How to Fix F51 Error Code on

[@kimlouleo]

Thank you! With this plus an additional video on how to get the stuck drum loose, we were able to pull out the drum, remove several socks, and put everything back together - no repair call, no replacement!

[@heatherpuca]

Kim, could you post link to video on how to get the stuck drum loose please?

[@paulragland6394]

This dude is right on. Washer came apart exactly like said. Found a sock under the drum. Thanks for the video!!!!

[@DIYRepairsNow]

Thanks for watching my video💯💯👍🏻👍🏻

[@landonkirby7309]

Thank you so much for this video!! I just saved $1,000 by spending 50 on a Stanley 40-piece socket set and a ratcheting screwdriver set. Your video walked me through the process. You made it so easy to fix. And I can hardly fix a sandwich!

[@DIYRepairsNow]

Thanks for your comment and thanks for watching my video👍🏻👍🏻💯💯

[@dawnkirk6028]

A million times thank you for this video! We had a bit of a fight to get the tub to come up, but finally got it. Found underwear and 82 cents in coins -which were in the drain tube just like the video. Saved us a lot of frustration, repairmen are hard to come by in our rural area.

[@swizard0922]

Dawn Kirk how were you able to remove the tub. Won’t seem to come out for me.

[@MichaelRei99]

Dawn Kirk you could have used a hanger to remove the clothing without removing the tub at all!

[@dawnkirk6028]

@@MichaelRei99 we would not have gotten the coins out without the tub removal.

[@mikedemaray1255]

This was the best DIY fix I've ever seen, and it worked exactly as shown. I would've never got this done without the video. Saved me lots of money and time. Thank you.

[@DIYRepairsNow]

Great to hear! I am Glad My Video Helped You! Thanks for Watching!

[@danwelliver7643]

Great video, very helpful. My Maytag Brovos had the green clips in the back so had to unscrew the upper fastener on each, then pull the top forward to unclip the front. My tub was stuck so borrowed the idea from another comment and cut a 2x4, 21" long with arcs at the ends to match the curve under the lip at the top of the tub. Used this, another block of wood on the center shaft, and a car bottle jack in between to pull the tub from the shaft. Found a few clothing items similar to the video. Gently filed a few burrs and rust spots on the shaft before reassemble. Machine works great now. Thanks so much for the video and all the great comments!

[@brianream9429]

Thanks for this video. F51 error was a result of 5 metal collar stays that were under the cover plate by the drains! No issues with removing the tub. Thanks for the detailed information!

[@JeffWiswell]

Great video! Just needed the first few steps but that corrected the problem by allowing me to get out the piece of clothing stuck in the drum

[@kgilsworld]

Thanks for sharing! We had an issue getting the tub out but we didn't want to pay the $130 for the tool in the link. After some different tactics my husband used a vice grip to hold the middle piece you put the tool on to keep it from spinning. My son held the wrench in place as my husband I lifted the tub and it came out with no problems! Thank you again for saving us money that we weren't ready to spend!

[@mommyknits]

Thank you soo much for this wonderfully detailed and clear video. We received the F51 error message while doing laundry last night and after following your instructions found the problem. Two socks wedged in between the tub and the basket. You saved us from calling in a serviceman. Thank you again!!!

[@Accurize2]

WOW! You nailed it. Found two wash cloths and 13 cents in the drain area. Now it’s running great and no F51 error. Thank you!!

[@wpbasics]

Thanks my friend. Turns out one piece of clothing was the problem. I didn't even have to take the tub out. I used a hook to fish it out.

[@lisavalaire]

I love this video I was able to fix rather than replace. Thank you thank you. Another idea is to make one showing reassembly. Would recommend this.

