Following this video, I was able to successfully change the battery on the iPod 6th gen. I especially liked the idea of using a template to store parts. Beautifully shot, good sound.
@outsourcerepairs3 жыл бұрын
Thank you for the feedback and I am glad you were able to replace the battery in your device successfully.
@joeloreilly33996 жыл бұрын
Thank you very much for this very well done video! I had purchased a new battery from you and was very nervous about installing it but your video walked me through it and my iPod seems to be doing good :)
@outsourcerepairs7 жыл бұрын
To order a replacement battery follow the link below: www.outsourcerepairs.com/collections/oem-parts/products/apple-ipod-touch-6th-gen-battery To order solder supplies follow link below: www.outsourcerepairs.com/collections/soldering-supplies
@outsourcerepairs7 жыл бұрын
Hello, If you have a multimeter test the battery voltage on the battery. If it is between 2.8-3.0V the battery may be bad. What symptoms of battery failure did you have before replacing the battery?
@outsourcerepairs7 жыл бұрын
Which pad did you remove? Right, center or left pad? This is what is causing your boot loop.
@outsourcerepairs7 жыл бұрын
Okay, the board may be able to repaired or not. You can contact a local cell phone repair shop and see if they can perform the repair, if not you can mail it in to us and we can run a jumper to connect the battery to the missing solder pad circuit. If you have any further questions please contact me.
@ytr4827 жыл бұрын
Out Source Repairs how do you know if it's the battery
@ianhobson14 жыл бұрын
Thanks for the great video. Simply the most helpful video for this issue on the internet. Thanks from Ian in the UK.
@outsourcerepairs3 жыл бұрын
Glad it was helpful!
@outsourcerepairs7 жыл бұрын
To order mail in repair service follow the link below: www.outsourcerepairs.com/collections/apple-ipad-ipod-iphone-repairs/products/apple-ipod-touch-6th-gen-battery-replacement-service
@outsourcerepairs7 жыл бұрын
Hello, Can you provide me a picture of your solder job/the battery connection on the logic board? You can upload the photo via the ink below and then send the link to me. postimage.io/
@1502shado7 жыл бұрын
mark cashman j
@ninajackson38977 жыл бұрын
I'm really in need of getting my son's ipod 6 screen replaced, what do you charge? Or can I send in his locked ipod 5 with a perfect screen to replace it?
@ojiwankenobi5 жыл бұрын
Thanks for this. I just now used your instructions to replace my iPod 6 battery. It’s reassembled and charging at this moment. (Knock on wood). My battery connection cover seemed to have been glued to the connectors at the factory. No desoldering was necessary. Before soldering the new battery onto them, I smeared a bit of solder to each of the iPod’s battery connection points. Other than that small difference, my experience was similar to that depicted in the video.
@tbamagic3 жыл бұрын
well- this just convinced me to have it done professionally
@Mike-ic1um3 жыл бұрын
yep, me too
@usneod9329 Жыл бұрын
Ditto!
@jonathanwhitaker60984 жыл бұрын
Dear Outsource Repairs, Thank you for this excellent video. While my attempt to repair did not work out (the unit did not turn on after I put it back together), I would like to e-mail you the unit with a new replacement screen, new replacement battery, and new back cover so you can use for spare parts. I hope this can save you a few dollars and serve as a Thank you.
@Magsimoo4 жыл бұрын
Battery check: sometimes new ones are faulty. Never put item bk together until tested and working. It will come back out really easy next time now
@isthtmg7 жыл бұрын
Seems easy but the soldering part, I don't understand. Can I just unsolder the battery connections and then re solder then and it the iPod will work just fine?
@BillAnt5 жыл бұрын
You need to remove the excess solder first with the desoldering braid to lift away the connector cleanly without damage. Honestly this repair is not for beginners/novices due to its difficulty level, you're better off taking it to a local mobile repair shop and they'll do it for you properly for a few bucks.
@drochalsey6 жыл бұрын
Thank you SO much! Absolutely excellent video. One quick question though … does anything need to be reset, as I saw some sort of "repair-screen-display??" when you were connecting and disconnecting the battery to AC, or does that just go away after the 1st* springboard boot up? {*1st after battery replacement, that is}
@BrianWMay3 жыл бұрын
I find IPA is good for removing adhesive, using a syringe and allow it to run behind the battery. It won't damage the plastic or electrics at all. Just give it time to evaporate before powering up.
