How to: Fix a Nitro Engine that is locked up or will not turn, Engine is frozen, .. hard to turn.

  Рет қаралды 24,274

Gotta Know Joe Hobbies

Gotta Know Joe Hobbies

3 жыл бұрын

*** WARNING *** WORKING WITH ANY FUEL SHOULD BE DONE OUTSIDE USE EXTREME CARE WHEN WORKING WITH ANY FLAMMABLE LIQUIDS This simple fix can be used for all nitro engines that are locked up due to dried fuel oil. Not hard easy to do. GOTTA KNOW JOE HOBBIE in Spring Tx
Google us

Пікірлер: 87
@bkahiv
@bkahiv Ай бұрын
i unfroze my RC plane nitro engine using your method but using WD40 and it worked like a charm. TY
@adr8nalin73
@adr8nalin73 Жыл бұрын
By far the best explanation, thank you sir
@leonelcardenas-sj9fo
@leonelcardenas-sj9fo 5 ай бұрын
We have a saying in spanish "mas sabe el diablo por viejo que por diablo" this is the perfect example, didn't translate it cause translations always suck,thanks a lot man for this video...!!!
@biogons14
@biogons14 Жыл бұрын
This method has worked for me with a Super Tiger engine from the 70s. Instead of fuel I used isopropyl alcohol, and light oil when was unseized. But, taking many precautions; open window, gloves, protective glasses and mask. Very thanks.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
I'll need to try that
@dmrcflyr2
@dmrcflyr2 3 жыл бұрын
3-in-1 oil works every bit as good, is more readily available than glow fuel, AND cleans any rust that might be on any steel parts. It is MUCH less expensive than hobby after run oil. I always use oil and heat to loosen a gummed up engine, but I NEVER use a vise to hold an engine. Heat resistant gloves and a prop installed on the engine is all that is necessary to turn it over.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 3 жыл бұрын
Great point!
@savagenoob
@savagenoob 2 жыл бұрын
Clamping the engine in a vise where he did will do absolutely no harm to it. That's where its mounted to the chassis and is designed to hold the engine in place.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 2 жыл бұрын
Nitro should be readly available if you own nitro engines I'd guess. The 3n1 did not cut the gum as well imo..but my technique may be wrong
@RC-Flight
@RC-Flight Жыл бұрын
Dave thanks for calling this engine and fuel glow, it’s not a nitro engine or nitro fuel is it!
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
@@RC-Flight just slang.
@thatracer05
@thatracer05 Жыл бұрын
Thanks for this! Huge help. Worked like a charm. Hoping my truck starts today!
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Glad it helped
@w.w.harbaugh8046
@w.w.harbaugh8046 2 ай бұрын
Great advice, thanks. Keep up the good work.
@officialelysium4821
@officialelysium4821 Жыл бұрын
Thanks this helped me with my tmaxx 3.3
@letusshare5316
@letusshare5316 Жыл бұрын
Thanks for the useful tip.
@stonewallsaucedo5613
@stonewallsaucedo5613 Жыл бұрын
Yeah that marvel mystery oil is a miracle this old dude would put it on and in his motors and tools and yeah it's amazing shit specially when you let it soak in over night a nut you can get out or bolt off next day that bolt or nut will come out like butter
@ifly65
@ifly65 Жыл бұрын
Nice thats easier than the slow oven method.
@josedm2009
@josedm2009 2 жыл бұрын
OMG THIS WAS AMAZING THANK YOU THANK YOU THANK YOU!!
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
no worries
@bryanmillers3231
@bryanmillers3231 2 жыл бұрын
Thx I just did it to my taxxax and it worked perfectly I just used 3 in 1 oil and a heat gun
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 2 жыл бұрын
I'll need.to try 3n1
@briangleason5597
@briangleason5597 5 ай бұрын
Thank You for you're video.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 5 ай бұрын
Thank you for watching. Google us you can always call for friendly advice.
@WarbirdPylonRacer
@WarbirdPylonRacer 3 жыл бұрын
Great video! Thank you!
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 3 жыл бұрын
no worries see our others and please subscribe... need 600 more so we can post live from phone
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
MARVEL MYSTERY OIL I speak as well as a drunk worm with itchy feet... ?? Lol, I don't know what this means either it just came o me.
