I literally got so frusrated trying to get a sporcket on strait without warping in the process that I numbered every bolt in a cross pattern like a cylinder head and made 1 turn and then switched to the next bolt. It took forever but worked great.
@charleneblack2792 Жыл бұрын
That's a great idea! Thank you!
@terranceturnbow818426 күн бұрын
Bro use zip ties place them around the hub between the sprocket to get a perfect alignment than when tightened pull them out
@sulaimanashraf182325 күн бұрын
@@terranceturnbow8184Elaborate
@Jazzy_Reacts3 жыл бұрын
I put one of these together and this is by far the most difficult part. I tried finding a pre assembled one but no luck
@MsAhlexusP3 жыл бұрын
You can put a shallow 1 and 1/16 1/2 socket. Put in the center or the sproket and depending on your axle. Most you can put the nut back on. And it will hold the sproket center. The entire time, and you wont have to adjust the sproket back in forth to get it centered out.
@rexterrocks6 жыл бұрын
Most kits now only come with one set of plates, usually one with 5 holes and one with 4. There isn't any need for the extra plates although I changed my sprocket recently and had spare plates and thought I would try 2 sets and it did seem easier to set up. One mistake he made that you should avoid is make sure the cut in the ring is UNDER a plate and not between them. A good way to tighten the bolts evenly is to use a ruler or piece of card and mark how much thread is showing through on it and do them all the same. The 10mm nuts are very easy to strip if you overtighten them.
@timothyaldrich41273 жыл бұрын
My bike came with only 2 plates and unlocks what a pain been trying last 2 days on and off hopefully I'll get it this is a 2 man job definitely
@rexterrocks3 жыл бұрын
@@timothyaldrich4127 I'm just fitting a new sprocket myself. It is hard to line up. I fit the plates, rubber and sprockets on as near as I can get, but not too tight, then, with my bike upside down I remove the front wheel and put the rear one in its place. I can then spin it and see where to adjust. It makes it a lot easier.
@dustinh4175 Жыл бұрын
I replaced the factory sprocket bolts with allen bolts from an old motor and make sure to use a flat washer on the outside of the sprocket and then on the inside I use a flat washer then a lock washer then a regular nut but longer with more threads then double nutted to a nylock nut and it holds good and looks cool too.
@charleneblack2792 Жыл бұрын
Getting this sprocket straight is nearly impossible. I've been fighting with it for hours. I've never done anything like this, so that makes it harder. Good luck, everyone!
@brandonkellogg95904 жыл бұрын
If the coaster brakes doesn't clear the bolts, switch to button head bolts. They are much lower profile.
@MeiGunner2 жыл бұрын
You can also face the sprocket in or out to make sure the chain stays straight with the motor
@DavidWilliams-dz7zd Жыл бұрын
Would you guys be able to install a sprock on a rim and then sell it to us if so I want to buy one that has one already installed
@Killasandwick9 ай бұрын
As soon as he said don't accidentally completely disassemble the entire axel is where it's went wrong. Goddam!
@ambroseabellair53065 жыл бұрын
Your putting the plates in the back of the sprocket and behind the spokes but you didn't mention that. You made it sound as if there were just plates on the inside of the wheel hub, but unless I'm seeing things you have another set of plates between the sprocket and the outside of the wheel against the spoke. Is that for pushing the sprocket out further for clearance or do you need it for securing the sprocket to the spokes. Never saw that before, wondering why, just saying it cause's a little confusion when you do something but don't actually mention it, just a little slight of hand hey partner.
@413MassDigger3 жыл бұрын
i said the same thing,, never seen plates behind the sprocket like that before
@audieallen97342 жыл бұрын
my kit came with a butt load of extra lock washers and regular washers, and I can't tell how many I should use? should I put a lock washer and regular washer on both sides, if I have enough?
@alangoodrich65904 ай бұрын
Same
@MeiGunner2 жыл бұрын
You only need 3 brackets not 6 if you took the ones off the back of the sprocket and threw away those 3 extra you'd be able to fit the coaster brake back on
@dustinh4175 Жыл бұрын
I feel like the 3 bolt plates are better, they dont bend as easily. Better steel or something but thats just my personal experience.
