जैसा एंकर बोलते हुए बता रहे हैं कि एक बोल्ट टाईट करने के बाद क्रॉस में उसके सामने वाला बोल्ट टाईट करना चाहिए लेकिन वीडियो में जो व्यक्ति बोल्ट टाईट कर रहा है वो ऐसा नहीं कर रहा है इसलिए आपको पहले अपने इस साथी को भी ट्रेंड करना चाहिए।
@lalitrawat902 жыл бұрын
Mistakes that were made while installing hilti anchor bolt: 1. Machine was vibrating way too much which may lead to loose fitting. 2. You skipped video cleverly when he was hammering anchor bolt with the help of hammer. Bolts were not going in even after applying enough force, and you did cut them off as we can see on 4:22 , which creates doubt that your drill bit was quite old and has lost sharpness on tip. 3. Fitter was hammering on nut after keeping them on edge which I totally understand that he wanted to save bolts thread. But if you notice that those anchor bolts dont have thread outer side and have less diameter also. That is because you can hammer the bolts, since there is no thread outside have lesser dia, you nut can come outside without any trouble. 3. You must have to tight nuts and bolts with Ring spanner only. Not with D-Spanner.
@izmirfication Жыл бұрын
yes ,I appreciate all the work done at field but not getting the anchor bolts red mark as close as possible to concrete surface is very crucial as this is explained above, it is not an acceptable excuse like the driller couldn't get deeper..
@PrashantKumar-lx2kr2 ай бұрын
Useful,thank u so much
@psingh5941Ай бұрын
Sir stone Bolt kya hota h
@TEJARAMCHOUDHARY88 Жыл бұрын
Mujhe bnana hai Bhai
@SudebModeАй бұрын
Good job 👍 Good is good 24 Mater H Bim available hi please message
@mdshahzad4267 Жыл бұрын
Ghar ke chokhat.kalam me kaiise lagate h .kitna inch hona chahiye
@mamtjha9 ай бұрын
बहुत ही उपयोगी जानकारी दी आपने। बहुत बहुत धन्यवाद आपका
@sanjeebtamrakar8610 Жыл бұрын
what about the reinforcement of column when you are drilling the hole? Is it ok if the drill beat crushes the re-bar?
@PrashantKumar-lx2kr2 ай бұрын
Same questn
@sanjaladebbarma350911 ай бұрын
Sir apka drill machine ka price kitina hai or kasa company hai
@RajivKumar-qb7ji Жыл бұрын
How much cost this 04 Nos Anker bolts? (size as per vedio). How much cost of M. S. Plate? (Size shown in Vidio)
@RaviMode-mv1xo Жыл бұрын
hello sar 12 Mater HBame video please
@LITTLEMASTIBAZzАй бұрын
10mm fasner me kitne mm bit daalna he yeh to bata do
@Rabiya-fabrication3 ай бұрын
1000 kg vajhan jhel sakta hai sar 2:53
@ma-lakshmifabricator7549 Жыл бұрын
Overall, this is a highly informative and enjoyable video for anyone interested in fabrication. It showcases your talent and expertise while providing valuable insights and inspiration to fellow enthusiasts. Keep up the great work, and I look forward to watching more of your content in the future 👍👍👍
@Ajaysingh-or7ilАй бұрын
Plate kitna MM hai Sir ??????
@RamDas-vg4xb8 ай бұрын
Shearing load is column?.. column only take axial load and moment due to eccentricity….
@Rabiya-fabrication3 ай бұрын
Kiya ye ek tan wajan jhel sakta hai sar
@ronil_singh Жыл бұрын
Use chemical also for fastener ensuring extra grip
@madanmohan4244 ай бұрын
Contact no mil skta hai kya
@janardanmore66656 ай бұрын
उसमे पिन नही मार दिया
@premjha77222 жыл бұрын
Sirjii flexural test ( Beam ) test kaise karte hai aur vo karne ka reason kya hai uska video banayiye na
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@yasirmahmod6832Ай бұрын
Pls, can i install C channel of gypsum boards by rawl bolts in ceiling ?
@madanmohan4244 ай бұрын
Sir ji aap ka no mil skta hai kya
@mostwanted_00710 ай бұрын
Hello sir! Can we use these types of anchor bolts to hang jhula from ceiling? How much tension load can these take?