@ashermorales8276
@ashermorales8276 2 жыл бұрын
I had an old novarossi .12 and the bearings and the crankshaft were super gummed up. I took the thing apart, popped out the crankshaft and used a tooth brush and some break cleaner to scrub off all the gummed up oil and completely cleaned out the bearings. I didn’t worry too much about the piston sleeve and rod because I had a spare set that was brand new. Once it was all clean I heavily oiled everything with 3-in-1 and it was basically brand new
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Always good to wash out the bearings with solvent add oil until smooth and free
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
I've used s lot of stuff never brake fluid. Probably cause u hate the smell and fell of the stuff and I seem to always get it on my lip and taste it for 2 days after. Lol but I will try it once .. brake fluid eats the hell out of paint that's for sure. This method is really used more to get the. Unseazed so you can tear em down . Ill need to do a more detailed video on a full clean.. and rebuild. If its cool I may use your idea as well To see how it works..im very interested in trying it now.. I could relax if I wasn't so curious lol
@tenlittleindians
@tenlittleindians Жыл бұрын
@@GottaKnowJoeHobbies He didn't use brake fluid he used brake cleaner. I'm curious too if it will cut old dried up castor oil. Carb cleaner should be safe as most model motors and carbs are aluminum. Again; I have no idea how effective it is against old castor oil. The old timers used to recommend putting the motors in an old pan of antifreeze and heating it up on a stove to clean them.
@brucerumrey8894
@brucerumrey8894 Жыл бұрын
Great video that what I do
@stephenparkins3552
@stephenparkins3552 Жыл бұрын
I do this quit often with engines I get on craigslist. I use mystery oil, soak the cylinder and the carb over night. Then I use my heat gun. Get it good and hot and it will break free every time!
@williambryant6654
@williambryant6654 3 күн бұрын
Marvel mystery oil ,great stuff for after run and storage.
@d.haroldangel241
@d.haroldangel241 9 ай бұрын
GLOW ENGINES is the name. They are not all necessarily run with nitro(methane). It's called GLOW FUEL (sometimes containing different nitromethane percentages.
@mdrc3288
@mdrc3288 Жыл бұрын
Great technic!!!Never thought that this could be possible without removing the head!!!🙂👌⭐⭐⭐⭐⭐
@av8or971
@av8or971 2 жыл бұрын
less sounds effects.. lol but great vid. i will try that tonight
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Old men just makes a lot of nosies lol
@phobicwhistle2182
@phobicwhistle2182 Жыл бұрын
Goofy ahh sound effects to be exact lol
@Glowrc
@Glowrc 11 ай бұрын
Just bought 2 vuntage nitro trucks....will try this
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 11 ай бұрын
Did it work?
@Glowrc
@Glowrc 11 ай бұрын
@@GottaKnowJoeHobbies no the engines are blown 🙃
@bertkoerts3991
@bertkoerts3991 Жыл бұрын
Enjoyed your video very much. Question: is there a fire risk with the heatgun? This is a diy heatgun, not a hairfohn right? Tnx 👍😊
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Yep. it could sir... but. I've been doing it for years and common sense or lack of it, has kept all my fingers attached..6 right? he mutters and counts under his breath slowly "7,8,9,....no 10 I'm sorry"... lol .... sparks are not desired.. we just want to warm the cases... Don't use open flames Ya Gotta remember, NO LEAD in Soldering wire works poorly, The "NEW Safer" glues don't stick well, and Wd40 will not cure aching bones since the DMSO was removed. POINT IS if it's "safe" or Safer" or better for you .... things that seem to taste bad. or fun is not as fun, worked well. now don't work, or is now illegal ;) ( I must write this is a parody so as not to hurt anyone's feelings that do not understand the pun.) Please, folks... I do not want to enter a BIG controversy about this. it works for me and has worked for many. If you are dangerous with an ice cube, hammer, or spool of thread it may not be for you,,, lol Bert this is not directed to you brother. I can just see it coming though.. lol trying to get in front. Your question is valid And yes It could... but my highly uneducated non-existent field testing has proven, chances are slim to none but everything is possible. Hope it helps
@jmiii6277
@jmiii6277 Жыл бұрын
Gonna try this on two I haven’t ran in 6 yrs. What process if any on running engine again … break in etc ?