[@qixidojo4176]

Thank you. That was exactly my problem and because of your video I had my washer fixed in 2 hours without having to buy any parts or call anyone. Much appreciated : )

[@benjackson1350]

Thank you so much for this helpful video!! My blockage was not an actual item but my filter had to be cleared so I used a high powered spray bottle with half white distilled vinegar and water to clean it as well, once the filter was clear it worked again plus I was able to disinfect along the way.. Thank you for you kindness to post such a helpful video!! 🙏🏽

[@DIYRepairsNow]

You’re welcome thanks for watching my video

[@suzannev.799]

Big thanks to your video - all steps were correct for us, but almost all were very tough to complete. We didn't have a putty knife so used our Savor credit cards which are incredibly thick to push the tabs - it took a LOT of force and then we really had to pry the top open but it worked. We sprayed KROIL on the bolt, left it overnight, then used our socket wrench and hit it with a hammer to get it to budge. We used the Savor CCs again to lift up the plastic agitator cover by placing them as "handles" on either side. And we had to use a Car jack with a 1x4 piece of scrap wood we cut to size in order to get the drum out. We placed the wood inside the lip of the drum, the jack underneath and turned it until it came loose. We heard several noises towards the end that indicated it was beginning to come out so be patient. Eventually you'll get it. Found a penny and a small amount of lint. Before we put it back together we used steel wool to clean and smooth any metal pieces that were tough to get off, then we used plastic-safe greaser. After we put it together again we lifted it up enough to check on the hex bolt underneath. It was already tight so we knew that wasn't contributing to the problem. We now can run the washer without error. THANK YOU!!!!

[@kennyrubin2509]

Thanks for the car jack idea, worked like a charm!

[@laurieloomis1470]

Thanks for the video. It was just what I needed to get my machine running again! Found underwear, a couple of socks, and a dishrag 😄. I love that you don't rush through the steps, so it's easy to just pause and do the work, then restart it when I'm ready to move on.

[@austinreish94]

Great DIY video on how to remove the tub on a Maytag Bravos washer. It very much helped me when my washer ate my neck chain and threw it below into the agitator and some pieces went into the slots and went underneath the tub section.

[@Traviecee]

THANK YOU THANK YOU THANK YOU THANK YOU! I had mine torn apart and pulled 6 pieces of clothing, 10 pieces of change and 5 bobby pins from the bottom. All finished within 30 minutes. Again, thank you!

[@wilburwilson8018]

Thanks! This saved us a service call!

[@DIYRepairsNow]

You’re Very Welcome! Thank You So Much for the Support!!

[@wagnermaciel5896]

One of the best instructions video I have seen on youtube. Thanks to you my machine is back in business! Thanks again!!!

[@mercedesprovancial8230]

Wagner Maciel was yours not spinning?

[@wagnermaciel5896]

Mercedes Provancial I got the F51 code and the machine would stop in the middle of a wash. Thanks to this video I was able to fix the problem.

[@mercedesprovancial8230]

Wagner Maciel mine is doing the exact same thing right now haven’t had the chance to fix it.

[@MiddleCross378]

It was a couple pair of severely mangled underwear and a sock clogging mine, thank you for the excellent video, helped a ton!!!

[@DIYRepairsNow]

You’re welcome thanks for watching my video Mas Mas Mas Mas Mas are you💯💯👍🏻👍🏻

[@davidreef3269]

You are the man! Found a few socks under the drum and the washer is working great!

[@bethsmith8705]

Thank you so much for this video. Problem solved and found the lunch bag that mysteriously went missing!

[@tommybrown6869]

Thank you for this helpful video the nut on the bottom of my washing machine was loose just like you talked about tightened it up everything works perfectly

[@diossslogan]

Millon Thanks! Great video, problem solved. Had little trouble removing the tub but I have my washer doing it thing! There was fabric clogging the drain. 🙏🙏🙏🙏

[@Ch0uiNe]

Thank you for the video! Just had that F51 error and was able to fix the problem within an hour with your help!

[@DIYRepairsNow]

Ch0uiNe You’re welcome thanks for watching my video don’t forget to subscribe 👍🏻👍🏻💯💯

[@shellymaybury9410]

Awesome video! Can’t thank you enough! I’ve never attempted to repair a washer before and your video was so easy to follow! This was exactly the problem with my machine! Thank you again

[@abbeysomethingnormal7830]

Shelly Maybury Did you have to order your tub hub. Lowe’s looked at me like a crazy person

[@rick8676]

Nice tool, someday I may purchase it, but today the hydraulic jack/board method will have to work, wish you had actually shown the position sensor as other internet searchs have mentioned connection issues. Have a great day, really appreciate the enunciation and directness of your instruction.

[@austinriediger6537]

Thank you so much, had a shirt stuck outside the drum, got it fixed thanks to your video!