@jerrydahms2084 Жыл бұрын
if your having a problem getting the sprocket straight use some zip ties between the dust cover and the sprocket.. might have to trim down the dust cover if your not wanting to use zip ties. any other ideas would be helpful. Just a few I've done so far as a newbie.
@bobjohnson95972 жыл бұрын
when showing initial set up you show the outer edge of sprocket closer to inside of wheel however when you actually mounted the sprocket the outer toothed edge is away from the center of the sprocket which changes the alignment of the chain in referrence to the front engine sprocket. Which side of the sprocket should face out?
@charleneblack2792 Жыл бұрын
I'm curious, also. I think I'm going to flip mine around, so the teeth are closer to the wheel.
@SteveMayle9 күн бұрын
What's wrong when after installing the sprocket and the opposite spoket for the bicycle chain no longer moves freely without spinning the coaster break?
@hirockn Жыл бұрын
Please tell me the size of the chain on the engine side.
@kxlucifer8 жыл бұрын
just get the hub adapter assembly theyre better thicker material and doesnt require bending the coaster brake arm since the bolt sit flush..source i have 2 motorize bikes both have them.
@abumannocchi80486 жыл бұрын
K Lucifer I have a ten speed the motor 80 chain hits the bike frame ,what should I do? And if anyone knows where to get replacement engine mount bolts let me know.
@martinj96476 жыл бұрын
Probably because there is pretty much an endless variety of hub diameters while there is only maybe 3 different sized hub adapters, so unless you do some wonky business with shims, or have your own mill they won't fit many wheels, and buying a new wheelset and $30 adapter to save 15 minutes isn't feasible for most people that are building a motorized bike as an inexpensive alternate mode of transportation
@dexlofi Жыл бұрын
My problem currently is that my rear coaster hub is too wide in diameter to even fit the sprocket.
@josh76372 жыл бұрын
Tightened the bolts down pretty meticulously with even pressure. Center of the sprocket is center with the hub beautifully. Wheel is back on the bike and turning the pedals by hand, I notice the rear sprocket has tons of wobble as it goes around. Should I go around and snug bolts accordingly again? It's bad enough that it will need to be corrected. Just didn't know if there were any tricks I should know about.
@dominicmancini8330 Жыл бұрын
Put something ther to keep it centered. Hope helped
@naumansm34 жыл бұрын
How much should the bolts be tightened ? For me, the tire seems to be have gotten a 'wobble' after I tightened the bolts
@malleusmaleficarum60042 жыл бұрын
You likely did over tightened some of the bolts, but the main problem is that you tightened them unevenly and put more pressure on certain spokes pulling the rim out of alignment
@Mac18124 күн бұрын
My set only came with 3 pieces think that’s going to matter ??
@D347H27 жыл бұрын
I need to know how you get the sprocket to stay straight. no matter what Ive tried, my sprocket seems to go off of alignment even just the slightest and it does cause a HUGE problem with the chain going too tight and then loose because of the bobbing of the sprocket. I've tried so many times to keep it aligned and it just goes off the slightest.
@D347H24 жыл бұрын
My solution to this was getting a hub mounted sprocket. I unfortunately stopped building motorbikes over a year ago. I was building them and selling them for decent money. But check out BBR Hub mounted sprockets or look them up on Amazon. make sure you use a digital caliper if you don't know how big your hub is on your rear wheel. Make sure you order the right size if you go this route. Believe me, i will NEVER use a spoke mounted sprocket ever again.
@brsproductions61173 жыл бұрын
Are you tightening the bolts properly? Does it become misaligned immediately, during the first ride, or after a few rides? U may need to install ride then retorque after 10 or so minutes of riding. Edit: you should be making sure all bolts are tight before each ride. The shaking from the motor will loosen bolts and screws due to vibrations.
@joelstrickland88902 жыл бұрын
@@D347H2 do you know if this kit will Work on a 3 wheel schwinn meridian?
