How to do Valve Clearance Check and Adjust Toyota Camry. Years 2000 to 2021

Cómo comprobar y ajustar la holgura de las válvulas en un Toyota Camry. Años 2000 a 2021
How to do Valve Clearance Check and Adjust Toyota Camry. Years 2000 to 2021
Do service within every 70 000 miles or 100 000km
Disclaimer:
These videos are intended to offer general information working a car and tools.
The Peter Finn have used best effort in creating the video. No liability can be accepted by the author and publisher for any expense, damage or injury caused by any errors in the information given. In no event shall author be liable for any direct, indirect damages or loss of profit by you or any third party.
Due to factors beyond the control, I cannot guarantee against improper use or unauthorized modifications of this information. Peter Finn assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. I recommend safe practices when working on vehicles and or with tools seen or implied in this video. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Peter Finn.
Work carefully and safely. Also avoid accidents.

[@coreyandnathanielchartier3749]

Very useful video, even to a old pro. Ignore the ignorant comments from some of the trolls below who barely have a command of their own language, let alone another. BTW occasionally, you get lucky and can swap and switch shims around on the motor and not have to buy any. And for the uninitiated, too much clearance is far better than too little. You can look at the lobes when you pull the cover, and the ones that are shiny all the way around are usually too tight. Another sign is a engine that develops a miss as it warms up.

[@leonardlewis5586]

Where I'm from we call people like you a beast in these streets!

[@ditr257]

Excellent adjustments, measurements and mathematical calculations, Peter!

[@mrayco]

Thank you for sharing us this knowledge

[@maxbagard8007]

Bonjour, merci pour la vidéo j'ai appris beaucoup de chose

[@native167]

Thank you for this very informative good video sir ... Much needed

[@josefranciscoesquertalaman3827]

Like !!!

[@kgb0070]

POSITIVO E OPERANTE PETER E BOM TRABALHO !

[@braedoncar6436]

Amazing!! Thankyou

[@vaman86]

Thanks Peter …… Excellent description of a very complicated subject ..also wanted to ask about the hook bolted to the back left side of the head…. Is that for pulling the moter or just the head? 😊

[@yusufaras9066]

Hi Peter. i have 2017 corolla 1.33 vvti with no LPG. its only at 24000 km. But is it possible that valve problem issue occures. Vibrating idle while engine is hot, sometimes late start-up engine with white smoke from exhaust. Everything controlled, the lastly is stay valve clearance. Can you give me some info about it. Thanks !

[@arnaldoventura2]

Hello, very well explained, I want to know if you can tell me how to calibrate and if you give me the values ​​for each exhaust valve as for intake of this three-cylinder TOYOTA YARIS second series 2nd XP9 (2005/2011)

[@bobwa399]

Is it ok to set tappet loose after a fresh engine rebuild? the idea is to let valve seat to adjust properly cause they were built new too.

[@davea5150]

Hi Peter!! I was wondering what you think about if my 2000 Toyota Camry 2.2l engine with 202k miles runs excellent and is very quiet should I bother with checking the valve clearances? I just put a new valve cover gasket on. New fuel filter,new air filter, new spark plugs,new PVC valve,and what really made so much difference in performance and it stopped the miss was a original Toyota Map Sensor. It runs PERFECT. Wish the body was nice. Lots of dents. I got it this way three years ago for a thousand dollars. Now trying to figure out where to buy cheap but goot tires? Any ideas? 205/65/15. Thank you Sir 😊👍👍👍👍.

[@lensmanicfeleven1847]

what kind of engine has the cam lobes both opening/closing at same time?...

[@dowhatyougottado916]

When you install thinner lifter wouldn’t that increase clearance? When do you add shims?

[@platinumGEE916]

@ time stamp

[@user-ql2bp6ru8n]

How are you sir, thanks for sharing this information . So what can be best clearance sizes Ex and in for 3L

[@iantacbobo3854]

Sir what is the valve clearance for Toyota vios 2nz clearance for inteck & exhaust

[@bobespnza-la7030]

How would I know if I need to perform this Valve Clearance ? Thank you