[@DIYRepairsNow]

You’re welcome thanks for watching my video👍🏻👍🏻💯💯

[@DIYRepairsNow]

You’re welcome thanks for watching my video👍🏻👍🏻💯💯

[@Ben-uv4ku]

This is a great video. Simple, to the point, informative. Thank you.

[@devilsadvocate676767]

Awesome awesome video!! Took some "elbow grease" to get the tub out, but it worked!! Thank you!

[@williamkibby6121]

Very thorough explanation of what you need to do. Excellent video. Well done! I'm sure you saved me a ton of money.

[@jasonrosenberg639]

0

[@rossfricke2010]

great video! definitely needed the puller, the center shaft had a bunch of rust & corrosion on it our problem was underneath the washer, the allen bolt holding the stator was loose, and the large nut above the stator was also loose, problem solved, thank you

[@roberttruesdell6151]

Great videos. I removed the tub no clothes. Removed the plastic piece on the bottom nothing stuck in it. Found the bolt that holds the rotor on loose causing it to ride low. I removed rotor to inspect it. And found the nut that holds the shaft and seal in place off as well. Retightens that remounted the rotor and righted the bolt. Put it all back together and it’s working now.

[@RegretfullyMine]

Extremely helpful. I’ve got it all taken apart and sure enough we found a few stray socks and washcloths. About $7 in change too. I’ll reply to this comment once I’ve got it back together. High hopes considering everything has worked out so far.

[@DIYRepairsNow]

Glad My Video Was Helpful!

[@RegretfullyMine]

Unfortunately this didn’t solve it for me, but I think I found why. The motor at the bottom of the drum is nonfunctional. I’m pretty sure if I can find a replacement part, that will solve the issue. Or I could just replace the appliance at this point, I’m due for an upgrade anyway. All the same, thank you for making this. I never would have found out what the issue was without your guide.

[@zephyr325]

This worked like a CHARM! Great instructions, including the followup on the tough parts. Thank you!

[@LincolnChispas]

Your explanation was very clear, even for an amateur like myself. Thank you! Problem solved.

[@MichaelRei99]

LincolnChispas he should show the machine not pre disassembled because it very rarely is that easy.

[@lucidstates6787]

i had the exact thing happen to me today and my first thought was oh shit the sensor went bad but thanks to this video it was a much simpler fix than i was thinking it turned out to be my wife's jammies so thanks for the video man.

[@DIYRepairsNow]

You’re Welcome! I am Glad My Video Helped, Thanks for Watching!

[@jamesjames1716]

Great video!!!! Thanks for information and expertise.

[@greenbaywacky]

Wow followed step by step and sure enough under my tub was 2 socks and a pair of underwear. I seriously was looking at new washers today and decided first to search code 51 maytag. Your video just saved me $600 bucks!! Tub was hard to get off a lot of wiggling and wd40 but those other parts slid right off. For the stuck tub I had my kids hold up tub and I hammered with a wooden dowel straight down basically a broomstick handle. My work around LOL. Thanks so much!!

[@DIYRepairsNow]

You are Most Welcome! Thanks For Watching!

[@reyrene]

BEFORE YOU TRY THIS, you should know that error F51 usually means that you have to tighten the screw at the bottom of the washer. Simply push the washer forward, then tilt it against the wall (no need to tape anything), and simply use the right size allen wrench (hex key) to tighten the screw while you hold the bottom so that it actually tightens. That's it. There is no need to remove ANYTHING AT ALL (unless you really got a suck or some other item stuck where this video shows).

[@DIYRepairsNow]

Thanks for this comment I also have a video Joanne that you can look it up on my channel thanks for watching my video 💯💯👍🏻👍🏻

[@suzannev.799]

Saw this comment after we spent so much time trying to get the drum out - was looking for tips. And at first I was like, "OMG, we did this for nothing" I'm happy to report your comment allowed us to check to rule OUT that it was not the hex bolt. Now I know more though and really appreciate your comment (we finally got the drum out and found only a penny and small piece of lint but apparently that was enough to mess with our washer - all fixed now).

[@guestmtl]

You make my Day :) by saving me time. I was about to jump for a second time into the excellent video of DIY (thank you for the video) finally after reading your comment i found that the screw at the bottom was loosed:( . I fixed it by following your instructions. Thank you for the excellent comment.