@D347H22 жыл бұрын
@@joelstrickland8890 I really dont know as I've never built a 3 wheeler. I haven't built a bike in many years due to working a lot
@joelstrickland88902 жыл бұрын
@@D347H2 ok thank you for the reply, have a good weekend.
@skilletfingerz7380 Жыл бұрын
What if the bolts don’t go through the spokes can you mount it somehow else with adhesive or some sort of other bolt can’t get another bike and tbis is the only option
@jynkot55423 жыл бұрын
thank you im in the process of building one just ran into a problem with bent rims that is throwing the sprocket off alignment
@deborahwebb90123 жыл бұрын
What if I put the spocket on back wards, do I really have to turn it around?
@motoredbikemadness20613 жыл бұрын
If your chain isn’t rubbing the frame and is aligned straight with the motor then it’s fine
@ventus_luxis Жыл бұрын
but how do i get the support loose from a brand new rim
@austinshipley04 жыл бұрын
THANK YOU SO MUCH EVERY OTHER VIDEO ON HOW TO PUT IT ALL TOGETHER SKIPS THIS PART LIKE ITS IMPORTANT!!!
@jduboi510 жыл бұрын
i just realized that my bike has 29in wheels, is it possible to install it on this size cause im running into problems!!
@martinj96476 жыл бұрын
Wheel size doesn't matter so much as spoke count and pattern. The holes in the sprocket are basically only made to fit a set number of spokes, any more than that and it's impossible to line up all 9 holes without bending spokes or changing the lacing pattern. Edit: the optimal seems to be 32-36 spokes for anything 24-29", though there's undoubtedly other combinations of wheel size, spoke count and lacing patterns that'd work. On my bike I have 29" 48 spoke wheels, so every 3rd hole is blocked, so it has 2 bolts, empty hole, 2 bolts, empty, etc.. If you need to do this just make sure none of the side by side bolts are in the same plate on the back(each middle hole of the plates should be empty), and the cut in the rubber piece is behind on of the plates, not where two meet. Of course it's ideal to have all 9 bolts in but I've had this bike going on a year and just removed the sprocket to change out the spoke nipples and there were no bends or other visible signs having the 3 bolts out was causing any issues
@compunerd6 жыл бұрын
i bought the upgraded clamp that goes right on the hub..s o much better
@darioontiveros40845 жыл бұрын
What happens if you do accidentally disassemble the axle. Then what?
@nathanael5606 Жыл бұрын
You will have to learn how a coaster brake works, and then put it back together with grease.
@cobzoid1883 Жыл бұрын
reassemble it lol
@cobzoid1883 Жыл бұрын
i didnt the same thing you just have to screw it back in with all the bearings in place
@Eetu-vu6yc3 жыл бұрын
I have 26 wheel but it has 3 gears so the middle ìs bigger i cant fit the sprocket on any tips?
@brsproductions61173 жыл бұрын
How to set the pre load or whatever for the bearing
@panzerwolf4945 жыл бұрын
Yeah, don't use these clamps, they fuck your spokes up just from the engine starts. Get yourself either one of the wheels with a hub drilled for a sprocket, or one of those clamps that bolts around the hub.
@alexonwheels41902 жыл бұрын
What should I do if my wheel only had 32 teeth but the sprocket has 9 holes?
@lyntiecegalleher31102 жыл бұрын
How to put together the rear axle together
@jeremiahsanchez10948 жыл бұрын
Why is this still posted if you no longer have them assembled like this? Or why not make an updated video?
@robbiemclendon10473 жыл бұрын
Mine only came w/the 2 backing plates..already been thru a set of bolts trying to get it together, won't tighten evenly...
@Sophia-hs3rz7 жыл бұрын
Hi, like your videos. I see some using a flat sprocket & you're using a dish. What are the different applications?
@dominicmancini8330 Жыл бұрын
Is it the spokes that holds the sprocket in place
@pablodalisay7132 Жыл бұрын
Is there a sprocket for engine with free wheeling?
