How To Design Automatic Generation Control of Two Area System Using MATLAB/SIMULINK (Part-1)

[@neenoo12345]

رزقك الله جنة الفردوس الأعلى وخير الدنيا والآخرة Thank you!

[@DrJALAGHARI]

Thanks for the compliments.

[@mahinstitute3418]

Jazaak allah. Definitely very helpful

[@DrJALAGHARI]

Thanks for the compliments.

[@igorbigchlen5812]

Thank you very much … you are a star 🌟

[@DrJALAGHARI]

Thanks for the compliments.

[@abimagodfrey3239]

Hello Sir, firstly i would like to appreciate you for this lecture. Would you kindly clarify the details you put in the step input signal for Final value. And also elaborate how third power plant would be added to the system. Thank you.

[@DrJALAGHARI]

Thanks for the compliments. The details can be found in hadi sadat book power system analysis chapter 12.

[@Nodommify]

hello Sir, please can you help me please. i have to simulate a single- node power system with 2 turbine- generators (power plants) supplying one load and observe the frequency behaviour after the loss of one of generators(a t=5s)

[@DrJALAGHARI]

Thanks for the comment. For this topic, first try to find any research paper closely related to this topic. Then try to reproduce it in the MATLAB. Otherwise, it will be difficult.

[@Nodommify]

@@DrJALAGHARI please sir could you make a video on it?

[@incurzyou4560]

@Nodommify I have the same case as you and I'm stuck please can you provide any help

[@NehaSharma-it2ld]

I got a problem while solving this problem in the step block it says u can't set step size to hundred .....not able to get the waveform in the scope

[@DrJALAGHARI]

Thanks for the comment. Which Matlab version you are using?

[@tahirusman1129]

wonderful, jazak Allah khair

[@DrJALAGHARI]

Thanks dear for the compliments.

[@DrJALAGHARI]

Thanks dear for the compliments.

[@kiranmaichigurupati3378]

Very well explained. Thank you!

[@DrJALAGHARI]

Thanks for the compliments.

[@samikshyapoudel9450]

Sir what if the base MVA is different and we have to perform base conversion ? Suppose area 1 has Base MVA of 1500 and area 2 has base MVA of 100000. Do we have to convert values of "R" and "D" to a common base ?

[@DrJALAGHARI]

Thanks for the comment. For details, kindly go through the power system analysis book by hadi sadat chapter 12.

[@muhammadsalehabbasi1595]

Well explanation thanks sir for your sincere efforts

[@DrJALAGHARI]

My pleasure.

[@TheDcandon]

Muchas Gracias Dr.

[@DrJALAGHARI]

Thanks for the compliments.

[@undintiakhilkumar5863]

sir what is the graph about sir what is in xaxis and in yaxis i mean frequency and time or something other

[@DrJALAGHARI]

Thanks for the comment. Yes. It is frequency over time. At x-axis it is time and at y - axis it is frequency

[@undintiakhilkumar5863]

@@DrJALAGHARI tqq sir doo all graphs in these video are frequency over time?

[@DrJALAGHARI]

@@undintiakhilkumar5863 I don't remember exactly. Some graphs are of power and some are of frequency.

[@undintiakhilkumar5863]

@@DrJALAGHARI sir plz wil you tell me the exact about the graphs actually iam doing my project on this soo plz wil you tell me sir

[@DrJALAGHARI]

@@undintiakhilkumar5863 Thanks for the comment. I think i have explained in the video about each graph. You may also see hadi sadat book power system analysis chapter 12. This example is taken from this book.

[@qalbaldinahmed8156]

Thanks bro.. plz I need expalin about connect two area power system with PI I need it necessary

[@DrJALAGHARI]

Thanks for the comments. Just watch the second part and then replace the integral controller with PID controller. In the PID vontroller, put the input of D to zero

[@HosamMostafa-h7s]

Please What version of Matlab do you use?

[@DrJALAGHARI]

Thanks for the comment. I use MATLAB version 2017a.

[@asimmohammed9923]

Assalamalikum....waiting for more lectures on load frequency control matlab modelling....may be some optimisation technique

[@DrJALAGHARI]

Wa'alaikum salaam ok i will try to make videos on optimization technique.

