How to install bath exhaust fan Panasonic FV 0511VQ1 or similar.

[@itshemondtime3459]

Panasonic needs to thank you. Their instructions are so confusing ! Thank you!!

[@mistadreadman]

Yes. I went to the Panasonic website and their video is sht.

[@tomdavies5492]

This video was extremely helpful. My electrician installed our Panasonic fan, and I had provided the short pipe to connect to our previously installed flapper vent. The electrician failed to install the pipe, and told me to have an HVAC company install it. The bid I received for that additional sheet metal work was $375?! This video gave me clear instructions, step by step, on how to remove the fan , and I was able to easily add the short section of galvanized pipe to finish the job myself. Saved me $375 and a night's sleep. Now that's a helpful video! Thanks so much!!

[@michaellajiness4189]

That music is solid!

[@MrsAlyKittie]

Agreed! Lol

[@Shad0wC0mpany2]

I came for the install, and then I came again for the MIDI loop. What a fancy party this is!

[@auwtomoton]

So helpful! thank you for making this

[@ilovemywifemost]

It seems like this model was also designed as a retrofit fan. This video showed it as for new construction where drywall had not be installed before. It would be nice to have a video shown as a retrofit where only access through a hole is available.

[@johng2913]

Yes. I will think about it.

[@wayne9903]

ditto here

[@AnAmericanFan]

These instructions are nice for new construction. I have a retrofit with 1952 - 1" thick cement board for the ceiling. The instructions that came with the unit are USELESS. I did my own retrofit to overcome the stupidity of this design for the scenario that I have. Luckily, in this scenario I have access from an attic above. The only thing that might have been helpful was the wiring diagram (however, I already know how to do this). Nice unit, terrible instructions! The job is finished, no thanks to Panasonic's manual.

[@skylarsky3173]

Thank you so much!! This tutorial helped me with my install.

[@07181127]

Trying to find one of these videos for Panasonic fan with light and modules for the wiring

[@JoaquinChea]

Need a video for installation on retrofit/post wallboard installed.

[@David2151999]

Good stuff John G

[@tomhurley6004]

This video is for new construction. I just attempted to install this fan by replacing an old fan. The EZ rail system is very delicate and needs to sit on top of the drywall ceiling. Attempting to mount the back portion of the fan outlet and wiring junction box did not work. I mounted it on top of the EZ rail system and used the self taping screws provided. NOTE: It's a ONE-TIME shot using these self-taping screws - if something doesn't fit right and you need to remove and reinstall the screw, it no longer works and then you get into further trouble since the screw will not keep the fan outlet assembly fastened to the EZ bracket. This is when the trouble starts. It took an inordinate amount of time to get this installed - something near 8 hours because of all the nuances. Sure its easy when you have no drywall and are not working on a ladder or in the attic. I need to go back again to attempt to get this cleaned up and properly installed. I am not too happy with the overall installation of this system. I think it should have been much easier!

[@mistadreadman]

I HAD THE SAME PROBLEM. A RIDICULOUS AMOUNT OF TIME WAS WASTED.

[@ecoprops8097]

it doesnt seem the 2 self tapping screws at time 3:32 actually hold the fan up, like the 2 on the other side. At 4:32 you push up on that side and it doesnt seem secure? I'm about to put mine in but dont see what holds that side up? Am I missing something? thx, great job also.....Mike

[@johng2913]

Look at the upper fan body and the side guide already installed. You will see what holds the fan body to the side guide.

[@shaynajagger7737]

thank you as it wasnt an ideal video, it was helpful. so i checked out ur page.....i just subscribed. thanks again

[@Swiftler.13.TS12]

Thanks for the video! Where do you do the cut out once the drywall goes up? Seems you wouldn't want to cover the frame of the fan body so it could be easily removed, so around the outside of it and the bracket?

[@MiltonRoe]

Exactly what I don't get. The vent is now flush with the bottom of the joists. Now install some strapping and your drywall, and the vent is now.... it's now around an inch and a half inside the ceiling. How tf is this supposed to work? I guess the vent cover can slide down a little on its wires to accommodate the added height? But what about the gaps between the strapping and the drywall? Won't it pull air in between them?

[@AgentOffice]

@@MiltonRoe fill gap with foam

[@wayne9903]

Thanks ! Helped a bunch, but we had to do and R&R and approached it a bit differently

[@joebklyn8458]

It says in the instructions to NOT to put an elbow on it right at the fan outlet. It says to give the fan at least 3' before you put any 90-degree elbows in.

[@johng2913]

It is Panasonic recommendation, but outside vent outlet already installed and no other option to vent it out.

[@Michael_Schofield]

Great. When YOU install it, remember NOT to do that. What are you chastising him via comment?

[@vincevega0]

04:38 machine screw into wrong hole? It was originally in hole where white arrow was pointing.

[@johng2913]

Both holes do the same job if they tightly connect both parts of the fan.

[@dean3583]

Good video. I would add a 4" insulation sleeve tube over the metal duct.

[@joecox9958]

thanks a lot!

[@rimiastiho4743]

Simple and detailed Thank you

[@-8_8-]

Lol, I'm just guessing it didn't come with that connector for the cable coming into the electrical box. Thanks for the vid.

[@williamsparkes]

After installation my light, night light and fan operate independently from their own switches. When I turn on the heat switch only, both the fan and heater operate. Unable to get heat to operate by itself. suggestions?

[@isamora4685]

Good video

[@RetroTechIIfx]

I love the MIDI music on this tutorial.😁

[@Rocky-xx2zg]

Anyway to override the Heat Temerature Sensor?

[@charlesscioli5268]

Hi Do you have to leave it down a 1/2” on your framing for sheet rock when you are doing it in new construction? Not a retro fit? Thank you

[@itshemondtime3459]

Don’t believe so

[@victorvek5227]

I’m in the same boat right now. So I’ve attached the fast bracket to the joists and the fan housing up to the bracket (per the instructions). But nowhere in the directions does it specify this aspect. Did you drywall over the flange and right up to the inner part of the housing? Does the grill still firmly attach being 1/2” recessed above the ceiling drywall? I’m stuck

[@rebeccajohnson1368]

How to airseal the cracks etc. So that moisture in thebathroom won't travel up to the attic

[@life_score]

Instructions recommend caulking on the edges (against ceiling I believe).

[@AgentOffice]

Foam

[@jimmyjamesl2318]

The contra video game theme song?

[@juliancasey501]

Good video, lamentable AI voice over. I’ll re-do it for free.

[@scottmeeboer3094]

If you're an hvac installer and are installing these over and over again, it's a decent design. But if you are only installing one, this an overly complicated (aka stupid) design with 0 instruction....

[@joecox9958]

remove the useless music, add info like opening dimension etc thx