@cooperk021343 жыл бұрын
Question, does it matter what side of the sprocket is either inside or out? It looks like I can mount it with the teeth more on the inside, then if I flip it they will be a little more towards the outside….
@coltonrooster3 жыл бұрын
As long as it's aligned doesn't matter
@sompophuayrahan38913 жыл бұрын
Can i just use the fixie gear it self...(the both fixie and single speed bike)
@worscohliАй бұрын
ummm i dont think mine has plates on both sides of the pads
@0spike4 жыл бұрын
Hi great video, can you tell me what bike your using?
@MaverickNelson39 жыл бұрын
I do the same as this vid and I have problems while test riding it. I take the coster break off and install the sprocket and reinstall the coster break, but when I ride it wthout the motor chain on and use the coster break the rear hub untightens and makes my rim Loose. If anybody knows could they please tell me why it does that. It already broke 2 rims from it unloosening.
@TheTechnology199810 жыл бұрын
Does the new sprocket fit the bicycle's chain or is the sprocket to big? Plz respond back.
@b1200guy5 жыл бұрын
No, the new sprocket fits the chain that comes with the kit, a 415 size motocross chain. You have to get these at a motorcycle store if you need to replace it.
@jordonfoster52806 жыл бұрын
What if I have rear disk brakes
@bikeberry6 жыл бұрын
Most standard disk brakes will need to be uninstalled before the rear crank assembly can be installed. There are aftermarket extension brackets and larger diameter disk rotor which can make the use of disk brakes possible.
@miguelhuertas77695 жыл бұрын
Hi the sprocket teeth go to outside or inside thank you
@truongameo88213 жыл бұрын
Friend did ít good me looking and how made it same same you
@mitchnolan70053 жыл бұрын
Put tape on the bolts to hold them in place
@underworldslums63138 жыл бұрын
my motor sprocket has a slight wave in it causing the chain to keep slipping off of it. I've readjusted it a few times and switched out a new one and still has that wave in it. any tips?
@taitheguy858 жыл бұрын
Yes: remove sprocket, flip it over, reinstall. If that doesn't fix it, then ur chain tensioner is ur problem. I would recommend a sprocket chain tensioner (like 30 bucks on eBay).
@curtisanderson34278 жыл бұрын
if the two gromet pieces are in bad condition could this affect the centering of the sprocket?
@wildbill23c6 жыл бұрын
Yes, it will throw off the center of the sprocket, as well as not tighten down properly and cause an off-balance issue...more so than normal.
@tjdukes745210 жыл бұрын
Can someone plz tell me wat i can do about my rear wheel ....the bearings just keep getting destroyed fast wat kind of bearings can i put in it to make it last ot where can i get a heavy duty rear wheel with heavy duty bearings
@STT.40 Жыл бұрын
I read that you need to use heavy duty automobile grease in the hubs and bearings. The regular bike grease is not durable enough.
@emeryseyller802910 жыл бұрын
for some reason my bike kit did not come with the two other plates ( 4 hole and 5 hole ones) i tried installing it without them for HOURS... wheel doesn't spin right, crooked, all sorts of problems... what do i do now? i am extremely confused
@soccermessi-dq2eo7 жыл бұрын
Hey I just received my kit today and it did not come with the other 2 plates either, what did you do?
@mariesayegh6646 жыл бұрын
Same
@theone2be336 жыл бұрын
Call the manufacturer and get your missing parts or report them to the Better Business Bureau
@psytastic22156 жыл бұрын
I got those but I didn't get the sprocket I'm pretty pissed off
@patherrada48768 жыл бұрын
I have not purchased a engine kit yet I'm just doing some research be for I buy and I noticed that the video says to use a 26in wheel with 36 spokes and my bike has 52 spokes and is 29in wheel I was wondering if would run into any problems putting on the sprocket.
@paramandans8 жыл бұрын
Don't use those, it will mess up your wheel. Get the after market sprocket adapter.