@Dan57Thom4 жыл бұрын
Very comprehensive. Worth the watch!! Thx
@outsourcerepairs3 жыл бұрын
Glad you enjoyed it!
@modelman60595 жыл бұрын
Your very fine video has given me the confidence to go ahead and replace the battery in my ipod touch 5th gen. Thank you for your expertice. I am aware that the home button will need to be removed on the 5th generation model as it fits through a slot in the metal shield.
@EvilGhost4206 жыл бұрын
Hey, would you mind telling us what kind of tape u used around the connection, and what flux did u use around 14:14 on the video. Thanks.
@BillAnt5 жыл бұрын
It's called Kapton tape which can withstand high temperates without melting, while the flux is just regular soldering flux which it's not really critical in this case.
@SumanDevi-jl7np4 жыл бұрын
Apple iPod Nano 6th Gen. Battery Available Rs.380/= 6months Warranty. Whatsapp. No.9811-963434
@beejaethirtyone7952 жыл бұрын
I have a previously opened 32GB unit that has a boot loop issue. Would you advise me to take the memory chip from this particular unit and place it in a ipod 6th gen that has a current chip of 16GB? My thanks for your help
@Artemicion3 жыл бұрын
just replaced my battery with this guide. thank you so much.
@outsourcerepairs3 жыл бұрын
You're very welcome and I am glad you had a successful repair.
@soggybrownpanda33753 жыл бұрын
replacing batter on my ipod for the second time. Always come back to this vid to ensure i don't botch the order on the solder points.
@outsourcerepairs2 жыл бұрын
Thank you for the feedback.
@puluqemil2 жыл бұрын
great video, thank you so much! i am going to change the battery of my ipod
@outsourcerepairs2 жыл бұрын
Glad it helped
@gearcased24396 жыл бұрын
What temperature is your iron at when soldering?
@elvispressedtalot98995 жыл бұрын
when the soldering melts the way it does. . it has to be up in the 280-320 'F
@BillAnt5 жыл бұрын
I usually set it between 150 to 180 C in case your station's dial in in Celsius ;)
@apu_apustaja4 ай бұрын
Very helpful. I hope you've bought some better lightning cables since then. :P
@outsourcerepairs4 ай бұрын
Smart move purchasing a better cable and I am glad the video was helpful. Thank you for the feedback.
@steveh1306 жыл бұрын
Thx for the vid, have 1 question. During the moving around the tiny square piece I guess is the camera on the cable detached from the lense. At 29:38 in the vid u can see it at the top center near the numbering printed o the top cover, its a mesh like tiny square assy. The lense may have a little junk on it too. what to clean it with and use tiny dab of glue to reattach?
@brianschneidewind57564 жыл бұрын
Bought a battery from you and followed the directions (old battery worked ok, just wouldn’t hold a charge for more than 20 min), but I’m getting the low battery icon with a red stripe after charging for a while. Any advice?
@brianschneidewind57564 жыл бұрын
My bad... I must not have lined up the terminals well the first time. Resoldered, and it works fine now!
@michaelp30765 жыл бұрын
you don't need to heat the back to get the battery out. the 3M adhesive taps are accessible if you have a fine nose needle nose pliers or good tweezers. the black pull tabs are located one on the bottom right side of the battery and the other is on the left side at the top just under the battery cable. they are stretchy enough that once you grab a hold of the tab you can carefully pull it and the adhesive strip will come out.
@Magsimoo4 жыл бұрын
Apologies for the stupid question. May I ask about the soldering? Is it actually needed or can you change the battery without it. Thank you
@outsourcerepairs4 жыл бұрын
It's not a stupid question. Unfortunately you'll need to solder the battery to the logic board.
@rhen12152 жыл бұрын
So I peeled off that sticker thing at 7:27 but the metal sheet came with it. Now it won’t turn on. Is that the problem? If so where can I get a part for it
@outsourcerepairs2 жыл бұрын
Hello, The tape serves as a barrier between the EMI shield and battery connections. You can replace it with a thin piece of electrical tape or kapton tape. As far as the iPod not turning on I'd need to know a little more about the state of the device. Is the device fully assembled and does the Apple logo come on then shut off?
@rhen12152 жыл бұрын
@@outsourcerepairs just no power at all. I burnt off the third pad on the battery contact but got it resoldered and in there good. Even with a super fast lighting cable that can even power on things without a battery there just seems to be no sign of life at all
@rhen12152 жыл бұрын
@@outsourcerepairs no no also like the metal part of the tape came off in pieces as well you peeled off the black tape well with mine it peeled off that metal part with the black tape. Could that cause a problem?
