OK.....So the plastic knife serves....Absolutely No Purpose! Got It!
@slayer41183 жыл бұрын
Just in case you splooge too much
@theshortgolfer8687 Жыл бұрын
How many Ford Focus drivers watching this? =(
@PrecisionReplacementParts5 жыл бұрын
It helps to tape down the weatherstrip with painters tape so the weatherstrip stays in place. Cure time is 1 hour.
@maplesden67684 жыл бұрын
i went to your web site, i am looking for some weather stripping for my 97, ford, areostar doors. apparently "they" do not make it any more. can you help?
@osita395 Жыл бұрын
I was looking for this answer. Do you leave door open while it cures also?
@osita395 Жыл бұрын
Do you leave door open until glue dries and how long?
@PrecisionReplacementParts Жыл бұрын
@@osita395 Yes, leave it open for about an hour which is the cure time.
@meekmond72053 жыл бұрын
Trying to be smart: disposable flat piece of flat wear Everyone else: plastic knife
@no_handle_required4 жыл бұрын
That 3M is awesome until the day you want to remove and replace the weather stripping. "Sparingly" is an understatement.
@MotorsportCreative3 жыл бұрын
Just curious, but is that from personal experience?
@slayer41183 жыл бұрын
G2K
@gailpeterson37472 жыл бұрын
Just what I need to find. I noticed my door seal starting to pull away just like this one. Quick and easy application--thanks for the video!!
@jamesolelo44062 жыл бұрын
Just tape the areas vulnerable to sticking out so you know everything is under pressure and will stick evenly
@sgower4145 ай бұрын
No loud subscribe-to-me messages. Just got right to it. Easy to follow. Nice instruction to let the glue dry for a minute or two before pressing the weatherstripping in place.
@rhettoracle96795 жыл бұрын
The 3M clear exterior trim adhesive also works well, and thicker to stay on vertical surfaces, but larger nozzle. Peace
@trc56944 жыл бұрын
Thanks! I purchased the same Adhesive and was looking for a video like this before application.
@petervonpanda4 жыл бұрын
It held up nicely on mine. Hope it works well for you!
@sotechy922 жыл бұрын
Nice video, about to do this on my top front windshield adhesive on my Corolla 👍🏼
@iprobablyforgotsomething8 ай бұрын
As a fellow Corolla owner, I hope it went well for you, and will for me also! x'D
@ismailkhan77554 жыл бұрын
Helpful this video what I want Thank you so much,
@MarzNet2563 жыл бұрын
Awesome. Just did the rear passenger door seal on a 2006 Matrix. Following your advise, came out perfect. 🔧
@petervonpanda3 жыл бұрын
Nice! Makes a difference when things are secured in place
@jamesbolotenko34602 жыл бұрын
watching this video to do the exact same thing, your comment caught me off guard lol
@yellobello1 Жыл бұрын
@@jamesbolotenko3460 05 vibe join the club ❤
@jaimedpcaus13 жыл бұрын
That looked quick and easy! 👍😊
@jeffreygrullon29628 ай бұрын
thank you for the video...I have an idea for anybody that just watched this. if you can afford it buy the weatherstrip from the dealer. then you clean all the old glue off. then you do what he did with a. brand new weatherstrip. your car door will thank you. if its just a quick fix this will hold up but not as long and won't bring that nice thump a new one would bring.
@odysseylexus3 жыл бұрын
Can I have the rest of your tube? :D Just kidding. Honda just informed me the glue and labor together is $200. Thanks for this video!
@coolhandbane3 жыл бұрын
That's funny. Honda told me the exact same amount for my driver's side weatherstripping on my 2017 honda civic.
@jaceinlow89803 жыл бұрын
Black rtv also works almost the same, and a little cheaper
@Dlogreen2 жыл бұрын
rtv has nothing on this stuff,. t's essentially contact cement...once they are together you have to destroy it to separate the parts
@speakbigtruth93834 жыл бұрын
This guy never used this product before but he is an expert that can teach us how to do it! 😁😂🤣😄😅
@DAnderson410 Жыл бұрын
I’m assuming you have never created content and published videos before. And you are the expert on KZbin videos?
@speakbigtruth9383 Жыл бұрын
@@DAnderson410 I like the comment. However, it’s incorrect for several reasons. First , I have been creating KZbin videos for a long time. Secondly I’m not teaching you how to make a KZbin video. Lastly, if I had never made a KZbin video and I was trying to teach you how to make one then you would see my exact point about what you were doing.
@GameGasmTrailer Жыл бұрын
That means he figured it out on his own without needing to watch someone’s KZbin video to do so. Ain’t nothing wrong with that. W Video
@GameGasmTrailer Жыл бұрын
that comment was less thought through than you’ve realized. Trying to dunk on someone while being the one who can’t figure out how to apply adhesive. Otherwise you wouldn’t be searching for this content. Smh.
