How to fix dji mavic air 2 esc error | esc error fix | air2 air2s esc problem fix

In this video you will learn on how to fix ESC Status Error for DJI Aircraft.
if you not familiar with the component level repair please replace the esc board.
Don't forget to LIKE, SUBSCRIBE, & HIT the NOTIFICATION BELL for more update videos.
How to fix dji mavic air 2 esc error | esc error fix | air2 air2s esc problem fix

[@claudiocastillo2792]

hello what is the numerical reference of the mosfet. 7934? If so, this mosfet is compatible with various dji cards.

[@mrdrone1212]

My suggestion is to pick the mosfet from old people one. So there from factory. Nothing to worry when the drone is airborne.

[@stevrgrs]

Explaining what the heck you’re doing would be nice 😂

[@mosbinatuna]

yeah nah.....sending it in....probably lose all the screws if I tried this

[@mrdrone1212]

😀

[@vijayadarshmaageri8162]

Hi Sir your from my dorne crashed it works but some time shows aircraft processor chip overheating, and over moter sound. give me suggession. thank you.

[@mrdrone1212]

Which drone do you have…?

[@ramiaboshammalh8089]

Hey, how did you know the faulty mosfeth? In your examination of the motors, it gave the same reading in your video. Please help me. I have the same fault, and I have another faulty plate. I can take a mosfeth from it. Give me a way to find out the faulty mosfeth.

[@mrdrone1212]

first thing you have to take out the esc board. then you can check it with multimeter. try to check all mosfets with multimeter and check all component as well. i hope you can identify the the problem.

[@AzraelPercussionNEO]

Do you have a video showing that the solution of the replacement mosfit chip actually worked and actually show the drone flying?

[@mrdrone1212]

I promise. it actually worked well. But you have to get the mosfet from the old an original esc.

[@MrAboutLife]

What's the voltage output that should be normal when reading those levels

[@mrdrone1212]

Check in the video. It should not dead short

[@khaledfpv415]

How did you check the mosfet?

[@mrdrone1212]

With multimeter. Bro

[@jv-mv5ez]

Hell. I have a zino mini pro, from hubsan. Recently I crashed the drone but now it dont connect to the controller anymore. When I turn it on, it just beep once. The correct its to beep once, and then do a double beep. Do you know what could be the problem?

[@mrdrone1212]

I’ll let you know give me a sometime

[@az1373]

Hello, I hope all is well. I have Air2s and I am getting ESC error 30038. I don't see any mecanical issue so far and the drone has not been crashed. Can you give me some clues on what to check and how to troublesboot this error? Many thanks

[@mrdrone1212]

1st thing you have to check the motors. Check any coils are been damaged. If not. You have to change the esc board.

[@az1373]

Thanks for the suggestions. Motors are spinning with the initial check, just the back motors are giving red light and thus the error comes up. It is most likely the board as you said. Will try to order one and see how it goes

[@Lik3ish]

@@mrdrone1212 how about error 180043? what i do i didn't even crash it :(

[@shivamstudiosehi4007]

hallo sir how cost of esc board

[@mrdrone1212]

Check on AliExpress

[@charles-tw1hi]

Have one that is giving me esc over heating message, fan is working inside. need a new board?

[@mrdrone1212]

I was never faced this trouble. I guess you are talking about main board over heating issue. Check the thermal paste on the main board.

[@charles-tw1hi]

@@mrdrone1212 yeah its super weird. cant find anything on the web about esc's over heating. but i did remove paste applied new on the main board. i did notice some sketchy looking pinched wires so ill resolder them this evening and see if it improves. as far as flying it is fine until a battery swap with the message then motors wont spin up.

[@wilsonmultimediaanddronese3447]

Sir my marvic Air 2 controller went of and it's on till now what do I do sir?

[@mrdrone1212]

If you have warranty you can claim

[@mrdrone1212]

Or you have to replace the main board. There is no ic an other component to replace. They all manufactured by dji

[@arunadhithiya3357]

Cost of esc board

[@mrdrone1212]

Check out n AliExpress or eBay

[@thornysekyere7800]

Hello my DJI mini 2 remote control suddenly went off while flying, luckily the RTH landed the drone. Problem is nothing is working on the controller, not charging, no LED visible. Can you help please?

[@mrdrone1212]

Need to check the RC motherboard. Please contact me on email