@saurabhhadke9009 Жыл бұрын
Thanks sir for this informative video
@shambagel Жыл бұрын
Please make video of staircase bhim making for load balancing old bulding
@anandkashyap46262 жыл бұрын
सर हमको पता नहीं था शटर पति के लिए हमने कलम एक कोना काट दिया मुझे सुजाओ दे
@manojmishra3499 Жыл бұрын
यम नहीं M bolo
@Alokkumar-bd8ye Жыл бұрын
Sir mera ghar ban chuka hai, aur frant me 2 round pillar hai jis par balcony ka pura load hai, avi main us dono pillar me gate ke liye hole kaise karwau. Plz help kijiye
@deepakjha66352 жыл бұрын
video dikhaya to achhe se dikhata. बीच में skip kyu kr diya...😖
@surajsyangtan465 ай бұрын
sir mereko usi tar niche chhatme iase plate me bolt lagana hai u kaise konsa bolt laga sakta hai?
@imdadimmu8741 Жыл бұрын
Thanks for support sir
@surajkuk5048 Жыл бұрын
Sir maine gate lgana h lekin jha gate feet karne h wha beem h agr beem tode g to vo kamjor ho jayga keya kar skte h gate ka 1 side ka weight 100 kg h yaani total 200 kg
@abhishekgiri62073 ай бұрын
Isko bina fixer camical ka use kr skte h??
@mohammadtasleem5690 Жыл бұрын
Sir aap apna number sand kar dijiyega
@jaishrimahatma9643 Жыл бұрын
2 MINUTE KA VIDEO 8 MINUTE KIYA
@adwaitkumar11 ай бұрын
Bhai kya is bolt fastener ke prayog do pillar ke bich me ek aur pillar daalne kar sakte hai.mere yahaan 21 feet ki doori par 9×15" pillar hai.hum first + 2nd floor daalna chahte hai. Is bolt fastener beem me lagaa kar nichey aur upar pillar first floor ke liye kar salte hai .kripaya bataaye
@rbsinghcivilengineeringaca677711 ай бұрын
Deer ish situation mein aap rebaring beam ka use kar sakte hai, Anchor fasteners se jada achha rahega. Rebaring ke bare mein bhi video hamare channel mein available hai aap dhekh sakte hai.
@Mghosalkar29 күн бұрын
Great sir ji Jay hind vandematram
@mohammadtasleem5690 Жыл бұрын
Sir aap apna number sand kar digiyega
@rameshmarupuramesh5683 Жыл бұрын
Do u have any method of Direct tensile strength method and required equipment, please share the details
@mohinuddinshariff52132 жыл бұрын
Hilti bolt aare so much costly,,,ithna nahi hona chaiye is bolt ka
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@yashvantmakwana61292 жыл бұрын
Very good
@chanakyasinha80467 ай бұрын
Nut nikal ke thok sakte hai thread pe asar nahi ayega
@RajaKumar-hz6od9 ай бұрын
इसको लगाने का फायदा क्या है क्यू लगाते हैं ये
@DRAGON_FRUIT_3738 ай бұрын
Bahut achha, Naya kuch sikhne ko mila, lekin mere Ghar banate waqat mistri ne collum ko adha kat ke balcony bana diya
@GovindSingh-yv7tr Жыл бұрын
Your thumbnail photo looking like me.
@kinzaandfizan83937 ай бұрын
Sir in fastners par 400 kg ka main ms gate laga sakte he kya
@gopalkhilwani6023 Жыл бұрын
Sir 4" ki purani chat ki load capacity kaise badhaye
@subhajitpaul2848 Жыл бұрын
Proper bataye par proper dikhaye nahi.
@arunkumardesai72238 ай бұрын
Thanks for helping me Dada 🙏
@prabhanjandalia2366 Жыл бұрын
Good job sir
@devilranjan3362 Жыл бұрын
Anchor fastener size kya tha
@SandeepKumar-gu4mf Жыл бұрын
प्लेट टेड़ा लगा है 😂😂😂
@sanjayvadoliya8598 Жыл бұрын
Nat tait me ring spanner👍use kare
@RAJESHKUMAR-qe6bl Жыл бұрын
🐷🐷🐷हम सर काम करने लिए चाहते हैं
@preetisingh-rq7ph Жыл бұрын
Sir in fastener par lohe ka main gate b lagaa sakte hai ???
@kashi28432 жыл бұрын
excellent video sir, please tell me is there any Indian counterpart of the anchor fastener BETTER or same quality of Hilti fastener used in civil engineering by professionals - pls tell name and model no OR all only use Hilti ??
@vishnuprasad5562 жыл бұрын
sir maine ghar banaya hai lekin chajje main latak beem nhi hai uske liye kya karna chahiye
@dukaleashokdukaleshravan2029 Жыл бұрын
Yeh wedge type anchor fastener hai kya?
@Arifview3333 Жыл бұрын
Bhai ander iron road aygaya hai
@TEJARAMCHOUDHARY88 Жыл бұрын
Mujhe aap se bat Karna hai
@nayankumarsingh8237 Жыл бұрын
200 kg ka door bim ke sath laga sakta hai
@subodhanand8271 Жыл бұрын
रॉड आएगा तो क्या हॉग?
