How to Install a Creality Filament Detector on an Ender 3 V3 SE

Рет қаралды 12,298

Күн бұрын

Пікірлер: 51

@benemery1644 8 ай бұрын

Thank you! This is the only video I can find installing it on this model that's actually correct and also easy to follow

@mrsalustiano 8 ай бұрын

Thanks for the video, it was the only one I found explaining how to do it correctly.

@fuelmachine01 5 ай бұрын

Hello Dean, I really appreciate your video, with it I was able to make the connection without any problem. Thank you very much for your support!❤

@DeansNScaleTrains 3 ай бұрын

Glad it helped

@cesarepassarelli1106 6 ай бұрын

Great video, thanks, im installing tonight, you made it very thorough and anytime i had a question you answered it pretty much seconds after i thought the question to myself haha thanks again !

@danward6420 7 ай бұрын

I have seen on other 3D Printers a filament detector and would like to add one to my printer. Thanks to your video and information, I’ll be able to do that.

@NoThingL0se 2 ай бұрын

You can hide the sensor cable by passing it through the channel under the upper pole.

@NiliPFerd Ай бұрын

Now this is a video I can follow! Thanks.

@hevak17 8 ай бұрын

Thank you mister. I bought and install the detector as well

@tonywharton5220 4 ай бұрын

This is definitely the best video ✌️

@DeansNScaleTrains 3 ай бұрын

Thanks for the endorsement. Much appreciated.

@thetomer9786 2 ай бұрын

Thanks for the video guide, it was really helpful!

@Fochis01 7 ай бұрын

Thank you very much, sir. Your video on installing the sensor has been really helpful. Thanks!

@tonyballeras 5 ай бұрын

ah ok got it. its on the description

@s_gwalls6106 4 ай бұрын

There's clips under the top plastic piece and one on the back to hold the wire for the sensor instead of it dangling all ugly like that

@Doboy64 9 ай бұрын

Thank you for the great video. Question: When you reload the filament after the sensor trips and pauses the print, do you have to use the extrude command or does the machine automatically prime the nozzle?

@DeansNScaleTrains 9 ай бұрын

Don’t know. I need more experience with it. Anyone else know?

@techyhunter7581 5 ай бұрын

I must have the older model of the v3 se. Mine doesn’t have a passage for hiding the wires on the top piece and no opening to feed the wire into and down the gantry without crushing it.

@Santos47 5 ай бұрын

Yo tampoco, lo tienes que poner por fuera y apañarte con el cable colgando por la columna.

@gunerkahraman3761 5 ай бұрын

Thank you

@tengteng8640 3 күн бұрын

Thank you grandpa

@tonyballeras 5 ай бұрын

thanks where did you buy your detector?

@DeansNScaleTrains 5 ай бұрын

On Amaxon

@CrymSyN007 6 ай бұрын

i installed this on my ender3v3 se and its not working, im assuming i have to upgrade the firmware, anyone know where i can find the correct firmware?

@westonsmith6925 5 ай бұрын

Comment in here if you find the answer, it also does not work for me and I'm not getting any help

@electroshow4192 9 ай бұрын

Como SE pone en modo usb dfu la crealy 3 v3 se

@SOSmysteries 9 ай бұрын

Thanks for this!

@WatchingYoutube123 6 ай бұрын

Where on gods earth is that slot in the upper piece of the cable ???? No matter where I guided the cable there was a gap. Please please please show me where the slot is. So I can guide it through. Thank you 🙏 OH and another thing, I was unable to remove the fan wire or cable from the motherboard and it GLUED to the base and I just awkwardly had to move it to the right trying not to detach or rip of the fan cable from the motherboard. Is it normal for it to be glued ?

@DeansNScaleTrains 6 ай бұрын

I have posted a public post on my community tab which I hope might help you find where the cable slot is. It took me awhile to figure it out where it was when I assembled mine. Creality tends to fasten the cables to the mother board with white hot-melt glue. You can usually remove this by grabbing with pliers. If you're careful it shouldn't hurt the cable connector or the slot it goes into.

@DeansNScaleTrains 6 ай бұрын

Opps, forgot to mention the public post has a photo of my assembly.

@electroshow4192 9 ай бұрын

Display tft35 e3 for creality 3 v3 se

@Krohling 7 ай бұрын

I am unable to fit the top frame back I have to carve a small dent under the frame where the cable/wire comes to be able to fit the frame

@DeansNScaleTrains 7 ай бұрын

Running the cable is a little trickie, but it does work. Your way is also a solution.

@WatchingYoutube123 6 ай бұрын

That’s the exact same problem I had, I don’t know if I should carve a piece out or if I should keep struggling trying to find the slot in the upper piece to guide the cable through

@Krohling 6 ай бұрын

@@WatchingKZbin123 there is an intersection of three or so plastic pieces coming from the three holes, I carved the plastic there

@flaviomalvestiti2053 3 ай бұрын

Thank you Mr. Dean. (Sorry I'm not english fluent, so I didn't get your last name.)

@DeansNScaleTrains 3 ай бұрын

You’re welcome!

@ravb.7700 7 ай бұрын

Anyone managed to get this working with the Ender 3 V3 SE and the Sonic Pad? Installed it all today with the help of this video and nothing :( Doesn't seem to do anything.

@DeansNScaleTrains 7 ай бұрын

I have never tried Sonic Pad. Sounds like it isn't compatible.

@ravb.7700 7 ай бұрын

@@DeansNScaleTrains I was able to work it out. Just had to add some gcode into the printer.cfg file.

@electroshow4192 9 ай бұрын

Marlin

@ardaucr 9 ай бұрын

its false you cant plug that there the plug is 4 pin but your cable is 3 pin you must plug the cable to next to edge screw three pin slot ı do it now and its work with that

@sACLeFR 8 ай бұрын

Can be 2 different version of the filament sensor ?

@LM-qe8kv 2 ай бұрын

Whilst I appreciate the time and effort you've taken to produce this tutorial, it's a complete waste of time. Like others have explained my fan cable is firmly locked in place and cannot be removed. The bigger issue is that the 3-pin cable does NOT fit down the vertical extrusion like you have shown. The cable end (plastic) is far to big to fit down - I'd show a photo but KZbin sucks and won't let me attach an image to this post). Now I have to reassemble everything and hope I haven't screwed up a printer that was working perfectly prior to trying this waste of time. I'm just going to throw my runout sensor away; I don't need this crap in my life. P.S. After reassembling my printer, my levelling is way off, it was perfect before now it's all blue and yellow.... what a huge pain in the ass, all for nothing

@DeansNScaleTrains 2 ай бұрын

On assembly, they often hold the fan cable to the printed circuit board with a blob of hot glue. It looks like a white blob. You can take a pair of needle nose pliers, grasp the blob tightly, and pull it off. But you can just leave the fan cable attached with the cover plate hanging if you don't want to do that. You may be trying to push the wrong end of the cable through the extrusion or it may be positioned incorrectly. One connector on one end is larger that the other. If you got the kit from Ender, I can assure you it will work.

@karlbassett8485 16 күн бұрын

The tiny diagram that came with the sensor kit shows it connected to a three pin socket half way along the LONG side of the mobo, but in this video it connects to the correct sized four pin (but only three wire) socket on the short side of the mobo.