How to Install the Minn Kota Ultrex QUEST Trolling Motor

In this informative video tutorial, Andy Kratochvil of Fish Lectronics (www.rigmyboat.com/) unveils and installs the new Minn Kota Ultrex QUEST trolling motor. This video is a must-watch if you're interested in installing the trolling motor yourself and saving some money. Kratochvil delivers a thorough guide to unboxing, understanding the components, and installing this top-tier trolling motor. Check out our detailed Minn Kota Ultrex QUEST Overview ( • Minn Kota Ultrex QUEST... ) video to lure the full scope of features and capabilities of this motor.
FEATURED MARINE ELECTRONICS
• TROLLING MOTOR - Minn Kota Ultrex QUEST. Learn more about the Minn Kota QUEST Series trolling motor www.wired2fish.com/fishing-vi...
• CIRCUIT BREAKER - Minn Kota Circuit Breaker / MKR-27: Buy at Amazon www.amazon.com/Minn-Kota-1865...
• TROLLING MOTOR PLUG - MKR-28 Trolling Motor Plug and Receptacle: Buy at Amazon www.amazon.com/Minn-Kota-1865...
Kratochvil starts by unpacking the box, revealing the contents, and explaining the significance of each item. From the owner's manuals to the recommended MKR-27 circuit breaker, he covers it all. He also lists all the tools and supplies needed for the job.
Next, Kratochvil leads us through the Minn Kota Ultrex QUEST installation process, where he sets up the mono-arm on the deck and details the attachment process for the steering housing. He then demonstrates how to secure the motor to the boat and identifies the tools and components used, such as the Fasteners, Fender washers, Nylock washers, and anti-seize. He delivers many practical tips that only a seasoned rigger can.
Kratochvil walks us through the next steps in the process, which include attaching the lift assist springs and installing the prop. He also outlines the installation of the bow mount stabilizing arm for optimal motor stabilization.
Finally, he addresses the different cords and accessories that come with the Minn Kota Ultrex QUEST trolling motor. These include the micro remote, the i-link connector for compatibility with Hummingbird head units, and the sonar extension cord.
Remember to follow all installation instructions carefully for the best results. And as with any installation, make sure to reference the included installation manual. With Kratochvil's step-by-step guidance, installing the Minn Kota Ultrex QUEST trolling motor can be a straightforward and cost-saving project.
► SUBSCRIBE for more AWESOME FISHING TIPS: wired2.fish/YTSub
FOLLOW US HERE:
► www.wired2fish.com
► / wired2fish_official
► / wired2fish
► / wired2fish

[@johnmcgahan4696]

Excellent excellent excellent video. I just got my Quest and will be ugrading from the Ultrex. This will make the install so much easier. Thank you!!!

[@Wired2Fish]

Good luck!

[@PerryShriver]

awesome stuff. 👍

[@camilrykowski5765]

Great vid! How important is the anti seize compound? I forgot to use it on my quick release mounting plate, and prop nut. Thanks

[@kenbrown5449]

I watched your video on the installation of the Ultrex a few years back... Helped me out a lot! I'll be referring to this one in the future when I upgrade. I have the Minn Kota Quick Release Bracket installed.. Will it match up with that? Thanks for the great video!

[@Wired2Fish]

Hi Ken, thanks for the note. The hole pattern for the Ultrex QUEST is the same as the 1st gen Ultrex but you'll need to bore the mounting holes out a bit bigger to account for the thicker stainless mounting hardware. Andy covers down on this difference in the video.

[@Gumby905]

Will my fortrex 24 volt plug be ok to reuse like he did in the video. My pro V bass had the 36volt plug upgrade but i only use 24 and not sure what plug the dealer put on the fortrex but looks the same

[@Go-hogs]

Has anyone ran into the mountain not releasing to fold up to access the holes to mount?

[@kayakfishingforpredators9107]

Good to see the safety aspects . ALWAYS USE CIRCUIT BREAKERS (Fuses). Its very important also use a good fuse holder and ALL the components in the electrical circuit are rated for the High Currents when the motor is in use. Last but not least: Keep out Any Moisture from the Fuse block 😁⚠️

[@Wired2Fish]

Thanks for sharing

[@chestophercolumbo4561]

Would love to see a power pole Move vs this new Minn Kota

[@wickedbassn]

Give it time. I'm sure Russell marine will make one.

[@axkicking]

Installed my new Ultrex Quest. Spot lock , programmable button, right side stow, and turn strait when deployed doesn’t work. All turned on with the app

[@Hoots_Golf]

On the normal ultrex if you don’t have graphs do you need the heading senser

[@Wired2Fish]

Adding a heading sensor still adds functionality without a Humminbird Fish Finder. The functionality is related to the Spot-Lock Jog feature, which may not be relevant to you. Per the HB product page: This Bluetooth-enabled heading sensor contains a compass that detects your boat's heading and communicates it to your trolling motor to enable the Spot-Lock Jog feature, which lets you move your Spot-Lock location in 5 ft. increments in any direction.

[@seananderson1578]

Need to bring my new boat to you

[@Wired2Fish]

He's pretty good at what he does!

[@robertprice7725]

If you are replacing the older Ultrex with the Quest do the mounting holes line up or do you have to drill new ones

[@axkicking]

Mine lined up. Just need to drill larger. Quest bolts a little larger

[@jtb2180]

Was the quest lighter or heavier than the ultrex ?

[@user-lm9dg5qv8l]

~7 heavier

[@denniswilliams3418]

Do the holes match up if you have an ultrex?

[@Wired2Fish]

good question, yes they do. You just need to bore out the original holes a bit bigger with the drill bit size specified in the vid.

[@ajzombieboy1384]

does anyone know the official release date of the ultrex quest?

[@denniswilliams3418]

Tackle Warehouse says in stock Dec. 1st

[@Wired2Fish]

Yes, we were informed that the Ultrex QUEST is shipping to many marine dealers on July 1st, so those businesses would be a good starting point. Ulterra and Terrova is slated to ship later this summer.