@larryfarrell30945 жыл бұрын
Thank you so much. It is always good to "see" what to expect. Do you have a video for replacing the charging port on this unit as well?
@kamalakelly62085 жыл бұрын
Why the hell on earth Apple didn’t make it easy and simple as iPhone battery?
@falcon36614 жыл бұрын
Why didn’t they make it like the old Samsung phones with a removable lid? Honestly Apple is trash
@americanteehee56994 жыл бұрын
@@falcon3661 I guess that capitalism is the answer you are looking for 😅
@chicosuavae67644 жыл бұрын
american teehee Okay, Zoomer. No, that’s not the reason.
@willia3r4 жыл бұрын
@@chicosuavae6764 actually, that is the reason. More specifically, _"planned obselence."_
@nickhowatson47454 жыл бұрын
they went for a specific style where users would have the easiest and most simple user experience. they didnt want to have a removable back because people are idiots and they will break shit. they basically are trying to make the phone so easy and simple to use that a baby can do it. you cant break the phone by using it.
@shadowfoam34915 жыл бұрын
What's the brand of the hot air desoldering tool you're using? Is it one you'd recommend for others? I'm readying to make this exact same kind of repair.
@joseantoniogarciastivalet41535 жыл бұрын
I change the battery of my iPod and it does not charge completely it just reach 53% and thats it, when I disconnect it from the power it almost immediately goes to almost 5%, I really don't understand this, Do you have any advise to this matter? Thanks.
@BillAnt5 жыл бұрын
Most likely the middle pin of the battery called the BLI/BSI (Battery Level Indicator) is not soldered on properly, therefore the phone won't charge accordingly. Try to reflow the solder again on the middle pin with more flux. It's also possible that your "aftermarket" battery is such low quality that the phone simply rejects to charge it. Don't forget, "You get what you pay for!" ;)
@Duckers_McQuack5 жыл бұрын
Did you make that smaller pipe on the tip of the heatgun to concentrate the heat in one spot? Or where did you buy it? I´m gonna start doing this stuff myself as well. Also, got the template i can print too for that ipod sheet to put the screws on?
@831Adventures6 жыл бұрын
what type soldering gund and heating gun you used
@Hellfire_The_Doberman2 жыл бұрын
This is very helpful but where do you get the sheet shown in the video
@outsourcerepairs2 жыл бұрын
What sheet? Please advise so I may assist you.
@Pss-pss-pss5 жыл бұрын
I don't have the heat gun, what are the other alternate options to begin the first step of getting that gap finally to slowly pull the front screen.. My ipod boots in loop and I am assuming it could be the battery issue
@crunchb3rry5 жыл бұрын
I follow most of this, but am confused about the solder type. Was that lead solder from somebody else? A factory iPod have lead-free rosin core solder, right? So for a stock (ie: never cracked opened) iPod, just use the rosin-core for this procedure?
@kandyfix9221 Жыл бұрын
Helped . Thanks
@outsourcerepairs4 ай бұрын
You're very welcome. Thank you for the feedback.
@dragonwarriorlegend88387 жыл бұрын
Great video!!! I Just replaced my i pod 6 gen. Battery and everything went great. but now the battery will not charge over 28%. when i go into setting under battery i get no info. check voltage on battery and its good. dont know why it will not charge. when you plug in the charger its says charging. please any thing will help
@outsourcerepairs7 жыл бұрын
Do you have a multi meter? If so test the battery(Disconnect battery from logic board when testing) and let me know how many volts the battery has?
@dragonwarriorlegend88387 жыл бұрын
This is a iPod touch 6 so i will have to desolder the battery. I am Getting 3.81volts on the far right and center with no charger and battery at 20%. and 4.12volts on the center and 3.81v on right with the charger hooked up. I can Desolder the battery if needed.Just want to make sure before i do that. Thanks for all your help.
@dragonwarriorlegend88387 жыл бұрын
Out Source i Desolder the new battery and checked voltage it was 3.78v. Solder the battery back in and now it's working. Charge up to 100% . I have one more issue maybe you can help with. I broke the front facing camera and order a new one. How do you attach the contact point to the logic board?