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
q
@davidpalacios1017
@davidpalacios1017 Жыл бұрын
Hey joe, I have a question you may be able to answer. I bought a new Kyosho and the engine seized on the first idle, I unseized it with a heat gun and it locked up again on idle. When I purchased the buggy it was very hard to pull the starter without unscrewing the glow plug. I unseized it and added mystery oil now. Question is any idea why it locks up when the engine gets warm?
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Could be something up...but it should turn freely with no plug. And bir of resistance on TDC top dead center during to the squish. The narrowing of the sleeve .. you may be running too little oil also. I would reach out to manufacturer and or take it to a shop so they can look over all the possibilities before you fry the engine
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
I wish I had the definitive answer I just don't think there is one
@David-sw3on
@David-sw3on 2 жыл бұрын
I like the 60/40 tranny fluid-oil concoction... This may be a stupid question, but What is Marble mystery oil...Is that what you called it?🤔 And PS awesome video I definitely learned a thing or five. but the best part of all was your audience.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 2 жыл бұрын
Marvel Mystery oil all auto shops have it Glad this helped .. call us if you ever need a hand ... or a deal
@cornpopfan319
@cornpopfan319 3 ай бұрын
My engine will rotate half way and then compress and stick while the plug is in. If I take it off, it’ll turn over. I’m new to glow engines so is there something I’m doing wrong here? I’ve already primed it and put the igniter on a brand new plug, but the issue still persists.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 3 ай бұрын
There is a thing called vapor lock. You've got to watch out for. That's when you get fluid and door gases on top of the piston, which hydraulically it combust a piston. Besides that, you want it to turn freely with the plug out. But when the plug is in, that's your compression that makes your engine run
@cornpopfan319
@cornpopfan319 3 ай бұрын
@@GottaKnowJoeHobbies thank you so much. I cleaned and sanded the cylinder thoroughly and the underside of the piston, re-oiled everything and then got new fuel lines. It started for about 2 seconds and now it just hisses and sputters. Definitely some progress
@Workerbee-zy5nx
@Workerbee-zy5nx 6 ай бұрын
Wd 40 also works
@dynevor6327
@dynevor6327 16 күн бұрын
Just "freed up" 7 engines 2 and 4 stroke using WD40. Engines had not been used since the mid '80s and all came free immediately. The hardest part was removing the barrel from the carbys. One 4 stroke took a little time to free the cam followers but slow and steady.
@Workerbee-zy5nx
@Workerbee-zy5nx 16 күн бұрын
@@dynevor6327 PB Blaster oil works great.
@dynevor6327
@dynevor6327 16 күн бұрын
@@Workerbee-zy5nx Not where I am.
@TheCecil64
@TheCecil64 2 жыл бұрын
What if you put the nitro in an old pan heated up on the stove - then let it soak for a while ?
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 2 жыл бұрын
We do it as well on real bad ones but you must remove all the plastic and orings 1st..becareful of plastic carbs
@FindShindoHere
@FindShindoHere Жыл бұрын
Kahboom
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
But don't heat up the fuel in a pan NEVER get around open flames. OLD into will blow. We stay below flash point and no flames with gun
@afshinpishehvar7815
@afshinpishehvar7815 2 жыл бұрын
When we buy an old nitro engine, how do we know if it works clockwise or counterclockwise?
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 2 жыл бұрын
Car or plane
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 2 жыл бұрын
Most all engines turn counter clockwise if you run into a clockwise turning engine it's rare. Fe 350 kawasaki turn clockwise and it cost me a tine of cash youbjust do see them so you don't need to look for them really
@tobydyes
@tobydyes Жыл бұрын
Does that work for all nitro motors or just airplanes
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
all
@davidrichardson4779
@davidrichardson4779 3 ай бұрын
Rislone motor treatment oil is v good oil also & cheaper....
