you for helping me. I was trying to connect to two router for the most part of my day and by watching your vide0 it really helped me.so than you very very much. May GOD and JESUS CHRIST bless you and everyone else in existence .

[@NetstrikersDotCom]

+brently flowers Thanks a lot :)

[@brentlyflowers1186]

no biggie keep doing what you do. I just want you to know that your knowledge and expertise and time is being helpful and I appreciate you for them, so, "Thanks once again"

[@ganapathynaikar1075]

Kadak bhai ek number bhai better than CLG teacher

[@yungerallenelectricalcontr6415]

I've never learned it so well!!

[@vineet8thegreat]

Thank you very much Sir Your way of explaining is too good

[@NetstrikersDotCom]

Thanks a lot :)

[@faheemfaansari4431]

Vineet Kumar can you give me your contact num

[@bakorkharkongor1983]

Thank you very much it was a very clear concept and learning how to run the CLI and do stuffs with it is kind of interesting now

[@awaisjabbar8304]

Veryyyyy Good explanation.......... Keep it up.

[@petercasey6311]

Great tutorial Aaditya. It really helped me a lot. Many thanks.

[@brendenscott8787]

Thankyou Sir you made it soo easy for me!! Thankyou soo much!!!

[@pkrl]

It is so helpful to me to understand. Thank you very much.

[@revadan]

holy macaroni! that was fast and easy! thanks!

[@edwintjoa6099]

Nice video. Clear and concise. Just a question, when do we need to use a router rip command then?

[@luqmanhakim7960]

thanks so much sir .. well explained and so ez to understand .. GJ (Y)

[@chevaldodavidson1361]

omg this was reeeally helpful, thank you very much XD

[@syedfahadalam3414]

sir you are amazing the way you are deliver lectures is awsum..sir i want to start from the beginning from where i will get a beginning classes kindly tell me it will be highly appreciated\if possible than provide me your classes link here thanks

[@ccmoviemaking]

great tutorial, thank you! It would be useful to know how to protect it with passwords too :)

[@NetstrikersDotCom]

+c&c c&c Thanks a lot , If you want to set password then type the following commands.. Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#line con 0 Router(config-line)#password cisco Router(config-line)#login Router(config-line)#exit

[@ccmoviemaking]

thanks! exactly what i needed ^^

[@Reeddollaz14]

Great video 👍

[@angelaarlene787]

thank you so much this is very helpful!

[@huyvole9724]

Is this static or dynamic route?

[@adilmughal8097]

sir, you are the great.

[@faheemfaansari4431]

Adil Mughal can you give me your contact num

[@susilbiswa9208]

thank you very much ,, was so easy...

[@shivagadiparthi8322]

Hey thank u for ur video ,I have a doubt when we ping pc in different network do we need static routing ?bcoz in the video u didn't do routing manually please respond to me

[@chadnanali111]

Thanks sir. I just want to askthat as you have used serial ports to connect the routers. Can I use gigabit Ethernet ports to connect them because I am using router 1941. Thanks

[@alanmercadoperez3638]

Yes you can do the same thing via FA port and it much easy

[@faheemfaansari4431]

Adnan Ali can you give me your contact num

[@kani3904]

Thank you so much for that tutorial

[@nitinmishra4482]

thanks dubey sir ....well explained

[@NetstrikersDotCom]

Thanks a lot sir :)

[@ayusuf7151]

Very well explained! is there a way I can reach you personally? I have some questions

[@faheemfaansari4431]

nitin mishra can you give me contact num

[@aredtolentino5051]

Very well explained. Thank you. :D

[@ankitgarg5979]

thank you....great tutorial

[@NetstrikersDotCom]

Ankit Garg Welcome, Thanks for your comment :)

[@faheemfaansari4431]

Ankit Garg can you give me your contact num

[@Code99849]

Thank you so much sir

[@mrs.random8095]

Thank you for the vid Sir

[@fredmills6438]

great vid. quick question: i did sh ip int brief on the router and it shows Serial0/0/1 unassigned . what does that mean because the only se ports i see are se0/0/0. I'm a ECPI Student Still Learning So bear with me.

[@prajwolniroula3912]

why we should do Router(config)#interface serial 2/0(7:25 video duration)? And what will happen if we won't do so,while configuring two router? #help

[@lohithap563]

As the router 0 and router 1 are connected with serial ports, Router(config)#interface serial 2/0 is written

[@pradeeprap2022]

Sir are you giving online training for ccna?

[@merkoszisis9927]

thank u sir u are great thanks for help!!!!

[@rixcano6936]

i sub to you man. good job

[@officialadityapowar9088]

I'm still learning now. But, i can't remember This commands would you give me like any idea or tips to remember this commands permanently.

[@Calzo89]

Well done, can you add in a cloud between routers?

[@kasunbro5576]

Thank you!

[@lasagnamamba5681]

Hi, when I click RouterO, it won't show Physical or CLI tabs, only the Config tab. Please help, thank you

[@palashpalpattuwar87]

Hello sir. nice tutorial! . I have a question. If I use a router other than the generic one, how do I run the interface serial 2/0 command? Some routers doesn't have serial ports installed in them. Do I need to add a module to my router?

[@faheemfaansari4431]

PALASH PALPATTUWAR can you give me your contact num

[@giogijon8958]

what about the switches don't they need to be configured ???