@outsourcerepairs7 жыл бұрын
Before installing the front facing camera make sure you disconnect the battery. When installing the new front facing camera line up the solder pads on the logic board with the solder connections on the front facing camera flex cable then tape in place. Do not cover all connections with tape because you are going to solder the cable to the logic board. You're only using the tape to hold the cable in place while soldering. Once you are finished soldering the front facing camera flex cable cover solder connections with Kapton Tape.
@dingusbingus85545 жыл бұрын
With new batteries you need to charge it to 100% before doing anything so the battery remembers to charge to that level
@JPMitreN3 жыл бұрын
Question, and this might be a dumb one, but is a true honest question: would the iPod still work with out the battery? I just took mine out (maybe the wrong way, I still did it)
@outsourcerepairs3 жыл бұрын
No the iPod would not function without the battery
@JPMitreN3 жыл бұрын
@@outsourcerepairs yeah I found out
@chernandez3035 жыл бұрын
I followed this video step by step and was able to get a good solid connection after soldering the new battery connector. When I turned it on, everything was fine. As I put the battery flex cable cover on with no Kapton tape, I got a spark and it burned a small hole in that cover. Would that be caused because there is no Kapton tape between the solder and the cover or would it be caused by something else??? Please help, thank you.
@NBMSCH2 жыл бұрын
yesterday i found my ipod 6th gen screen popped up (likely wasn't shaterrend) i knew it was the battery (swollen) but now the plastic frame/bezel that holds on the LCD is loose... i don't know what will happen after installing a new battery because this frame that has the clips that holds on the metal housing.. will the LCD remain loose or should i glue it? thank you
@outsourcerepairs2 жыл бұрын
The adhesive on the EMI shield will hold the digitizer in place. If you decide to glue the the frame to the LCD make sure you use an applicator and apply very little glue so it does not seep out onto the screen. Any further questions please let me know.
@michelleford37484 жыл бұрын
The solder that is used in this repair, is it a rosin core flux solder?
@marytyler16445 жыл бұрын
Were can we get this done in Beaumont Texas?
@anneanne71055 жыл бұрын
Awww thought all was going well until you did the soldering hmmmmmm. This newer ipod is not half as good as the old ones they just keep going forever. This one has been replaced once under warranty and now the battery is kaput, I guess. Your demonstration is superb but still too hard for me unfortunately.
@SonnetGomes3 жыл бұрын
If the battery OEM? I would be surprised if Apple allowed any of their OEM parts to be sourced, but I would very glad if they do. My ipod could definitely use a new battery. Rather than throwing it away, it is a good way to recycle and keep the environment clean.
@zzdorite224 жыл бұрын
There’s a small piece on top of the board that might be missing where you connect of lay the flap down. Would this make the battery not come on??
@elvispressedtalot98995 жыл бұрын
Got 1 Question . thats bugging me .. and if i should try it... But The Question goes like this.. Would my Heat Gun , capable of going 1500'F be good to heat up those 3 pins that connect the battery? and would anything else get burnt .from the heat usage? or if anything on the ipod will survive?
@ochetus4 жыл бұрын
what temperature use you to desoldering glue of the cover?
@outsourcerepairs3 жыл бұрын
170 C and 70 air pressure.
@alf7175 жыл бұрын
Very helpful video. Thank you.
@elvispressedtalot98995 жыл бұрын
Usually .. theres too much Pocket DIRT in those little charging Ports!!
@rgray3182 жыл бұрын
Do you provide the battery replacement service for 6th generation ipod touch?
@outsourcerepairs2 жыл бұрын
Hello, Yes I provide the service for the Ipod Touch 6th gen. You can view the service via the link below: outsourcerepairs.com/collections/apple-ipad-ipod-iphone-repairs/products/apple-ipod-touch-6th-gen-battery-replacement-service
@emiliobuhr50617 жыл бұрын
I bought an ipod off off ebay won't charge nothing I'm kind of short on money would you do the repair for $25-30?
@BillAnt5 жыл бұрын
You can always try a local mobile phone shop, some crack heads do it for as low as $10 bucks. lol
@larryg71095 жыл бұрын
Where do we get the heater thing? Can I use a hair dryer?
@elvispressedtalot98995 жыл бұрын
Can you .. Type in Some Makes and Model for Each item you use. Specifically ; soldering and flux paste . from Good to bad.. Amature trying out a repair job. virgin skill level
@Esanes144 жыл бұрын
Do you accept mail in repair orders from outside the Continental U.S. ? I reside in the US Virgin Islands.