[@Oldpaint0216]

But . . . what is "the screw at the bottom of the washer"?? Any photo or illustration would be worth a lot. What does this screw adjust or control?

[@Oldpaint0216]

Actually, I later discovered what this referred to, after I'd moved from pulling the tub out and eliminating that as the problem. The F51 code suggested a failed electronic part that required coming up from the bottom to remove the stator. Unfortunately, while that took care of the error code, the real problem was a failed bearing, the cost of repairs for which came to about the price of a new machine.

[@evo_x2504]

Awesome how to video! Followed your method step by step and everything went well. We just had to clean the sensor and it fixed the F51 error. Quick and easy and took less than 20 minutes from start to finish. Thank you so much for taking the time to post this video.

[@milkmayun]

This post was quite helpful, at least until I got to the part where I needed a $165 tool to remove the stuck drum. That was more than I wanted to spend for a one-time tool, and shipping was longer than the Mrs wanted to wait for a repair. Couldn't find it anywhere locally. Did eventually use a grabber tool to fish out 7 coins that were beneath the drum, and so far the code seems to be cleared. I expect I'll have to replace the bearing soon, or else get a new washing machine, but this bought us a few more weeks (months?) Thanks dude!

[@jemlyn67]

You can use the scissor jack from a car trunk to remove a stuck drum. That's what I did. A bottle jack works too. There are videos that show how.

[@levipenner]

@@jemlyn67 That's helpful thanks. I'll google it and see if I can find a video.

[@alastairdinning2891]

really helpful explanation of how to remove the tub. Thank you!

[@DIYRepairsNow]

+Alastair Dinning You're Welcome. Glad my video could help.

[@sherryturner8729]

Thank you for this video. My son took apart my husband and I cleaned all the parts and we put it back together. So far so good. It’s agitating and hasn’t given the F51 code! PTL!!! Thanks again!

[@ptrippah]

Hi Sherry, How did your son/husband take out the agitator? Mine won't budge. Any tips and tricks would be very welcomed!

[@CharlesNolanArt]

Well I would say you have covered everything! Thanks! I hope I can beat repair man this time!

[@citymouse40]

Thank you for this very thorough video!! I just got the 'F51" error, I've never seen this before. Heading to the laundry room to disassemble it now...I hope I don't need any special tools! Update: You're right, that one part doesn't budge! but I did find a sock under the other part that I removed, then the washer worked again, Great video!

[@CharlesNolanArt]

As crazy as it sounds, i shook the washer several times then reboot it couple of times and it worked!

[@davidscott5903]

Awesome video! Thanks for the great information! 👍

[@DIYRepairsNow]

You bet! Thanks for Watching!

[@jordanhayes5135]

Wow! Great video with perfect amount of detail for the one off stuck drums! Great video shooting too! Thanks man!

[@jordanhayes5135]

also, if anyone needs the tools, u can get them as loaner tools from your local AutoZone. U need a Bearing Splitter Tool and then a CTA Push Puller Tool and you are set.

[@slaughtercrx]

I could not get the tub to pull out, but once i watched this I remembered seeing something black between tub and housing. Sure enough, I was able to pull out a t-shirt! How in the world do things even get in there? Running a load now to see if it fixed it. Thank you so much for posting this video. I'm financially struggling right now and could not afford a repair bill.

[@bettyeflynn266]

We just bought a Mayag bravo washer and dryer on last Saturday. Monday my daughter washed and there is water remaining in the washer. Could someone please help us so we can wash

[@danzei4862]

Thanks for this video. I followed this exactly, except used car jack and 2x4 cut to 20.75 inches and a 4”by4” small price to sit on bolt to pry up tub. (Guy has video in comments) Cleaned EVERYTHING interior with bleach and 409. WD40 and PB buster on bolt to accept tub when putting back on. (Toughest part was getting tub back on) Put all back together. Still got F51 with sort of normal to heavy load. Saw online that bolt on bottom was key. It was 1/4 inch Allen wrench on very bottom of washer. It was loose and caused F51. Other than bad bearings (noisy), I got a lot more life out of 15 year old washer. Thanks for everything!!!!

[@amberwalker1735]

Is the bolt underneath (bottom side) the washer or underneath the tub?

