HOW TO FIX FAN NG ERROR - SAMSUNG MX HS9000 MX HS8000 MX FS9000

My tests have shown that "Fan NG" is rarely due to a defective fan! Rather, its cheap connector is responsible for this, as it loses contact with the pin on the motherboard over time and due to temperature fluctuations. This is especially noticeable with the blue cable, which transmits the signal of the fan control (or not, then see Fan NG). Here you can unplug the connector from the motherboard, clip the metal pins out of the connector with a fine slotted screwdriver and use a small pair of pliers to bend the very cheap metal back together a bit tighter so that it ultimately closes tighter around the pins of the motherboard again. Very simple solution to an insanely common problem.... Optionally, you could of course solder a standard fan connector on the motherboard and replace the fan accordingly, then should be even longer peace.

[@marksamuels1273]

Fix my fan NG as per video works 100 percent Thanks so much saved me couple of Rands I'm from SA

[@andresolvera1546]

Yes I just did it and it works thanks for share this helpful information

[@lucasmatos9606]

Hello Friend ! his technique was accurate, I just did it and it worked very well, I'm from Brazil, thank you very much for your knowledge, it helped me a lot !!

[@Deepztech]

You're welcome friend..

[@claudemirchagas7458]

Boa tarde Lucas tudo bem amigo tenho um som fxs 8000 dar certo esse champe. Tem como vc mandar a foto do champe no teu som.

[@Deepztech]

@@claudemirchagas7458 ? english pls

[@jucineimorais3736]

Estou com aviso de protect quando aumenta volume e desliga... pode me ajudar? Grato...

[@marciliofroes2556]

O meu MX fs8000 está mostrando Protec quando aumento o volume até 24 ele desliga

[@vicentepinungan7041]

I wanna try this, thanks a lot.

[@lorenzobyers7361]

Mx hs 9000 goes into protect mode any suggestions?

[@lukeavio2002]

What gauge wire did you use?

[@Deepztech]

Its a normal wire. You can use any kind of wire

[@sirvirgenprince8571]

@@Deepztech and how did you know the resistance of the wire to be 100 ohms?

[@Deepztech]

@@sirvirgenprince8571 no need to measure the ohm, just use a normal wire

[@vanessatelles8183]

Eu estou com um som com esse mesmo problema oque poder ser?

[@Deepztech]

check the path

[@lalasantos8899]

Oi. Eu tenho um desse. O meu. Ta se desligando sozinho q eu lg. I q pode ser. Vc pode mi ajuda

[@Deepztech]

envie-me um videoclipe do seu problema ( se você pode usar inglês)

[@ferrantegabelli4817]

From the video i didn t see well the right point. Thanks very much

[@Deepztech]

Pin no. 76

[@ferrantegabelli4817]

Lions Kingdom Lions Kingdom i tried but i don t find, my model is mx fs8000 , not mx hs 8000 but seems exactely the same. I search this pin 76 for a lot of time but i don t find, i tried to zoom on your video but nothing. I found the zone where is but i can t understand which is the exactely point

[@Deepztech]

Send me an image

[@engineernelson3732]

@@Deepztech please I have fs8000 and it'd same issue

[@Deepztech]

@@engineernelson3732 chack the path

[@charmandales9578]

Hello can someone help me with my problem? My Samsung MX-FS9000 Giga Sound System doesn’t work. It says hello but eventually turns off.

[@Deepztech]

try to turn on without your speakers

[@thacianimaria2764]

O display do sansung fs8ooo não mostra os nome apago mas a luz está acesa

[@jjtovaldo]

En contraste el problema de tu samsumg gigga Yo tengo el mismo problema

[@stephenparker2510]

Will this work for Samsung giga 4000 watt hi fi system ? I’m getting no sound to speakers on anything like the radio, Bluetooth aux or CD player

[@Deepztech]

Whats the model number

[@stephenparker2510]

Or do you know how to fix my issue Is there a resistor I need to replace ? It doesn’t play any sound at all

[@stephenparker2510]

Mx-jjs9500

[@stephenparker2510]

MX-JS9500 I’m not having any fan issues or codes Only sound won’t play for any function

[@stephenparker2510]

There are a lot of people with my problem for this model But no one has given a solution Anywhere

[@DARTANYAWILLIAMS]

HOW TO FIX FAN NG ERROR mx-js9500 giga sound system

[@cocodosossegoitapissuma-pe9925]

Mano onde compro esse fio amarelo.?