[@kermdncer9981]

Hello, Thanks for your video. How can we convert the simulation to m.file? Do you know that?

[@DrJALAGHARI]

Thanks for the comment. I don't know any such method

[@asimmohammed9923]

Very well explained sir...

[@DrJALAGHARI]

Thanks for the compliments.

[@gauravbhatt6882]

How many states are in this ? Like X1,X2...... Further

[@DrJALAGHARI]

What do you mean by states? Ithere are two areas.

[@aliabdelrady6482]

Thank you very much, how to download Matlab Simulink for Hadi Saadat

[@DrJALAGHARI]

Thanks for the comment. Send email to [e-mail] it will be sent to you.

[@maharamoh93]

I want a model of two circuit transmission line with a fault in one of the circuits

[@DrJALAGHARI]

Ok i will try to make video on this topic.

[@maharamoh93]

@@DrJALAGHARI thanks alot

[@seidaabdulqadir6591]

thank you sir for your supportive videos,could you show us the simulation on impact of load behavior on transient stability and power transfer,thankfully

[@DrJALAGHARI]

Thanks for the compliments. Transient stability is another important field and requires deep study. It will take time for me to work on this topic.

[@seidaabdulqadir6591]

@@DrJALAGHARI okay sir, I will wait for your lectures, thank you

[@fashiontips5322]

I am doing agc with a single area system. But my output is not correct. Can you help me with this ?

[@DrJALAGHARI]

Yes sure why not?. What problem you are facing?

[@fashiontips5322]

@@DrJALAGHARI i don't get my output. While i am doing this. I put all values and blocks correctly in Circuit. But when i run the simulink it's output is totally different then it should be.

[@DrJALAGHARI]

@@fashiontips5322 what should be the output? And what is your output?

[@fashiontips5322]

@@DrJALAGHARI as it shown in your video. My ouput is same as your ouput. Which is shown in this video.

[@DrJALAGHARI]

@@fashiontips5322 if output is same then what is the problem???

[@undintiakhilkumar5863]

Sir it is thermal power plant or hydro the sytem

[@DrJALAGHARI]

Thanks for the comment. I don't remember exactly. But i think it is thermal. You may confirm it from hadi sadat book.

[@danoku5582]

Dear sir. I want to ask how do you determine your nominal frequencies? e.g how do you predict the nominal frequency is operating at 60HZ?

[@DrJALAGHARI]

Basically this model is taken from power system analysis book by hadi sadat. In this book, all examples have nominal frequency of 60hz.

[@thehaseeb9136]

Sir can we do this for reactive power compensation in static VAR compensation in Transmission Line?

[@DrJALAGHARI]

Thanks for the comment. For this purpose, try to follow any research paper closely related with this topic for better understanding.

[@muzafarhussain6583]

Very Nice Sir

[@DrJALAGHARI]

Thanks

[@DrJALAGHARI]

Thanks

[@eengpriyasingh706]

dont you need initialisation of the system?

[@DrJALAGHARI]

Thanks for the comment. I am sorry I couldn't understand your comment. This example is taken from power system analysis book by hadi sadat chapter 12

[@NisarAhmed-qw5he]

Thanks sir❤️

[@DrJALAGHARI]

Thanks

[@Electrical.Engineer730]

Bravo sir

[@DrJALAGHARI]

Thanks

[@nadiabenalia-x3s]

thank you

[@danoku5582]

Dear Prof. I have a question. I was trying to practice your model, however using but 100MW for change in load at Area 1. When I showed it to my Supervisor a Prof. He suggest that the model does not show the Pref. i. e there is no ref. Power value inputed on the feedback. Pls can you explain why?

[@DrJALAGHARI]

Thanks for the comment. You may kindly go through hadi sadat book chapter 12 for further explanation.

[@danoku5582]

@@DrJALAGHARI Ok Sir. Pls which of the edition do you recommend. I have seen the second edition on Ebay but I am not sure if that covers all the chapters?

[@DrJALAGHARI]

@@danoku5582 this book is freely available on internet. You may download it.

[@danoku5582]

@@DrJALAGHARI Thank you sir

[@HosamMostafa-h7s]

Please What version of Matlab do you use?

[@DrJALAGHARI]

Thanks foe the comment. I use MATLAB version 2017a.