@LiamJones-bm1eu3 жыл бұрын
My iPod touch 6g screen is lifting up really bad the home button is coming out of place and WHOLE lcd shining through
@TheNotoriousJLB6 жыл бұрын
I have a iPod Touch 6 and it overheats every time I sit it on something can u help with it before my fingers burn off?
@MegaLegends1236 жыл бұрын
with apple admitting what they did to the batteries, after iOS11, would the replacement batteries being sold be available for these iPod Touches or no?
@outsourcerepairs6 жыл бұрын
Yes they should be but you will need to contact Apple to confirm.
@stevedawson122 жыл бұрын
Great Video
@3dwrld34 жыл бұрын
Great video. I got the ipod working but then shortly after I believe I bridged the connection. Now it will not turn on. What can I do from here? Thanks for the help.
@flawlessfatality81056 жыл бұрын
My ipod touch 6th gen won't get past the dead battery logo when i plug it in, I never had battery issues her or this started happening. I hadnt used it for a couple month and then this started to happen, so I need a new battery? I've tries the reset methods with holding both buttons down and it hasnt worked
@Mik0I5 жыл бұрын
Any progress?
@crxmassive5 жыл бұрын
+Out Source Repairs is your website still working? Those links are not working.
@aaliea075 жыл бұрын
Hi , I just bought an iPod 6 from someone and the battery dies fast , how much is it for you too fix ?
@MAINGUYEN-fi6lj4 жыл бұрын
what type of tape you use to tape down the battery???
@drahunter2135 жыл бұрын
Can a longer lasting battery be installed in the iPod touch 6? Is their even a battery that lasts longer then the original battery? Anyone know of such a thing?
@kernel_data_inpage_error4 жыл бұрын
I replaced mine, it works but the battery drains itself (even when turned off completely!) What can be wrong? Also the iPod gets hotter when I use it, I don't see any major problems, loose or shorted connection?
@outsourcerepairs3 жыл бұрын
Sounds like you may have a short somewhere on the board. Ipod 6th gen notoriously drain or display an incorrect battery percentage.
@robertb33615 жыл бұрын
Excellent work here, I learnt what I needed!
@chipwatson5901 Жыл бұрын
I have replaced batteries on 3 different ipods that I own. Every time, the new battery gives me fluctuating charge readings and seems to drain rapidly even when the ipod is not used or is turned off. The fully charged battery will be dead in 24 hours. The 3 batteries I bought were from different battery manufactuers and different sellers. Am I that unlucky that all the batteries were bad?
@outsourcerepairs4 ай бұрын
No you're not unlucky but more than likely the charging IC chip in your iPod is defective.
@garydavies33283 жыл бұрын
How do i test the battery first, to make sure it is that which is faulty?
@outsourcerepairs3 жыл бұрын
You can test the battery with a multimeter. What's the symptom your device is having that makes you suspect the battery is defective?
@ThePestoner3 жыл бұрын
do i need the flux? can i use something else instead?
@outsourcerepairs2 жыл бұрын
Yes you'll need flux.
@pxndxlunx58217 жыл бұрын
Hey, I have an ipod touch 5, I've bought the battery and wondering if I can send it to you guys so you can install it, I can do $30, wondering if that will work, if not, thank you very much for answering my question :)
@progressinthemaking67327 жыл бұрын
Have you ever ran into a problem when removing the battery and prepping the pads for the new one, there seems to be nothing there? Like the pads are missing? I'm working on a ipod nano 7 and have ran into this issue. Never seen or experienced this before, could send pictures if you need to see what I mean! Thank you!
@outsourcerepairs7 жыл бұрын
Yes please send pictures, it sounds like the solder pads may be lifted from the logic board. Upload the photos to the website below, you do not need to sign up and then provide me with the link. postimages.org/
@BillAnt5 жыл бұрын
If the pads have melted and lifted away due to the soldering tip temperature being too high, you could probably trace it on the circuit board and patch the battery pins with extension wires. It's not for the faint-hearted to do. ;)
@rosshay54716 жыл бұрын
I had a gen 6 ipod touch put in for a repair as this is a repair I didnt have the knowledge to fix. Was given back to me as unable to repair. On inspection the middle soldering pad has been pulled off. Is this pad to so with charging? The device powers up but doesn't charge. Is there a way to repair the soldering pad I've read applying an epoxy then solder to this is this possible? I cant find a guide on how to repair the soldering pad
@suzesraccoonjs64656 жыл бұрын
This seems like a tough question go to there website in the description :)
@suzesraccoonjs64656 жыл бұрын
And contact them
@slakakakakkaaka5 жыл бұрын
Where can I get the under metal shield
@Chrisadeth7 жыл бұрын
Hello. Quick question. For mail-In services is it international?