[@nghiabui4646]

Great Video, excellent tool for every handyman as needed on repair jobs. Thanks

[@mikehalladay4451]

Tighten drum center bolt underneath the washer FIRST. Looks like a flat washer but has a hex head bolt in it. Lean the washer back so you can get an arm and a wrench under it. Finger tighten first as it is very loose. This keeps the drum in Sync with the positioning sensor. All done!

[@kparmstrong5758]

This is the best comment on the whole thread! You’re a lifesaver! Thank you 😅

[@CharlesNolanArt]

Are you saying tightening that screw may be all you have to do?

[@CharlesNolanArt]

After seeing this I inclined to just call repair man but if tightening that screw works I will give that a shot!

[@mikehalladay4451]

​@@CharlesNolanArtyep. Worked twice in 7 years for me.

[@billpatterson6581]

Thanks you for the video, only a couple of things to mention, screw sizes are NOT designated by the head size or tool used to remove it. When you go to buy screws they are sized by the dia. of the threads. Luckily I had the Bravos XL model and the holes in the bottom of my tube are a lot smaller not those big rectangles in your model. So I did not have to remove my tube luckily. I did check the are on the outside of the tube had no clothes. So I checked the center screw on the bottom of the agitator by just tilting the washer a little bit. I found center screw REALLY loose I tighten that and no more F 51 code. But thank you for your idea of a tool to make and use for tub removal I may have to make one of those in the future. But instead of a plumbing 1 1/2 through wall fitting you are using I will just use some 3/8 NYLON or bigger cause it is easier to drill. Are the screws 3/4 or are the nuts 3/4, thanks dude .

[@csm19862]

My dude just saved me $500 from buying a new washer. Awesome 👍

[@DIYRepairsNow]

I am glad to hear that thanks for watching my video💯💯👍🏻👍🏻

[@nicholasplacke9882]

Great video definitely nice and slow to make it easy to follow, digging the coke nail 😂😂😂

[@Hdwrguy]

Thank you for this video. It was not fast paced and easy to follow along. I was able to remove some coins and gunk. Hopefully this will resolve the F51 error.

[@glennthomas7712]

Thank you for the video. This saved me a service call.

[@UncleMikeinGeorgia]

Great video. Thank you for posting. Your excellent video made disassembly a breeze. I found a few things and haven't had code f51 again but still have the crazy loud noise during the spin cycle. I think that's probably a bad bearing so that's my next move.

[@brendacarriere1570]

This information was very helpful. It worked perfectly!!

[@jaimeruelas3372]

THE BEST EXPLAINED VIDEO ILUSTRATED AND EXPLAINED

[@lporter8240]

Thanks for posting! Mine came apart easily. Found 68 cents. No more clinkity clink!

[@DIYRepairsNow]

L Porter Thanks for the comment and for watching my video.

[@seraphtcme]

thanks so much for the detailed video and troubleshooting tips!

[@ValRN09]

Thank you so much for making this video! We fixed our problem

[@DIYRepairsNow]

Jewell Desir You’re welcome I’m glad my video can help💯💯👍🏻👍🏻

[@kennyrubin2509]

Thanks for this video extremely helpful! But i used piece of wood and a carjack to get the tub out.

[@desijensen3187]

Excellent video. We were able to follow the it and now its running again. Thanks

[@gerardoguzman5083]

I have had the same F51 come up twice. Through the guidance of my brother, he had me check the armature which is the plastic cover under the washer that covers the stator. The armature retainer comes loose due to vibration and backs out and pulls the armature away from its original position. I was advised to use threadlock on the retainer, but, chose not to the first time and the code recurred and found the same cause. I bought and used the threadlock this time and I hope that the issue does not recur.

[@tosc4648]

Hey bud I really appreciate this video is very clear very thorough I did exactly as you described I n the video & it worked like a charm agood job thank you

[@scottmcdougall1692]

Thank you for creating this video! It really helped me!

[@santiagoflores6529trinidad]

Gracias señor iam just started en this business good luck to you teacher

[@EpsilonZeroKarts]

Thanks. Fixed my washing machine.

[@dakotachapman7576]

This is a great tutorial. Thank you!

[@UD1121]

Thanks you've saved me a lot of money

[@jamieweigold5234]

Well done! Had a pair of shorts stuck between the outside of the drum and the side of the washer. Check that area before removing drum.

