How to Draw Slope from Differential relay setting

How to Draw Slope for Differential relay
i have taken relay setting basic on that i have drawn slope.
relay setting are.
ID pickup = 20%
Slope 1= 30 %
slope 2 = 80 %
High differential = 800 %
End section 2 = 1.5
by using this value i have calculated Slope fully.

[@djeev1]

Wonderful explainations and very clear thanks you. I think no one on internet is explaning like you. Please keep it up with all other protection relay functions. Many thanks.

[@baranitech1026]

welcome and thank you

[@bikramdas9770]

You explanations are too good. Thanks for sharing knowledge especially in a field where free knowledge is hard to come by.

[@divahars5638]

Exactly said

[@thebeardedman8356]

Very helpful and useful for those tester new in this field. Thank you very much. 👍👍

[@baranitech1026]

Very welcome

[@tusharshinde8228]

Very nicely explained sir... thank u so much sir..keep posting videos like this..

[@_Al-Furqan_]

U r the best bro, expecting more videos about relay testing from u. Thank u bro.

[@baranitech1026]

welcome bro

[@abudhakir9403]

Very nice explain... thank u so much i never forget Thanks lot

[@jaynandan9937]

Sir your knowledge is excellent

[@divahars5638]

Very nice explanation keep it up sir👏👏

[@baranitech1026]

thank you

[@mr.biplob3795]

Awesome boss

[@Sarchitta]

amazing! very nicely explained.😀

[@baranitech1026]

Thanks a lot 😊

[@shahzadhashmi1454]

thnx for sharing knowledge ... appreciate it really ...

[@baranitech1026]

Thank you

[@engrnazmulkhan]

Thanks for helping everyone

[@shihabahmed5399]

Thanks for helping.

[@KundanKumar-vj5ez]

Excellent anna.... you are the best on KZbin 🙏

[@baranitech1026]

Thank you so much 🙂

[@sauravmazumdar5369]

Excellent...

[@baranitech1026]

thank you

[@Mumbaindianzzzzz]

Great explanation sir......

[@baranitech1026]

thank you

[@ttlstark2292]

Awesome minded

[@baranitech1026]

thank you

[@emmanuelabunyang8831]

Thanks for your incite full work

[@baranitech1026]

thank you

[@surendrakverma555]

Excellent lecture Sir. Thanks 🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏🙏

[@baranitech1026]

welcome most

[@venkatyalamati3285]

Thank you so much sir... Plz share video on distance relay settings and its characteristics.

[@baranitech1026]

sure ..

[@souvikdasgupta6363]

Can u give me idea about what happen when fibre communication fail between differential relays, I mean emergency over current mode

[@ritesh8353]

How to calculate Relay pickup current in differential relay with zero sequnce elimination in Dyn11 transformers?

[@ullasan1905]

Useful

[@baranitech1026]

thank and welcome

[@naveen13111]

Thank you for the vedio sir. Can u clarify what is the basis for setting ES2 as 1.5 ??

[@baranitech1026]

end of slop 2 it was setting given in relay

[@mr.biplob3795]

Singal phase slope testing i was try but as per calculation not match with slope 40% & 80% in abb Ret670 relay,please explanation what is the reason for singal phase slope testing

[@juhaanable]

First i would like to appreciate the way u explained, sir Es2=1.5 can u tell how pls i need ur response back thank you

[@ravindrayogi3196]

Among of all video finally find reason why we use k1 k2 is1 is2

[@baranitech1026]

your most welcome

[@pgopalakrishnanmkp]

How did you find or assumed ES2=X3=1.5?

[@baranitech1026]

it will be given by relay setting value itself

[@aftabraj1865]

Please make a video on how to test P643 relay with omicron kit

[@baranitech1026]

soon i will make for you.

[@electricaltech4u45]

Well done bro. I am very confuse i try to configure my differential relay settings but again and again error come in micom p632 🤪🤪

[@electricaltech4u45]

Ok bro i will try again

[@deltech9947]

Hii bro finding ES1 how we are assuming that 0.3 value

[@baranitech1026]

ES1 should not assuming we have to check in manual . in manual if not mentioned then we have to use pickup % divide slope1

[@soumya2221]

Sir how to calculate id - 0.2pu,,,i. E what is the actual value of id in terms of actual current

[@baranitech1026]

= full load current / CT ratio X 0.2

[@arifmehmud5677]

why we use off plus time in under voltage relay timing test????

[@baranitech1026]

sorry i don't know . i try to get answer for your question.

[@yahiabouchene239]

Thanks

[@baranitech1026]

welcome

[@F13TUN]

Tanks sir .Can u group in one video the parameters for drawing slopes for different types of relays abb ret 670 ,micom p632 or 642 sel 787 Siemens 7ut ..

[@baranitech1026]

i will try

[@thewelcometodark]

Sir, thank you for ur video🙏 actually 1.5- 0.66 = 0.84 but u wrote 0.94.

[@thewelcometodark]

@@baranitech1026 sir, neenga Tamil la program pandreenganu nenaikaren. Good initiative sir. I learned this graph bcs of u. Thank you very much sir.

[@powertech5055]

How can get Y4 value during last stage

[@baranitech1026]

y4 It has to given by client

[@swaransingh1690]

Very good. Thanks for the video. But I think when slope 1 is 30% and slope 2is 80% then curve slope for slope 2 should be steeper than slope 1, but it is less steeper than slope 1. Curve shape should have been steeper for slope 2 than that of for slope 1.

[@baranitech1026]

Actual its demo value if i make next video related with slope i will see this also. thank you for your command.

[@jaynandan9937]

Sir differential relay. What is pu please give the settings calculation. YND11 X-mer, 400kv, 24kv, LV CT ratio-12000/5, HV CT ratio - 1000/1, X-mer % impedance 15, relay micom 643,

[@jayamurugantceng6851]

Y4 value where i get

[@baranitech1026]

its high differential value

[@subrahmanyamgokavarapu7970]

Hello sir.. 10 % , 20 % of what ?? could you please clarify

[@baranitech1026]

at what time on video you have doubt please tell me

[@annamalainarayanan1219]

Please make tamil version

[@annamalainarayanan1219]

Thanks

[@karthikscorpion6627]

UR ASSUMING SLOPE 0.3,WHY IT SHOULDNOT .45

[@baranitech1026]

it can be also its just for explanation

[@mr.biplob3795]

Y4=8how you getting? Pls tell me

[@mr.biplob3795]

@@baranitech1026 id>> =8 ( High set)

[@tufailalam6438]

@@baranitech1026 sir. If Y2=20%=0.2 then why not Y4=80%=0.8 .???

[@sabumtsabu]

@@tufailalam6438 It's not 80%; it is 800 (eight hundred) %.That is why it is 8.

[@satyarout9377]

Video hindi main hoto to easy to understand hotaa

[@darveshable]

@@baranitech1026 sir please upload how to calculate setting of differential relay...

[@manoharanvaradharaji]

1.5-0.66=0.84 not 0.94

[@baranitech1026]

sorry for the mistake