@outsourcerepairs7 жыл бұрын
Yes
@ninajackson38977 жыл бұрын
My son has no experience with this and I definitely don't lol, but what if I were willing to pay and ship my son's ipod 6 to you? Are you willing to fix? He just needs a screen replacement and he has a locked ipod 5 with a perfect screen can that work? If so I'm willing to pay 25 or 30$ and you can keep the 5 for spare parts or sell the parts. Please reply
@outsourcerepairs7 жыл бұрын
Hello, Yes I can accept that offer please contact me via the link below. I look forward to hearing from you. (Contact me via contact tab) www.outsourcerepairs.com/
@steo.c7 жыл бұрын
Are the 5th and 6th gen batteries the same? Like would a 5th gen battery work in a 6th gen?
@outsourcerepairs7 жыл бұрын
No the batteries are different . Ipod Touch 5th Gen Battery is 3.7V 1030mah and Ipod Touch 6th Gen battery is 3.83V 1043mah.
@ZachCanReact7 жыл бұрын
Out source, I have recently replaced my screen on my Ipod touch and now it wont turn on. If I plug it up it will power on the apple logo, and ten seconds later shut off. Then it keeps doing that for infinity. Have I damaged my battery along the way?
@outsourcerepairs7 жыл бұрын
You may have disconnected the power button flex cable, remove the 3 screws that hold the logic board in and verify all flex cables are attached on the rear of the board where the LCD and digtizer flex cable connect. If you have any further questions please message me.
@scientist1007 жыл бұрын
This is an indication of a short. I had an iPhone 6 Plus that was doing that and after careful inspection "on the LCD ribbon cable" I noticed a burn mark that was somehow making contact with one of the pins. I cleaned the area and with a tweezer I broke the bridge that was visible "under a microscope" and after that the boot looping went away.
@BillAnt5 жыл бұрын
The constant boot looping is either caused by breaking the battery cable (or pads), or a firmware error (try reflashing it in DFU mode).
@samuelcholak8937 жыл бұрын
what were the materials you used to unsolder the battery
@outsourcerepairs7 жыл бұрын
Hello, The materials I used are listed in the beginning of the video.
@pedrobeaucaine2585 жыл бұрын
Just thank you : )
@butchpetty79146 жыл бұрын
Hey great video! Very professional. I have a question that you may know the answer too. I do side work with electronics. I received this ipod touch 6th gen as a repair job originally the ipod would only come on with charging cord plugged in, at that time it would show the battery icon in the top right of the screen as dead (smallest amount of red possible in the icon) with no charging symbol. I replaced the battery and now it will charge up but it hesitates like when you first power it on it shows dead on the icon then about 30 seconds later shows fully charged. Is that a calibration issue with the new battery? Thought you might have seen something like this?
@outsourcerepairs6 жыл бұрын
Hello, I've seen the issue you describe(Device turns on & displays low battery) a lot with the Ipod Touch 6th gen after replacing the battery. I do not know what causes the issue but as long as the battery does not drain or appear to be defective it should be okay. If you have any further questions please let me know.
@butchpetty79146 жыл бұрын
Ok thanks alot. I'm trying to do the calibration per apple squad to see if that changes anything. It seems more of a board issue and not battery.
@rocasaja4 жыл бұрын
@@outsourcerepairs I have the same problem. What do you recomend? verify battery´s connections? change battery?
@CaliFZ095 жыл бұрын
Question I replaced the battery on a few iPod 6 touches and all of them turn on but batteries will not charge I plug them in it shows the charging symbol but battery does not charge whatsoever can it be a bad batch of batteries ?
@cjbht19minaret5 жыл бұрын
Hey, So I was doing this myself and I accidentally ripped off the middle solder pad on the motherboard. Is there a test point i can jump to? I couldn't find a board diagram and im not sure how to test it.
@ilovemybluechucks3 жыл бұрын
my ipod is in bootloop. please help
@robmoser44852 жыл бұрын
Wish I had the money to get mine fixed
@mavamQ3 жыл бұрын
At 7:13 hes aays. " this s a dot connector repair" What does that mean.
