Showing the function, wire connect, setting and speed sensor connecting
Пікірлер: 52
@donaldstephens60012 жыл бұрын
Like your video I was wanting to see it from start to finish but I think you put enough info for me to figure it out on my end ty youngen
@quieromicubita Жыл бұрын
So glad I found this video. I thought I would be able to configure with the manual... I was so wrong
@aljoforeveryoungatheart7934 Жыл бұрын
Excellent explanation. Worked right out the box. The wiring colors matched this video. Just wonder how to stop the tank gauge from flashing as I have no sending unit in the tank. Maybe use a resistor (between 32 and 566 Ohm) between the Blue/White wire and ground. Any comments are great - just have to experiment with that.
@CantTreadOnMe11 ай бұрын
Have you figured it out?
@billridley7130 Жыл бұрын
Very practical and helpful, not full of bull like some, excellent
@hre2motorltd178 Жыл бұрын
thank you
@thetoymaker94043 ай бұрын
@@hre2motorltd178 if you use the roundy sensor number 2 that aliexpress sells without magnets what setting must be entered on gauge?
@Davidbirdy-si9vm3 ай бұрын
Speedo seems to be a dodgy one for me I've set distance and amount of magnets, it's wired up. Anything else I should be looking out for/common mistakes? Never seen one of these had no instructions wired it up with a multimeter as oem dash was also missing. Ty for all tips if you have any for me 👍👍
@attilacseh340627 күн бұрын
How you do the magnet / sensor if you don't have rotor? What brand is this one? On Amazon like 4 different brand looks a same..
@hobonickel8405 ай бұрын
one sweet as tach... think this is doable on tw200? thanks
@evertonianluke2364Ай бұрын
Is there a wiring diagram from this what colour wires are for what part of the clocks
@anikitwoeight76233 ай бұрын
Is this working good still after all the time you have owned it?
@robertcasanova1316 Жыл бұрын
How do you adjust the speed
@bogdanittot73242 жыл бұрын
Great movie Do you know if it is possible to program initial odo mileage? If my bike has 25k Miles, is it possible on this speedo to program initially 25k on display?
@hre2motorltd178 Жыл бұрын
currently it is unavailable to set the initial mileage
@jamesratcliffe2127 Жыл бұрын
Hey mate I have installed this just having one problem when I accelerate fuel lvl going to empty flashing any ideas??
@thebruise Жыл бұрын
Great video, will help heaps, guess when the permanent 12v is disconnected the wheel dia and other info will have to be re entered? Cheers Rich
@brandonl1052 Жыл бұрын
If you haven't figured it out by now, the constant power wire powers the memory. Unplugging seems to reset all settings
@donaldstephens60012 жыл бұрын
Majority of bikes on average have 5 gears so the make it to fit the major variety of the majority
@David_loves_foods Жыл бұрын
What is the ppr of the honda ruckus?
@guard961Ай бұрын
how do i use the tyre circumeference mode?
@zachzat1581Ай бұрын
How do you get the gas gauge to work when your gas sensor has 2 wires ?
@MOAONAABE6 ай бұрын
hi, what is the small light on the end of the speed sensor cable for at the wheel end
@ThomasThrane-jd7se4 ай бұрын
Where du u get 1360 from? In menu 1???
@Pootus21 Жыл бұрын
How far from center did you mount the magnet? Trying to figure out how to set the speed but mine is way off. Did you use 2 magnets or just one?
@hre2motorltd178 Жыл бұрын
2-3mm gap between the sensor and the magnet, we usually use 2 magnets.
@TheWasch242 жыл бұрын
Are you using the stock fuel float or the one from a Met ?
@hre2motorltd178 Жыл бұрын
Any fuel sensor will work as long as the resistance is matched, you need to adjust the resistance from 32-566 Ω
@jakespeed94199 ай бұрын
I cannot get the tach to work no matter what i do, im running signal to black abd yellow wire from cdi box, negative ans positive are correct
@TheWasch242 жыл бұрын
Are you using the stock fuel sensor or the one from a Met ?
@hre2motorltd178 Жыл бұрын
Any fuel sensor will work as long as the resistance is matched, you need to adjust the resistance from 32-566 Ω
@humaharoon14862 жыл бұрын
I cannot switch between menus
@macteptm6 ай бұрын
Hello! I need your help! I have an MMB speedometer with digital display for the kilometers ,to my harley 79 and i have a serious problem.I start the ride if i push the button to reset trip 1 or trip 2 when i turn the bike off and start again the speedometer loses all the measurements!!!!! Today i started with 6.642 klm and after i reset trip at the gas station i had 7531 klm when i reached home.It loses the measurements when i push the button.I cant understand if its a wiring problem or the speedometer is faulty
@Dokterfuse_5 ай бұрын
Hey, its probably cause you dont have a wire straight from the battery + connected to the meter, this is needed to store the data even when ignition key is turned off
@heathercopeland4732 жыл бұрын
How did you hook up the odometer?
@hre2motorltd178 Жыл бұрын
please just follow the manual
@colin55mckay Жыл бұрын
Anybody have an issue with adding magnets and the odometer not saving ?
@MaNNeRz912 жыл бұрын
Isn't the rpm setting for 2 or 4 stroke? Not the cylinder number?
@dylew0893 Жыл бұрын
Yes
@brandonl1052 Жыл бұрын
I assume the way it works is it recognizes the spark signal as 1 revolution since its a 4 stroke engine(ignition timing). Setting it to 2 stroke just halves the count.
@revanreitinger18282 жыл бұрын
Can you please post a wiring diagram?
@hre2motorltd178 Жыл бұрын
Hi, we have updated the instruction, these will be more detailed,www.amazon.ca/gp/product/B07WW3L3Y8