@kxlucifer8 жыл бұрын
pat herrada itll be fine it just wear the clutch faster with bigger wheels
@MeiGunner2 жыл бұрын
4:07 Oof that's sprocket is crooked you said Tightening and align the bolts evenly ... ( Get that wibb-al woBb-al out of there and you have less vibration on your rides out on the road)
@MrGuidoeric9 жыл бұрын
I am not finding the video for grinding the sprocket teeth
@tsvetomiriliev58047 жыл бұрын
What about the rear disk break?
@pablodalisay88112 жыл бұрын
Is there a free wheeling on the sprocket for engine ?
@Killasandwick9 ай бұрын
You overtightened the coaster hub which is on the little sprocket side of wheel. It should be hand tight to free wheel.
@fuelityourself10 жыл бұрын
Have the kits always s had the double washer plate set?
@joshuawalker25733 жыл бұрын
Mine only came with 1
@devinpratt95429 жыл бұрын
my coaster brake is really hard to get off. any suggestions or videos to remove it?
@taitheguy858 жыл бұрын
Two 4-way tire irons (or a torque wrench)
@beancube20109 жыл бұрын
Why don't we have some universal motorized front wheel bicycle kits that can just haul any regular bike without making change to the rear part of the bike?!!
@abundantsound77755 жыл бұрын
There is. Just google bumblebee motorized bicycle front wheel kit. Done.
@aaronsteiding45684 жыл бұрын
After hours and hours of trying to get the rear sprocket aligned (which it never did), save yourself the headache and get a sprocket adaptor. Trash the one that came with the kit.
@husnainemd63227 жыл бұрын
where to buy that I don't know can you tell me please in india
@ethereine60584 жыл бұрын
Look up 2 stroke engines for motorized bikes
@themiddleman73222 жыл бұрын
Super simple and clean 👌👌👌
@CreativeM358 жыл бұрын
When i try to remove the brake coster the whole thing comes of with it. not just the arm, how do i overcome this obstacle?
@taitheguy858 жыл бұрын
Some are tightened to the nut MUCH tighter than others. Took me a while to figure out also, but in the worst cases (like urs) u either need a toque wrench, or two 4-way tire irons. Use one tire iron on the nut, & the other on the coaster brake arm itself. Hold the brake arm down (or up) while turning the nut counter clockwise
@BadAls199 жыл бұрын
14 if you were to use the 14 gauge spokes are they going to snap or are the thicker ones just a recommendation
@StilwellMotovlogger8 жыл бұрын
It's possible they will break, or your sprocket will get bent. In my opinion it's a necessity not a recommendation.
@_ken62437 жыл бұрын
do the motor schwinn meridian motofized mooried cmeaa listien soften.
@wildbill23c6 жыл бұрын
Using heavier gauge spokes is just a gimmick to get you to buy their more expensive wheels. If you install the sprocket and adapter properly it will work just fine with 14 gauge spokes. The bigger problem is keeping the engine mounted on the bike. I've broke 2 motor mounting studs in less than a year. These engines need far heavier grade studs than the cheap ones they provide and sell as replacements. I'm going to find out what size they are and go get my own heavier duty ones.
@bennyvazquez12137 жыл бұрын
my bike has aluminium magna weels purchase in wallmart how do i install the sprocket on it can any one help me out
@tmabjj19 жыл бұрын
Would it still fit on 700c size wheel like on a road bike
@theone2be336 жыл бұрын
Maybe
@Maku_1009 ай бұрын
Thank you wery mutch.This was helpful and keep going in theese videos
@johnfarnham26148 жыл бұрын
What is the name of this or part number??
@KN4YEM8 жыл бұрын
Thanks alot for this video I will be doing this soon.
@integrationofmanandmachine47145 жыл бұрын
How is it now
@dronescheck39913 жыл бұрын
I only have 3 metal plates
@anthanyjohnson63806 жыл бұрын
Do we need to take dust cover off
@bikeberry6 жыл бұрын
Typically, it is necessary for proper clearance, but there are some wheel sets which can have adequate clearance with the dust cover on.
