How to Determine Weld Sizing and Analyze Strength with SOLIDWORKS Simulation

[@gregoirearsenault7336]

Alignex, Inc, Is there any possible way to weld to solid?

[@catmechanic1261]

Following, but when we get to 4:54, I click on tube and I get message: Edge weld connector should belong to faces or surface bodies or sheet metal bodies - and then it won't let me select a surface. What have I done wrong. Thank you

[@danielmichela5622]

I have the same problem. Did you find a solution for this ?

[@LmTrn]

@@danielmichela5622 I'm having the same problem. Did you find the solution for it?

[@JamesClarke1]

Not sure if you will see this but how do youni terpret the results from that solid nodel of the weld? Thanks

[@BryanNickel_Hydroplate]

What strength is defined by solidworks' term "weld strength" Is this the weld material's yield strength, ultimate tensile, shear?

[@rambo9857]

Thank you for you tutorial Bro, good job!!!

[@belguithmonir4826]

first of all thank you for this tutorial but if you don't mind, can you advice me i want to do simulation for polypropylen tank welded by the polypropylen too if i choose "costum steel", would this give me right results for the estimation of the weld size and if yes how to choose the value of the weld strength parameter (elasticity limit or tensil limite ..) cordially

[@dellpi3911]

kzbin.info/www/bejne/f5LRmIt3eKuKapo.

[@eyupfirataydin4563]

I cannot make welds between solid bodies It is asking me to select surfaces and shel bodies only modelling the weld is time consuming how did you make it in the video?

[@mystrusaiza]

How about weld FEA with root gap? Is this possible in Solidworks simulation?

[@eyupfirataydin4563]

how can I make welds to the surfaces which are not perpendicular

[@mat4i]

Good job, very helpful!

[@falcon26r87]

This is a fantastic video! Thank you for Posting Tim

[@peoperreault5911]

Very clear and complete! Thank you.

[@catmechanic1261]

Let's say I have a large fillet weld, I have the initial root pass, then two cover passes, then 3 cover passes on top of that. Where in Solidworks do I replicate that sort of weld process? Thank you.

[@impactodelsurenterprise2440]

U just annotate the weld type, size, and process, and let the certified welder do his thing. Like annotating for heat treatment on a part you only note the hardness required, you don't try to teach the heat treaters what temperature to hold, time, etc.

[@davabran]

Great video Thanks!

[@chetnaprajapati9483]

how to sync two circle example:- one circle dia75mm and secound circle dia1000mm dia1000mm (1000mm-100mm=900mm) so change dia 75mm change (75mm+100=175mm) mins i one circle dia minuse so secound dia pluse is value how create बहुत बढ़िया पर मुझे ऐसा काम कुछ इस तरीके से करना हो तो कैसे करे कृपया बताये जैसे के एक circle 75mm dia का हे और दूसरा circle 1000mm dia का हे अगर में इन दोनों में से किसी की भी साइज़ बदलता हु तो वो एक दुसरे में pluse minus खुद्ब्खुद हो जाये जैसे के अगर में 75 mm dia में 25 mm जोड़ता हु तो वो dia 100mm हो गया पर जो दूसरा dia जो 1000 mm का हे वो 975mm खुद्ब्खुद हो जाये बस ऐसे कोई भी एक dia अगर pluse होता हे तो दूसरा dia खुद्ब्खुद minuse हो जाना चाहिए और कोई भी एक dia minuse होता हे तो दूसरा dia खुद्ब्खुद pluse हो जाना चाहिए हा पर जितना हम pluse या minuse करते हे उतना ही value एक दुसरे dia में pluse minuse होना चाहिए कृपया करके ये बताये ये कैसे हो सकता हे solidwork में ?

[@noznip2008]

thank you !

[@MAMotinSobujsobuj23]

Thanks

[@surry99]

For the excavator example, why is g = - 656.574 in/s^2?

[@TheCuriousOrbs]

Off-world engineering is hard, right. (should be 386.2 in/s^2 for Earth)