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies 3 ай бұрын
Thank you ill try it sir
@localboyn2deep146
@localboyn2deep146 2 жыл бұрын
That's why if you're storing, put after run oil 🛢 in it, or 3- in 1 oil 🛢 remove all the nitro fuel first....🤦‍♂️🙄
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Not everyone puts up engines properly this is how you remedy others lack of care. 🙄
@craigwilliamson4345
@craigwilliamson4345 Жыл бұрын
Just as easy to pop it in a boiling pan of water for 15 minutes
@tbd-1
@tbd-1 5 ай бұрын
Just did this to an OS 40 SF. Once the water boiled I took the pan off the stove and dropped the (complete) motor in the water. After a couple minutes I drained the water, wrapped a towel around the motor and broke it loose with a pair of channel locks on the thrust washer. It offered little resistance and the whole process took less than 10 minutes. A good flushing out with WD and MMO and it's ready to bench test.
@FindShindoHere
@FindShindoHere Жыл бұрын
Ooooh ooooooo[ooh unh lol
@mariodelgado9729
@mariodelgado9729 Жыл бұрын
Why not use a fire hose to pour on the nitro, it would be smaller that that hunk-of- squeeze bottle!!
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Its what I could steal from the wife. lol
@mariodelgado9729
@mariodelgado9729 Жыл бұрын
@@GottaKnowJoeHobbies Yeah, tell me about it!
@WayneCook306
@WayneCook306 2 ай бұрын
They are Glow engines nitro is only an additive, not an engine name.
@jeffreyspringstun6546
@jeffreyspringstun6546 Жыл бұрын
Yeah, let’s poor methanol, nitro and oil all over the place and then add a source of ignition to the mix, makes perfect sense to me. Heat and oil, NO FUEL !!! This is a terrible idea, don’t do this unless you’re ready for the burn ward. Be careful what you glean from someone who’s been doing something for years and never had anything bad happen, YET ! No, don’t do this.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
Old nitro that's sucked up humidity for for months sitting around to shop is near impossible to catch fire..ill need to make a video on it one day. 30 plus yrs at this I've never has an issue. And it's only a table spoon or 2 at best
@jeffreyspringstun6546
@jeffreyspringstun6546 Жыл бұрын
@@GottaKnowJoeHobbies No offense Intended Sir, you cannot debate the logic of my point, I must have missed the part where you said that bottle of pink liquid was non flammable. Old schooler myself, simply trying to protect you and your watchers, always think about the next 15 seconds when performing a task. Be safe.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
@@jeffreyspringstun6546 no offense taken my brother
@robjames5623
@robjames5623 Жыл бұрын
Stupid sound effects just spoil it.
@GottaKnowJoeHobbies
@GottaKnowJoeHobbies Жыл бұрын
I did use as many as i have in past.. Your right though too many I do agree sir..
RC Nitro Engine Piston and Sleeve Resize Tool.
17:44
EBMods
Рет қаралды 11 М.
La revancha 😱
00:55
Juan De Dios Pantoja 2
Рет қаралды 70 МЛН
Sprinting with More and More Money
00:29
MrBeast
Рет қаралды 188 МЛН
Khóa ly biệt
01:00
Đào Nguyễn Ánh - Hữu Hưng
Рет қаралды 19 МЛН
How To Fix a Frozen Traxxas Nitro Engine HobbyTown HobbyPlex
8:49
The HobbyPlex Show
Рет қаралды 25 М.
How to Start (and Stop) a Nitro RC car (RC Basics #9)
11:53
Razor RC
Рет қаралды 20 М.
Why Nitro Engines Outpower Everything Else
25:33
driving 4 answers
Рет қаралды 1,2 МЛН
Restoration of an old RC car engine - Impossible Restorations #1
23:23
ENYA 15-III Rescue Rebuild Model Airplane Engine
15:35
Michael Smutnick
Рет қаралды 50 М.
Nitro carburetor clean up
16:35
thebug 404
Рет қаралды 9 М.
Nitro engine stuck at TDC how to fix it easily
14:01
thebug 404
Рет қаралды 11 М.
Nitro Engines How To Clean a Nitro Carb
14:14
Haggard RC
Рет қаралды 3,4 М.
All about NITRO engines
35:42
RCModelReviews
Рет қаралды 68 М.
Шифранулся и попал на матч / Манчестер Юнайтед
0:59
Невиданный футбол
Рет қаралды 1,4 МЛН
The scary goat in 2012 🤯🔥🐐
0:19
mtsouzx
Рет қаралды 15 МЛН