How To Install the «Magic Door» System

[@ahmedradwan9127]

can i know the maximum length that door can open ? can it cover 120 cm opening with 130cm door slap ?

[@doordesignlab]

Hi, opening should be 4 2/16" - 2 3/16" smaller then the door slab. So, yes, 130 cm wide slab will be enough to cover 120 cm opening.

[@BoRis-km2fb]

is it possible to mount the wall hardware beside door opening not above like in the tutorial? In case of a room-height door ( door opening from floor to ceiling )

[@doordesignlab]

In this case you will need different door hardware, probably some kind of sliding system.

[@LEMIANGEL]

Why not showing the door totally open?

[@MrJaimepayes]

it doesn't open up all the way due to the mechanism.

[@caryldizonsusatijo7623]

Hello, would the Magic 2 system work for a solid door that is 1 1/2" thick and 50" wide. It's a custom door that weighs around 200lbs. Thank you.

[@doordesignlab]

Hi, probably not

[@dominickgabres614]

Where to buy those rollers, guide/tracks, etc. used in this door?

[@doordesignlab]

Come visit our our site doordesignlab.com/

[@NinjagoBattles00]

Where did you get this door from? I love this tutorial, but I'm having a hard time finding door slabs large enough without a pre-drilled hole for a handle

[@doordesignlab]

Hi, you can browse a selection of our doors on our website: doordesignlab.com/

[@benjaminsnoize]

Center in opening I'm guessing

[@murielbuhr8451]

How did you get the grooves in the bottom of the door slab?

[@doordesignlab]

We do all necessary precuts on our factor using special equipment

[@richardlea818]

If you were modifying a door on the job site, you’d have to use a router. Not impossible, but slow.

[@cghrios783]

@@doordesignlabdo you sell the doors too? Thanks

[@jeffreyg.capacite6165]

where to buy this mechanism?

[@doordesignlab]

Hi, please visit our site: doordesignlab.com/magic-1800-concealed-sliding-system-for-wood-door.html

[@petek8716]

Very nice !

[@doordesignlab]

Thank you very much!

[@shred46]

Almost a great design. I see issues with the roller wheels at the bottom of the door. Dirt accumulation, carpeting, wear and tear on wooden floors. The traditional pocket doors or wall mounted sliding doors with the rollers and soft close, soft open mechanism located at the top of the door are a much better design. Function over design vs design over function

[@doordesignlab]

Thanks for sharing!

[@christianmorat2266]

Bonjour ou trouver ce matériel non du fournisseur adresse s'il vous plaît merci

[@doordesignlab]

Please, contact us via contacts on vrcbaltic.com/

[@tonynotaro4607]

Min 2:30....wrong wheels installation

[@carloco41]

En español x favor y si las ay en Madrid españa

[@doordesignlab]

Please, contact us via contacts on vrcbaltic.com/

[@DedeSalimah-x1c]

Uing butuh rel model Kitu dimana meulina

[@belldinnidoors]

Rail sold only together with the mechanism

[@murielbuhr8451]

How do you do the millwork in your doors to allow hardware attachment?

[@doordesignlab]

We do all necessary precuts on our factor using special equipment

[@brownbear4360]

where can i buy magic door hardware and plastic guide？

[@lel4866]

Yes l would like the same information

[@doordesignlab]

Hi, you can find them on our website: doordesignlab.com/

[@LeslieMcDaniel-m6q]

The directions and the service rep I talked to were NO help. No where on the site or pre order information does it state you need to have the door 7-10" wider than the opening - and the header 3" shorter.

[@doordesignlab]

In order to assist you better, we kindly ask you to provide us with additional details about your specific situation. This information will help us to give you more precise instructions and assistance. Please be assured that our team is committed to helping you resolve this issue as quickly and efficiently as possible. You can contact us at doordesignlab.com/ or respond to this comment with any additional information or questions you may have.

[@brianmanne7493]

Gy’Odd, What a convoluted and poorly filmed video!

[@doordesignlab]

Thanks for your feedback, we'll take it into consideration in our next videos.