How to install CZ Sights to CZ Shadow 2.

[@rbdenham]

Really good video! I love the way you explain every step! I had been looking for a good video to show how to adjust the windage for the CZ Shadow 2 original sights, and this video is the best I could find even though you show how to remove the sight. I now have a great better idea of how to change the windage.

[@ΣΚΟΠΕΥΤΙΚΟΣΟΜΙΛΟΣΑΤΤΙΚΗΣ]

Really good video! I love the way you explain every step! the aluminum part that holds the shutter that we can supply;

[@ivanortiz7248]

thank you so much great video

[@markuszadra8225]

thanks!!!super!!!

[@jerryjohnsonii4181]

Thanks for the knowledge !!!!!!!!!!!!!

[@roberts6986]

Jakby kto z Polski oglądał to wszystkie piny wybijamy od prawej do lewej szczerbinkę też. I praktycznie jest zjechać szczerbinkę na papierze (dół) wtedy dostanie luzu, cały czas kontrolując jak wchodzi. Szczerbinka jest tańsza i łatwiej ją zastąpić.

[@Peterpuijk]

Strange, I know you have to remove rear sight from right to left, you did bang it the other way araound

[@dodonpaa10]

Looks so easy

[@AdamAlbright-u4l]

I'm running a Holosun optic on my S2. Am I able to remove the front site and just replace the pin to keep the barrel bushing in place? Or is the front site crucial to holding that barrel bushing in place?

[@VeryFastRodi]

What is the best way to change the rod itself, they sit quite deep in the sight so you can get just cut it and take it out My current one i had to take out, did get it out, but ended up damaging the sight slightly. Love the sight itself and works great, but changing that rod is a pain.

[@tbear6812]

So when you gently hit with the hammer to get the front sight loose you hit abit on the slide with the hammer at the same time! :D :D :D Well done!

[@rbdenham]

Is there an easy way to move the windage at the range to sight in the cz shadow 2. I feel like mine is off about 2 inches to the left at 25m. I have a Sig p320 legion, and it's spot on, so I don't think it's my aim. Any help on moving windage would be appreciated.

[@allexthebeast93]

Move the rear sight to the right...few taps..and will be ok!

[@rbdenham]

@@allexthebeast93 Thank you sir! I will try that!

[@motoriderguy3854]

My shadow 2 shot to the left as well ,I have two of them and they both shot to the left and it wasn’t my aim .

[@motoriderguy3854]

I put a tax sport 1.5 mm fiber rod on my shadow 2 and anyone that reads this should try it , it improved my groups by a bunch , it helps me line up the sights and is a tad wider to fill in the gaps a little more .

[@motoriderguy3854]

Tac sport that is .

[@christianlingner2225]

OMG! The Dovetail is on the right side smaller than on the left side. You have to push out the rearside from right to left and install from left to right.

[@purplearrow47]

Thank you so much.

[@jalermaling8736]

I'm hearing, rear sight removal from the right side, and installation from the left side. Anyone done this before to recommend?

[@harveycamacho2247]

Are shadow 2 the same as p01 sights

[@vicgerber9837]

What size is drill bit for front sight?

[@paulhagiantoniou530]

Hello Vic, it’s a 2mm bit

[@jalermaling8736]

@@paulhagiantoniou530 kindly, I already bought MEPRO Hyper-Bright tritium Night Sights set, and would like to know whether the drilling would still be necessary. By the way, is it preferable to use a Drill Driver or an Impact Driver?

[@paulhagiantoniou530]

@@jalermaling8736 Brother I don’t know the sight you have bought but definitely drill, not impact

[@jalermaling8736]

@@paulhagiantoniou530 Meprolight ,It's a company based in Israel. Check them out. I wanted tritium night sights for my shadow 2, and they happened to be the only one that had a direct compatible replacement.

[@purplearrow47]

Why on earth would you leave a video up that shows removing the rear sight in the wrong direction. Seriously, i use a lot of your products but you are going to damage shadows with these instructions.

[@paulhagiantoniou530]

It’s not a tapered cut

[@cubukluugur6777]

Kratzer, kratzer uhhhhh.😢