@AmitSingh-th1ir Жыл бұрын
Sir ye fashner कितने के ओर कहा से मिलेगा?
@avinashdubey751 Жыл бұрын
Contact me
@bharatvora16282 жыл бұрын
Supar sir Kabhai hamari mula kat kare...
@farus1687 Жыл бұрын
sir thread k liye lakdi rakh kar thok saktai
@gautamparvindar6061 Жыл бұрын
Bolt grout nhi krte
@sarkarpinaki110 ай бұрын
Very informative video.
@usmangani29752 ай бұрын
Supaer sir
@dukaleashokdukaleshravan2029 Жыл бұрын
Can we use this for conveyor column base plate fixing
@MukeshBarman-f2c11 ай бұрын
Plate kaha milega
@Singh-pq7tk Жыл бұрын
Iss plate ka use kaise hoga.
@surajverma74422 жыл бұрын
Thanks upload video
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@axomorlora78012 жыл бұрын
This wrong bolt
@TechnicalSanjayRefinery Жыл бұрын
👍👍
@nehemiaharrolla61396 ай бұрын
Good information
@dukaleashokdukaleshravan2029 Жыл бұрын
Drill size kya chahiye
@nationalfurnitureandinteri47639 ай бұрын
Very nice video sir
@sandeshkirve13882 жыл бұрын
Fastnor fitting karate samay bolt ke pichale hisse par hammer karana hai ye to nut pe thonk raha hai. Fitter ko achhi training ki jarurat hai
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@basavarajt42 жыл бұрын
Sir pillar structure ke liye konsa size ka bolt use karna hai
@premjha77222 жыл бұрын
Concrete mix design with step calculation ka video banayiye please sir
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@rbsingh7442 Жыл бұрын
Very good knowledge.
@ykjoneja4661 Жыл бұрын
Well explained
@RAJUBESU Жыл бұрын
Can we used as shifting of centre point of columns by hilty?
@RaviMode-mv1xo Жыл бұрын
Good job
@adityasehgal4123 Жыл бұрын
मकान बनने के बाद 2मजिँल पर बालकनी कैसे बनाऐ
@rbsinghcivilengineeringaca6777 Жыл бұрын
छज्जा की सरिया को एक्सपोज कर के steel को welding करना है उसके बाद आप को horizontel beam ka support भी देना होगा sir ji . यदि बालकनी की लंबाई और चौड़ाई ज्यादा है तो .. और यदि स्टील की बालकनी बनाना चाहते हैं तो एंकर फास्टनर बोल्ट लगा कर भी आप कर सकते हैं..
@Ahitesh01 Жыл бұрын
Nice
@NitinSingh00182 жыл бұрын
Knowledge full video 🙏
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@sanjaydubey7791 Жыл бұрын
Excellent
@prakashnayak8692 жыл бұрын
Really knowledge full
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@civilengineeraltaf57592 жыл бұрын
Aap sath me ye bhi batadete ke eska uses kya kya ho sakta hai........
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@imdadimmu8741 Жыл бұрын
Very helpful video
@Vijaykumar-zq3yu Жыл бұрын
Shaandaar video sir jii
@SabirAli-ob6ou2 жыл бұрын
Very good.sir
@whitewalkers97932 жыл бұрын
Sir isme camical nahi dalte kya...
@rbsinghcivilengineeringaca67772 жыл бұрын
केमिकल डालने की जरूरत नहीं पड़ती है
@sudiptachatterjee6730 Жыл бұрын
M16 bolt ke liye drill bit kitna ka Lena parega?
@mohammadhussen9622 Жыл бұрын
16
@keneilhouliesolo1883 Жыл бұрын
Very nice and clear explain... excellent 👍👍👍
@maheeshkumarthapa2 жыл бұрын
Excellent performance
@civilknowledge75342 жыл бұрын
RCC beam and it's steel Design sikhiye sirf 2min👇 kzbin.info/www/bejne/pIPJdGuLYt1saKc
@sandhugaming7892 жыл бұрын
Thx
@pravinahir22962 жыл бұрын
Sir isane kase decided kiya ki 120 jana chai
@rbsinghcivilengineeringaca67772 жыл бұрын
Dear very good question, As per Anchor Bolt Fastener technical specification, already minimum depth of Anchor Bolt given & already marking in Anchor Bolt minimum requirements depth, but different Dia wise depth & strength change hogi ish liye aap ki requirement ke anusar aap ko anchor bolt use karna hai, aur video mein bhi depth ke bare mein bataya Gaya hai