@outsourcerepairs3 жыл бұрын
Lol I meant to say dock connector.
@RS250Squid5 жыл бұрын
Replacing the battery in my 6th gen IPT tomorrow. I'm not giving Apple any more of my money.
@Malabus735 жыл бұрын
I haven't got the tools or patience to complete this task. My iPod touch will be send to a technician.
@self-righteousideologue93983 жыл бұрын
Literally no company in my state does this, nor can I find any directions on the apple website to send it in too
@outsourcerepairs3 жыл бұрын
I can perform the repair for you if you like. view the link below: outsourcerepairs.com/collections/apple-ipad-ipod-iphone-repairs/products/apple-ipod-touch-6th-gen-battery-replacement-service
@self-righteousideologue93983 жыл бұрын
@@outsourcerepairs - Perfect. I'll be in touch
@lepantobenguet55025 жыл бұрын
2ML MG Chemicals #8341 Flux & 4" Chipquik Alloy and Ipod touch 6th generation battery. I'm from canada and I ordered these items on march 17 and trying to get in touch to ask whats up with my order but haven't received any reply yet. I sent an email 3x already. Could you enlighten on this please
@vanlee17005 жыл бұрын
How much do you do it for
@warriordrum3 жыл бұрын
Unedited low effort video that is clear and concise. The hot air gun is running the whole time....no biggee I guess but again....no editing. Useful and appreciative however.
@outsourcerepairs3 жыл бұрын
Thank you for the feedback. I'd disagree with you when you state no effort but I respect your opinion. I leave the hot air gun running while I perform repairs if I am going to be using it.
@louisle91625 жыл бұрын
im scared of soldering... =\ and i have an itouch i need to fix T~T
@oliverristaino36275 жыл бұрын
for me i was replacing the screen and, as i was taking out the battery i didn't heat the back so i cut into the battery with tweezers and it lit on fire...............
@BillAnt5 жыл бұрын
I can just imagine your face when that happened. Anyway sorry to hear that. Maybe next time take it to a local repair shop, and for a few dollars they'll do it right. ;)
@oliverristaino36275 жыл бұрын
@@BillAnt Yeah, i kinda didnt think it was that bad, like it would work out. But no, that things toast now. Unless i bought a new battery and solder it, but its not worth the effort. But the battery lit up like a firework it was cool in that sense.
@BillAnt5 жыл бұрын
@Im Luma < Basically the solder under the connector flowed and shorted out the (+) and (-) terminals frying your battery. You've gotta be really careful with that, though usually it won't blow up completely, it could shoot out some nasty flames an smoke. Nowadays a local shop will do it for so little money that's really not worth wasting your time, plus messing it up. ;)
@BillAnt5 жыл бұрын
Gotta love that "aftermarket" battery at 16:53 xD (model numbers erased for customs purposes). But hey if Apple doesn't sell their original, then an aftermarket will have to do. ;)
@DINGDONG-yf2xp2 жыл бұрын
I can't find anyone to replace it for me cause they are afraid they ll break my screen
@outsourcerepairs2 жыл бұрын
Hello, I can replace t he battery for you. You can view the mail in service via the link below: outsourcerepairs.com/collections/apple-ipad-ipod-iphone-repairs/products/apple-ipod-touch-6th-gen-battery-replacement-service
@raudelgalicia79086 жыл бұрын
Would a blow dryer will work
@suzesraccoonjs64656 жыл бұрын
Hello! Yes a blow drier will work but dont do it too much lowest setting is best
@iggynub4 жыл бұрын
Not to melt solder.
@DiegoIzquierdo-m3v Жыл бұрын
battery goes down fast in apple ipod touch 6th gen
@outsourcerepairs4 ай бұрын
Yes it does. If possible replace your 6th gen iPod with a 7th gen.
@idawilcox5275 Жыл бұрын
Good Job but team to much for me. Ill just get another ipod or get a professional to do it
@outsourcerepairs4 ай бұрын
Thank you for the feedback.
@benbrown22813 жыл бұрын
Well that didn’t go as planned, replacement battery didn’t even switch the unit on.
@CulturedWhiteBoy3 жыл бұрын
I've never owned or used a heat gun or a soldering gun. No wonder I've never been able to fix anything electronic.
@Apple_20483 жыл бұрын
iPhone battery replacements and such are much, much easier. No soldering needed.