[@Deepztech]

contact me on facebook

[@MrZemp99]

Do you know how to reset the Bluetooth it just stays on wait and don’t go to ready

[@Deepztech]

During “No Disc” Displayed, push the stop Button 5 seconds. After displayed ‘INITIALIZE’ set will power off automatically

[@antoniavaquera644]

Can i you show how you exposed the motherboard?

[@Deepztech]

i cant get you

[@marleneruhnt8457]

Estou com ploplema com esse som alguém poderia me ajudar

[@techerzgamingboyz884]

Hi will this work on HTF6500

[@Deepztech]

can u send me a picture of mainboard ? whatsapp [phone]

[@joelhernandez4106]

Can you help my mx-ms8500 won't stay on

[@Deepztech]

any error messages on the display?

[@tranhoang91]

How about for HT-J5500W?

[@fAiz_bucek]

so im try but not work

[@Deepztech]

Check the fan

[@carloscomde5388]

mano min de uma dica meu Samsung jiga sonud de 2600 vatis estar só xiando. é na tela dele aparece booting sound .isso aconteceu depois q eu coloquei á antena do rádio. é já tentei de tudo. reiniciei como você fez no vídeo mais nada adiantou

[@Deepztech]

aparece algum erro no visor?

[@bricesteetle3936]

What does it mean if it says protection then shuts off

[@docgonzo1973]

If it says protect could be the AMP, POWER SUPPLY, OVER HEATING. With the unit unplugged and fully discharged. Measure the resistance between the negative and positive of each speaker output jack. It should read around 2.2K ohms. If it's way off then the problem is in the amp section.

[@telmamoraes4932]

Quanto é pra vc arrumar?

[@Deepztech]

Eu sou do Sri Lanka

[@javiermontilla8786]

Hello, good afternoon. I have a mx-hs8500. I do that procedure and it does not solve. Well the problem with my computer is that it turns on and then says protect bye and turns off

[@lorenzobyers7361]

Was this issue ever resolved cause mine does that exact thing

[@Deepztech]

What is the error code?

[@lorenzobyers7361]

@@Deepztechprotect

[@Deepztech]

Check amplifier side voltage is present or not

[@lorenzobyers7361]

@@Deepztechwhat do I need to look for

[@telmamoraes4932]

O meu Som tbm ta assim , como faço pra arrumar

[@Deepztech]

explique mais

[@telmamoraes4932]

Tem como vc arrumar o meu

[@Deepztech]

certo. Posso te ajudar

[@ricardomancera5968]

I have a MX-HS8500 and it doesn’t turn on , it worked perfectly fine but then would turn on and then turn off by itself right away and now it doesn’t turn on at all.

[@Deepztech]

is it displays any error messages ?

[@ricardomancera5968]

Lions Kingdom it wouldn’t display any errors, it just turned off and it no longer turns on . It’s been off for I could say 2 years probably .

[@Deepztech]

@@ricardomancera5968 Check your power supply output voltages all of fist.

[@luzamandasanchez1134]

I have the same error in my model mx-fs9000 can you please help me with details

[@Deepztech]

sure. contact me on WhatsApp [phone]

[@jerrymrivera]

Mx fs9000 looking for the resistor pin but not sure. Can you help out?

[@jerrymrivera]

@@Deepztech can you help me out with mx-fs9000

[@gracekgracek8132]

What is real power? 137w?

[@Deepztech]

What do you mean by power? Power consumption or amplifier output wattage?

[@03-de-hu-alexanderwilliaml85]

NO SIRVE ESTE EQUIPO NO ME DURO 4 MESES

[@Deepztech]

i can't understand your language