[@jamieweigold5234]

*tub not drum

[@DIYRepairsNow]

Jamie Weigold you’re welcome thanks for watching my video💯💯👍🏻👍🏻

[@Giabella1]

Well done video. Very helpful. Good job.

[@stevengilber1153]

Great tool design and usage

[@belle7624]

Thank you!!! Great instructional video!

[@DIYRepairsNow]

Belle You're welcome I'm glad I can help thanks for watching my video👍🏻👍🏻

[@42scarletbloo]

Ty for this video very informative...my only problem now is getting the drum to fit back in ...the drum won't go back in

[@EmmaDuddy]

Hey this is an awesome video! We just moved into this house and have had nothing but problems with the existing Maytag Bravos washer. It will have an error code F1 when it is filling and then going through the rinse cycle. I saw on a different video how to get into the diagnostics mode and saw that the error code in the system was an F51. I'm hoping that I don't need to take everything out but, from your video, it looks like it is certainly doable. Who iknows what kind of crap the previosu owners have in their washer lol. Thanks for this!

[@topsocialpreneur2238]

This was a HUGE help... thank you so much!

[@jeannefallon-carine5802]

Thank you, excellent video....worked perfectly!,,,

[@Bulld0ggg]

This was a life saver, thanks for the video

[@Tone202]

great vid I need that tool.

[@certifiedyaminspector-dadd6224]

I have an issue. I was able to remove the hub fairly easily but the drum wont budge! I'm at a standstill & I have no idea what could be keeping the drum from coming up. It's like I didn't even unscrew anything... Got any ideas?

[@cindyhendricks4370]

I held the tub with both hands and upward pressure. Then, I had my wife tap the shaft, pretty hard, with the handle end of a wooden hammer handle. It took about a minute, but worked for us. Hope this works for you. Todd

[@dc5723]

Thank you very much for the video and tips. Our issue is not the F51 code but the bearings that sounds like an airplane engine on the spin cycle. Similar procedure though, thanks.

[@DIYRepairsNow]

You're welcome thanks for the watch my videos

[@PNFLnetwork]

Great video but I am stuck and cannot get out that 2nd part of the tub hub and do not have all those tools to get it up......not sure what to do now. Not going to spend $130 for tools I will use once and no certain outcome. But I was impressed with the detail of the video.

[@PNFLnetwork]

I finally got that piece out but now the tub itself is stuck, not moving at all....earlier it was at least going and up and down an inch....now its just stuck in place :( One lousy step away!

[@andriilebedynskyi3562]

Thanks for you video!! Really helpful!

[@phonseking9759]

Thanks, all fixed. Great video.

[@scotsnyder6486]

One of the best videos for F51 Error Code. Q: Where can I find this tool?

[@DIYRepairsNow]

Scot Snyder The link It’s on the description of this video

[@mastermolar]

Thank you! Great video!

[@freddym7425]

Great job on the video

[@trishwishnefsky8483]

Thank you!!!! I found 6 pieces of clothing tucked away in there. How does this happen? Lol, so happy right now!

[@kylewagner6607]

Overloading

[@MichaelRei99]

Trish Kodack customer abuse!

[@scottburditt4983]

Excellent video tutorial.

[@DIYRepairsNow]

+Scott Burditt thank you

[@nicholasdalessandro2374]

Thank you easy fix!

[@paramjitjuttla8728]

Thanks for the video. It is awesome!!

[@92blaspe]

I get as far as lifting the drum and it still resists. I find myself needing to hold the unit down as I left, which is hard. Idk if it’s rust or something jamming. I can wiggle the drum but that’s about it. What would help get a stubborn drum out?

[@thesliprocks1]

Just a heads up, I did your repair video for replacing the bearings (great vid) and a few weeks later got this same error. Turned out the bolt that uses the allen head came loose because I didn't tighten it enough. I tightened it and the sensor error went away.

[@CyclonetoMars]

This did the trick. Mine was loose too. Thanks

[@peterbennett7983]

Exactly the same problem and solution with me!

[@ZPrezton]

Nice video , I was searching for a video due to my same washer always stopping at last 11 min due to UL . I readjust cloths it spins fine up to 6 min and stops UL and goes back to 11 min. This goes on forever. Cloths are spun dry but this cycle never completes . Thinking of pulling the tub as you did to see if anything is under The drum. Would a socks or something be causing this problem? Thanks Orlando FLorida