How to generate 100% pure 1Hz clock pulse using 4060 IC & crystal by Inventive Technical Support

I have made a project which is 100% pure 1Hz clock pulse using 4060 IC and crystal oscillator.This Circuit Works as pure 1Hz clock pulse. In the next video I'll made 00 to 59 Counter , 00 to 11 Counter, 00 to 23 Counter.
we can generate this 1Hz clock pulse using 555 timer ic but the clock pulse of 555 timer ic is not 100% pure 1Hz clock pulse.that's why I'll use 4060 frequency divider IC and 32768Hz Crystal Oscillator.
If you like to see my video then Please SUBSCRIBE to my channel & Comment for more information about Electronics Project.
This circuit can be easily made at home. You can made it too. It take some component to make it which I used.
1. 4060 frequency divider IC ( 2 Pcs)
2. 32.768 KHz (32768Hz) Crystal Oscillator
3. 1 MegaOhm Resistor
4. 22pf Capacitor
5. Yellow LED (5mm)
6. 9 volt Battery
7. Some jumper Wire
8. Brade Board
Circuit Diagram : drive.google.c...
Please SUBSCRIBE to my Channel (INVENTIVE TECHNICAL SUPPORT)
and follow me into my social accounts given below.
Thanks for watching this Video.
Facebook : / pallab.sarkar.378
Instagram : / _its_015
2nd KZbin Channel : / @flashy_filter015
Instagram : / flashy_filter015
1. 555 Timer IC Blinking LED Astable Multivibrator : • 555 Timer IC Blinking ...
2. Auto On Time Delay Circuit Using 555 Timer IC : • Auto On Time Delay Cir...
Song: Mike Leite - Summer Vibes
Music provided by Vlog No Copyright Music.
Creative Commons - Attribution 3.0 Unported
Video Link: • Mike Leite - Summer Vi...

[@ccv3237]

Thank you very much. I will wait your mentioned next 00 to 59 counter video.

[@its015]

Yes 😎😎

[@rrentertainment7790]

Yeah i'm also need to know... that'

[@johnmacey2095]

And for the best available accuracy/stability at a reasonable cost, you need to get a GPS receiver and antenna module as your clock source.

[@LeeThayer-nn5ye]

Perfect, and accurate, thank you 😀

[@its015]

Welcome 🤗

[@jozefnovak7750]

Super! Thank you very much!

[@its015]

Welcome 🤗

[@qwlol]

Very helpful thank you!!

[@its015]

Thank you 🙏

[@johnmacey2095]

Not sure what you mean by "pure"? If you mean a nice 50% square wave, then fine! But if you want an accurate 1 second period, then your circuit will probably only get you about 20-50 ppm accuracy/stability. Have a look at a $10 DS32KHZ integrated TCXO chip. That will get you 2ppm accuracy and stability over a big temperature range.

[@its015]

I'll try. Thank You 🙏

[@ucquannguyen7613]

Your video helped me a lot but i just dont know how did you calculate the capicitor and resistor for CTC and RTC pin and why you don't use resistor for the RC ?? pls let me know

[@its015]

Since I have used Crystal in this circuit, I have used this Resistor and Capacitor. you can use any Resistor 500 Kilo Ohm to 1 Mega Ohm and any Capacitor 22pf to 100pf If you want.

[@ucquannguyen7613]

@@its015 Thank you so much but i just wnna know that why u know we can chose Resistor 500 Kilo Ohm to 1 Mega Ohm and Capacitor 22pf to 100pf. Do you have any formula for it ??

[@malekkharcha]

@@ucquannguyen7613 just check the Datasheets

[@jumbo999614]

1 pulse equal 1 second?

[@its015]

Approx 1 seg

[@yeshii7249]

It's not generating pulse what should i do...i used 33pf capacitor

[@its015]

Do Check Crystal .

[@yeshii7249]

Can you please help me out with this it's an urgent project

[@its015]

@@yeshii7249 Send me Your Project Image or Video Instagram : instagram.com/_its_015/

[@rajakjasraya1978]

Hello apane a kit banai he achhi he par A kit me 1 gante me 3600 secend Hoi ti he par a kit mene banai he par he kit 1 gante me 3597 secend chalti he to aab me kya karo

[@its015]

Kabhi kabhi crystal oscillator accurate 32768Hz hota ni hain khas karke local walla toh kabhi ni hote. Fir 1M ohm resistor, 22 pf capacitor, ya v accurate hota ni hain. 5% - to 10% tolerance hota hain Sir ji. 😊😊😊😊😊 By the way Commant karne k liye dhanyavad. 🙏🙏

[@johanwahyudi8508]

Gunanya buat apa?

[@its015]

It is used to determine the seconds of the clock.