[@AmanExplora]

sir pls help me in solving this problem What is need of Router in Internet? Explain Static and Dynamic routing. Configure two routers with two host each and protocol PPP and RIP on different router with complete diagram and steps of Router Configuration.

[@yashindranawanage459]

Thank you it worked but when i make 2 LAN networks it says failed when i try to send a file over the router

[@pranamyapatil2787]

how did you come to know the serial port number for the router??

[@sharoonbhatti4386]

This tutorial is very helpful but how can i ping two routers after finishing configuration? After show ip route and than ip route. How can i ping just two routers only on packet tracer?

[@faheemfaansari4431]

Sharoon Bhatti can you give me.your contact num

[@rahulbhadane6378]

Thank you sir.

[@venkateshgoutham7535]

sir i am request timed out in command prompt.i did not recieved packets successfully.what will be the problem

[@vignesh3614]

Does the app need's internet to stimulate

[@ankitjaiswal2822]

Do you have tutorials of configuration of DHCP, SSH, Telnet , User nd password creation ??? if yes, then plz provide links... Thank you.....

[@nosherwan2089]

Thanks Man

[@Ssb9009]

clock rate what is for ? and it is necessary to add ?

[@faheemfaansari4431]

shubham singh barnala can you give me your contact num

[@2417-AliHamza]

Sir when I write interface command it give it invalid??

[@thesanskaariplayboy]

HI aaditya, your video is really great!! good job but i encountered a small problem.... i am not able to ping a pc from first network to the router in the second whereas vice versa i am able to ping please help me bro its very urgent

[@faheemfaansari4431]

Prathik Thamalla can you give me your contact num

[@emmerdoodle8517]

Thank youuuu!

[@fahadmughal9580]

How can i assigned the ip address to end devices in cli??

[@shubhammankar6270]

जब router इन्स्टॉल करते समय company leval पे command का use होता है क्या सॉफ्टवेअर से काम चलाते है

[@faheemfaansari4431]

Shubham Mankar can you give me your contact num

[@comedyvideoswitharif5295]

Thanks for the video...

[@faheemfaansari4431]

COMEDY VIDEOS WITH ARIF can yiu give me your contact num

[@gauravgurg]

How did you know the interface is s2/0?

[@sufiyanshaikh7550]

How can we check wichport router is comected

[@LetCode96666]

Try sending message packet from one network to another ! i have gone through the same process but FAILED message is showing

[@fazankhan8470]

Thanks bro

[@aparna2981]

Thanking you sir

[@BusyBrain15]

it is useful

[@kanchanwitore4737]

How to check that packets are travelling from 1 network to another

[@ravinwijekoon882]

Thank you

[@sufiyanshaikh7550]

Can u teach us ccna courses

[@ganapathynaikar1075]

Sir how to connect or configure two router using fastEthernet 1/0

[@dejavuu0090]

thx Man like!

[@mrmsali7689]

Buid one network and I can't ping one pc out of four, and I can't find the issue

[@faheemfaansari4431]

MR M S ALI van you give me your contact num

[@EMTMZ]

how can I give internet to router.

[@erickgu9504]

Tutorial de indiano, bom demais ksksi

[@rumanzahid6671]

Great

[@shreyassambare8115]

how to get serial port of router

[@jonesforever6727]

Bagaimana setting 10router jika terdapat 40 swith, jika config router di kunci dan config swith juga di kunci????

[@rjhaycostales5413]

Why there's no serial port on my router? help

[@minhaz-ul-islamridoy3682]

Why you not attached the source code?

[@sheannefrancine4957]

thanks but i thought you'd teach us how to add new ip routes :')

[@ramkesh7230]

This is very good practical how to communicate two router each other, thanks for share best practical If possible plz share contact number plzzzzz

[@nayeemkhan9479]

how i configer switch

[@harthaal-oufi2827]

thanks

[@NetstrikersDotCom]

Hartha Al-oufi Welcome, Thanks for your comment :)

[@YousCouz]

Jij bent mijn held hoor! Je klinkt als mijn pa :-) XDDDDDDDDDDDDD

[@YousCouz]

houd je bek man

[@SHUBHAMSINGH-gv1ut]

Interface serial number kha se likh rhe hai

[@NetstrikersDotCom]

[@sanjum9434]

I came for router options not showing, i just neeed to press enter to get that lol 😁😂

[@kakaballu1]

why you not implement ip routing ...this is not beneficial

[@chaitanyanandamuri1510]

sir 1s send commands step by step

[@Deeeeeead]

Come si fa il NAT??

[@Pomo_lori]

bella frate

[@NetstrikersDotCom]

+Lorenzo Urru Grazie :)

[@solymar552]

u hit your keyboard so hard

[@SGCStylezZ]

It's funny how I search for "not durdurdur" and still get "durdurdur". Fuck google.

[@iKlau-xz]

Thanks! But, how i put password and login??

[@NetstrikersDotCom]

+iKlau xz Thanks If you want to set password then type the following commands.. Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)#line con 0 Router(config-line)#password cisco Router(config-line)#login Router(config-line)#exit

[@prosperwilliam1358]

unajua sana

[@masengeshoseverain250]

cisco

[@mert-erenincedal7267]

foreigners...

[@bassammz]

هندي واضح