@speakbigtruth9383 Жыл бұрын
@@GameGasmTrailer He is doing for the first time on this video.
@peterrudy92072 жыл бұрын
Maybe to have used something like the old clothes pins used for hanging clothes outside . Or I expect they have miniature plastic clamps to use .
@VideoNOLA2 жыл бұрын
If that's not just repackaged rubber cement glue, I don't know what is. Looks and acts the same!
@colbyd7814 Жыл бұрын
taste the same too
@Rippedjohniii293 жыл бұрын
Can I use this on outside parked car in 50-60 degree weather or should I wait for warmer day ?
@VincentScales4 жыл бұрын
Did my driver side door, so far so good! Might have to add a little more later.
@margaretmitchell76033 жыл бұрын
What glue did u use please ?? Just purchased the front Holden Cruze shields but they come with nuts an bolts an being a woman I don't own a drill etc so thought maybe I could stick em on like my previous car had them attached ?!
@abdirizakful2 жыл бұрын
@@margaretmitchell7603 buy weatherstrip adhesive from local auto parts
@EddieH7112 жыл бұрын
I'm about to use this adhesive for my Honda Civic. Just to confirm, once you apply, wait 60-90 seconds to dry then bond the rubber strip to the body? Thanks!
@petervonpanda2 жыл бұрын
Yep, that's what I did and seemed to work great. It was about 70 degrees, so if it's a really hot day, maybe wait less time.
@garylbowler3 жыл бұрын
Fantastic! Thanks for the direction as I’ve never had this issue before! Much appreciated!
@SmoziesInk4 жыл бұрын
Is this the same fix for the rubber gutters above the car door?
@MarzNet2563 жыл бұрын
Should work for that as well.
@ll0lllo4933 жыл бұрын
My car is moldy 😟
@micahbender10644 жыл бұрын
This is exactly the video i was looking for. Thank you :)
@soumyabrataroy30652 жыл бұрын
Hi, Can this be used for Roof rubber seals ?
@djmoss934325 күн бұрын
Awesome video, planning on doing this to the bottom weather strips on the bottom of 3 of my doors on my 08 Pontiac GT 🤞🏽
@dontbeabeta421217 күн бұрын
Thanks for the video 👍
@NuMooX4 жыл бұрын
BMW are notorious for this.
@rodneysmith2473 жыл бұрын
When I bought a minivan most of the lower liftgate weather striping was all torn off or missing. Do you if that will cause rattles going over bumps and pot holes? Great video 👍
@MarzNet2563 жыл бұрын
If definitely could cause rattles. See if someone sitting in back can locate the noise.
@overtonesnteatime1982 ай бұрын
wrong wrong wrong. this is bad and you missed important steps.... amazon associate and the brain to go with it.
@brandonpero87424 жыл бұрын
What if it's on the bottom side of the door and it has those stupid little plastic clips?
@coachsamempowers58374 жыл бұрын
@brandon perault Did you find a fix for the clip issue? I watched a video that said there are holes on the rubber that the clips go in...
@davidfierro36505 ай бұрын
Can any suggest the best product to glue back a small rip in the rubber seal of the door??? It's the thin rubber seal that surrounds the outer door trim.
@71dodgecoronet845 ай бұрын
Would b better if you cleaned both surfaces 1st...also when about to press put a thin film on either side
@TBoy2052 жыл бұрын
How long before you can close the door? Instructions don’t say anything about that
@calvinhang9 ай бұрын
Is there any way to remove dried glue on the trim? Getting OCD from the excess adhesive that somehow dried up on the mold trim.
@BestQoqaj8 ай бұрын
What is the difference with black silicone with black glue? ⚫
@aarcusisloading99914 жыл бұрын
Spoiler the knife died during filming and a look a like was used but all of the lines were cut.
@petervonpanda4 жыл бұрын
The CGI just wasn't up to par.
@shill6449 Жыл бұрын
Nice product, but pricey. There are less costly alternatives, same spec.
@gitmoholliday57645 жыл бұрын
if you get it on your hands.. will it stick and make bodyparts joined together ? ( would be nasty if you need to drive that old car to the hospital with your elbow or foot attached to your nose or maybe a Chihuahua )
@MarzNet2563 жыл бұрын
Just don't get it in your eyes 🔧
@TFreshour08 Жыл бұрын
For those wondering, the 5 fl/oz bottle is massive lol. But at least I have extra.
@thegravityrebel Жыл бұрын
Thanks for the video. I bought it from your link.
@hugeCRSfan694 жыл бұрын
will this adhesive glue a weatherstrip to plastic trim? i have a chevy express van and there is a roof drip weatherstrip that sticks to that top plastic halo trim above the rear doors
@petervonpanda4 жыл бұрын
I would think so
@joshuaychung5 жыл бұрын
Was this Maserati not garaged? It has all these small issues (e.g. oxidized headlights, peeling rubber weatherstrips, etc.) that are typical of the cars that are not garaged.