@mariodiodato3096 жыл бұрын
Anthany Johnson scusa come va montata la corona
@psytastic22156 жыл бұрын
I never got the sprocket for my kit I bought is there a cheap way to get one??? All the ones I see are like $50
@bikeberry6 жыл бұрын
If your kit came without a part give us a call and we will send it out to you. (800)317-0479
@clerissonmesquita2 жыл бұрын
Thank you so much for your invaluable information, highly appreciate it, keep it up the outstanding job, have a great day.
@F14TOMCATFT9 жыл бұрын
Thank you very much this video did help me
@BadAls199 жыл бұрын
Where can you buy this part individually???
@davidcoon36024 жыл бұрын
Bikeberry.com
@richards98657 жыл бұрын
Very nicely done - thanks.
@The13thGuest8 жыл бұрын
Will it fit on a high flange hub?
@integrationofmanandmachine47145 жыл бұрын
Parachute regiment
@evoemperor37768 жыл бұрын
how many tooth is the sprocket? what chain is used 415?
@integrationofmanandmachine47145 жыл бұрын
Yesh
@Oldcoinsandstuff19 жыл бұрын
If you have a mountain bike why can't you just use the sprockets that are already there instead of adding a new one on the left side? They make engines that turn CW with the crank on the right.
@taitheguy858 жыл бұрын
Cuz the drive chain is always on the left of the engine. & if u can't pedal the bike, then it's not technically a bicycle, & u would need license & registration on public roads... Well, if u get caught that is
@anwezzyupt2028 жыл бұрын
you should do a video of how to change the tire.
@mattmesi Жыл бұрын
They gave me split washers But I don’t see any being used for this video So I won’t use them. I have the exact same bike
@ericmccormac61025 жыл бұрын
I watched this twice. What motor?
@ericmccormac61025 жыл бұрын
newb problem.. byoe haha :)
@BobTheBuilder2942 жыл бұрын
every time i destroy a wheel i get a cheap used one for like 5 bucks and i mess up the sprocket installation. Looks like mine is 14 gauge and i'll be destroying it again, oops.
@mikehasuga4959 Жыл бұрын
Well done
@chucklehead36977 жыл бұрын
you said to leave a comment if you left anything out
@0Kizzy7 жыл бұрын
Im having issues with ths sprocket not fitting the rim it looks like i have to machine it out about 1/8th inch for it to work
@maddenmadness8 жыл бұрын
what size is the sprocket
@scaw-j9 жыл бұрын
Hi there, I am trying this installation but I have 29" wheels and the 9 holes don't line up with the spokes. Do you have any advice for me or am I completely screwed? Thanks.
@TIMEtoRIDE9008 жыл бұрын
+Scaw drill baby drill !!
@taitheguy858 жыл бұрын
Just use a wheel with a different spoke pattern. Size doesn't matter, spoke count is the issue. P.s. don't "drill baby".
@martinbyrne66434 жыл бұрын
The sprocket u fitted is no running concentric ‘ u need to re do it ‘ sorry
@ashribadbiswal66806 жыл бұрын
How can bay online
@bikeberry6 жыл бұрын
bikeberry.com
@zoologicalmilitia22419 жыл бұрын
why is my chain jaming forward my clutch is off the chain jams
@stevenwatson82954 жыл бұрын
A real headache 😣
@sberg84749 жыл бұрын
Nah, who need brakes!
@cordariousriggins97088 жыл бұрын
bro my bearing just fell out when i got off the bike do need to buy a new rim
@stevenwatson82954 жыл бұрын
Take it to a bike shop. I'm 3 years late. 😂
@paramandans8 жыл бұрын
Don't use those they will jack up your wheel and bike.
@BlazeWells-ok3ei2 ай бұрын
😮😅I have no brakes
@fuze_perronplayz36375 жыл бұрын
I love how they just ripped this out of there entire bike vid and then made an entire new vid on it
@Employee9414 жыл бұрын
FuZe_Perron Playz yup
@Killasandwick9 ай бұрын
And the sprocket doesn't fit over the dust cover until you shave the hell out of the inside of the sprocket