@sasazapadnik93353 жыл бұрын
And don't forget it is a Maserati.
@paulbiers7 ай бұрын
never glue the gasket. just replace it with a new one.
@jb19954 жыл бұрын
This was a big help.Thank you my panda brother!
@petervonpanda4 жыл бұрын
My pleasure! Thanks for watching!!
@countfloydschillerhorrorth2090 Жыл бұрын
Mine lasted about a year and now i'm back on looking at videos.
@sdsturges2464 Жыл бұрын
the smell of that stuff is terrible .but it does work good .
@JohnAnderson-sm8jl2 ай бұрын
Great video. Thank you!
@thesninjaxoxo Жыл бұрын
My brand new Honda after 1 month…..
@MrMakaveli27863 жыл бұрын
🙋🏻♂️excuse me. What was the knife for ?
@petervonpanda3 жыл бұрын
I was going to use it to spread it but didn’t need it
@kevinhood97812 жыл бұрын
What kind of knife is that?
@karronlaneNOLA2 жыл бұрын
nice. thanks. i have some work to do.
@U2BER2012 Жыл бұрын
Will 2 part epoxy work; just as well?
@annamcdonald6311 Жыл бұрын
Dont you have to clean or scrape the old adhesive?
@timmy968152 жыл бұрын
Hello will contact cement work.? I loved the video
@snackymcgoo1539 Жыл бұрын
Thank you, I am going to order some.
@staceysing42632 жыл бұрын
Finally, the video I was looking for! Thank you sir!!
@gpopscastro8664 Жыл бұрын
Where do I buy this glue
@kaylanoorlun2 жыл бұрын
Are you a dentist?
@gregs_garage3 жыл бұрын
Messy
@LJ555553 жыл бұрын
Do you think will work for the rear window sealant (top of rear window) of my Mercedes ClC?
@bootheoutlaw75968 ай бұрын
Where did you purchase this from?
@petervonpanda8 ай бұрын
I got it on Amazon!
@believeinjesus8300 Жыл бұрын
Cool 😎
@arungoel11262 жыл бұрын
P
@michaelmclaren89503 жыл бұрын
Glue works too
@anthonymarino42603 жыл бұрын
now I understand thanks
@Mike-012343 жыл бұрын
Go easy on the adessive don't need big job getting it off later
@petervonpanda3 жыл бұрын
Good tip! Less is probably more.
@yodoublep71973 жыл бұрын
Can u use this on rear passenger window on two door car
@jd66605 жыл бұрын
Thanks👍
@yves35604 жыл бұрын
You could have shown that in 30 seconds flat.
@kalegalremal5 жыл бұрын
Good job.
@JGC_TV4 жыл бұрын
Hey Peter von Panda! I bought the same 3M weather stripping glue but it is wrong for my project. What I need is something that will keep the plastic in-place against the inner door that covers the door components. To be clear, Im referring to the plastic that you find when you remove the door panel sometimes called the "door card"...the plastic covers the actual metal door panel...between the "door card" and the door... hope that helps. the 3M hardens, I need something that stays tacky without hardening so as to not have to reapply each time I remove the plastic. thanks
@The_Car_Gods_78144 жыл бұрын
Try looking for Butyl cord, black and round. Commonly used for "shower curtains" as we call them in motor vehicle production in the UK.
@notreal52994 жыл бұрын
i used high temp bearing grease. seems to be working.
@williamlookinggoodoldguy19642 жыл бұрын
Ok
@arcadiomunoz60893 жыл бұрын
Good looking out man!🤙🏽
@raymondperez35534 жыл бұрын
Hi Peter , Did you Need to Clean and prepare the Surface before applying the product??...
@petervonpanda4 жыл бұрын
I didn't do any prep and mine is holding up fine
@raymondperez35534 жыл бұрын
@@petervonpanda "Thanks Peter!! I'll Order Some for My Ride!!👍👍😎
@Eatinbritches4 жыл бұрын
Maybe if there's lots of caked on gunk, you can take a dremel with a wire wheel to it. Maybe touch up paint that you burn through.
@RS-hz1yi2 жыл бұрын
@@petervonpanda can it work to seal a tear in the seal itself?
@yagousera5 жыл бұрын
Lets see, Why show the "Plastic Knife" if you weren't going to use it ? It was suppose to be used to spread the glue flat so it would dry and bond better. Oh, well there's always a "Video" of how not to do it.
@petervonpanda5 жыл бұрын
I was going to use it but didn’t need it
@David-kk4dr5 жыл бұрын
Weren’t you supposed to remove the old glue first?
@yagousera5 жыл бұрын
@@David-kk4dr - Yes If you can but alot of the times it's stuck on one side that if you try to pull it off I'll rip the rubber with it, still a video on "how not to".
@jerryx20003 жыл бұрын
LOL the moral of the story 1) never buy a car owned by a Chinese 2) Could you make a video on that fake Apple Watch