How To Install The Rocker Box Assembly On A Harley Davidson Sportster

  Рет қаралды 118,382

HAMMER PERFORMANCE

HAMMER PERFORMANCE

Күн бұрын

A detailed video on how to install the rocker boxes on a Harley Davidson Sportster/Buell.

Пікірлер: 123
@cheff8383
@cheff8383 4 жыл бұрын
He is an excellent teacher. After I watch his video I could tackle any of these jobs with ease.
@gregoryranlett7868
@gregoryranlett7868 4 жыл бұрын
Thanks Dan, excellent presentation! I found your discussion regarding the breather flapper and rotating rocker-arm shafts particularly useful. Greg R., Boise, Idaho
@XenaTheQuadCamBikah
@XenaTheQuadCamBikah 3 жыл бұрын
Great videos Dan! These videos and the info on the Hammer website is extremely valuable to all of us installing our own kits. My 04 Sportster factory manual says 18-22 ft lbs on those four big bolts on the rocker boxes. I set the wrench to 20.
@bigroryhollar5023
@bigroryhollar5023 4 жыл бұрын
I would like to thank you 🍻not knowing a DAM thing about thanking apart and fixing head gasket..your videos helpied me every step ... it runs like a champ ..... thank you ....🍻
@freakin635
@freakin635 5 жыл бұрын
Thanks for this entire series guys. IMO you should have shown the application of pushrod tubes and the new one piece base and gaskets. But those are pretty self explanatory if someone has the stones to do everything else this build entails. Thanks again it’s really helped clear a few steps up
@bebop2599
@bebop2599 5 жыл бұрын
Hammer Dan is what makes KZbin awesome
@specialse
@specialse 5 жыл бұрын
Am about to do this job , thank you for pointing out the very important oil bleed down procedure for the rear head assembly .
@stevenboynton52
@stevenboynton52 4 жыл бұрын
Yes thank you I did not know that and was about to do it!
@_Arkenzie
@_Arkenzie 5 ай бұрын
I’m so surprised how easy these motors snap together. Thanks for the wisdom!
@quadzeroo
@quadzeroo 3 жыл бұрын
This certainly helped me big time. Answered many questions in fell swoop. Thanks for putting in the time making this.
@roncrandall
@roncrandall 4 жыл бұрын
I see that you also wear OSHA approved steel toed flippy-floppies in the shop. Well played, sir!
@bryansanford
@bryansanford Жыл бұрын
Expert &&genuine HD mechanic. Thanks for your work on this video. Much Appreciated!!!!
@jakepuls7608
@jakepuls7608 4 жыл бұрын
Thanks for all of the videos! I am going to be assisting a friend of mine refresh a 95 sporty 1200 this winter. In some of these videos, you talk bout a motor sprocket wrench and I was hoping you could elaborate on what exactly it is since we will have to pull the motor on the bike to work on it over the winter. It seems like a handy tool. A little to cold to work on it outside during the winter in Wisconsin!
@johnbrentonlll
@johnbrentonlll 3 жыл бұрын
Ratchet wrench
@6ixstring2112
@6ixstring2112 4 жыл бұрын
Thanks for making this video and explaining everything in detail , you made it look easy for most people to do . I used this video for reference while doing my 99 chief with the s&s 88ci worked perfect 👌
@roberttesch1554
@roberttesch1554 Жыл бұрын
Robert : Thanks for showing these videos they do help people out : THINK'S Again, Dan
@jaklyca8124
@jaklyca8124 6 жыл бұрын
Great video lots of good tips again. Thanks Dan
@stevenboynton52
@stevenboynton52 4 жыл бұрын
Thank you guys!!! Very helpful. Would love to see some vids on a 2012 or equivalent sporty "72". Haven't been able to find many.
@juliancrooks3031
@juliancrooks3031 Жыл бұрын
Thanks for the info, installing rocker boxes today on my 1200 custom
@mchristr
@mchristr 3 жыл бұрын
I'm with you guys. Get the pushrod length correct, install one-piece pushrods, and ride with peace of mind.
@RCTUN748
@RCTUN748 2 жыл бұрын
I have never assembled a Harley before, but I have experience assembling SR400, 5xx many times, after I read a lot of information and videos on the website, I started to feel confident to customize my Harley, so I ordered the 1275 package along with cams and other necessary parts, I hope I will do well.
@rjay2972
@rjay2972 2 жыл бұрын
Couldn't be better on the whole assembly ..great job on my learnings from you.thanks alot...
@steviegibson9226
@steviegibson9226 Жыл бұрын
Awesome video the detail & time taken to explain how to reassemble the top end and torq settings is outstanding I’m in the process of building my own back up thx for the video it’s been a great help 👍👍
@r.cbailey3936
@r.cbailey3936 4 жыл бұрын
Very well explained by putting a rocker box back on your bike great job .would have liked seeing you Putlocker bushings in.
@randallissimo
@randallissimo 2 жыл бұрын
Another great video. I am putting rocker lockers and changing out the gaskets in my 95 XLH soon, this was helpful.
@lynnmaltese371
@lynnmaltese371 2 жыл бұрын
Used this to guide me thru the process of installing Rocker Lockers. Made a world of difference getting it done right the first time. Thanks for an excellent video.
@josephsimons5513
@josephsimons5513 Ай бұрын
do the rocker lockers have to be pressed in I was thinking of putting them in-91 Sportster 883 Deluxe
@anthonysmalawipredators8794
@anthonysmalawipredators8794 Жыл бұрын
Knowledge bombs!! Thankyou, I've been trying to figure out why my front cylinder has excess blow-by. Tons of Google searches and got nothing close to "change the umbrella valve." Guess I need to order me some gaskets
@rjay2972
@rjay2972 2 жыл бұрын
My props up to the hammers outstanding way of showing and explaining...couldn't have been an easier way to learn and complete all tasks..thanks man.....
@thelenius20
@thelenius20 3 жыл бұрын
Thanks Dan, you make best videos and let us know the tips and tricks👌
@javierramirez-kr2yt
@javierramirez-kr2yt 5 жыл бұрын
Thanks man I'm be doing all this soon so it's good just get it my head before helps alot..thanks keep the good work
@openidqd
@openidqd Жыл бұрын
About ticking noise at 26:30 is amazing! Didn't knew. Will check my XB12 on this issue.
@elarr8733
@elarr8733 5 жыл бұрын
The anticipation of that blue locktite, tho.
@musadrew4289
@musadrew4289 3 жыл бұрын
i realize I'm kinda off topic but does anybody know a good place to watch new series online?
@seanjohn467
@seanjohn467 3 жыл бұрын
@Musa Drew I watch on flixzone. You can find it on google :)
@nfan883
@nfan883 Жыл бұрын
Thank you very much for your illustration. I have a question regarding “wait for the lifter to bleed down. ” That is key point mention in your video from 14:10 to 16:00. I plan to replace rocker box gaskets for both boxes because of oil leakage. Do I need to wait for 30-40 minutes when I finish with my first box gasket replacement? Hope I have made myself clear enough? Again, great video, especially for a new guy like me to Harley.
@bowmanchops
@bowmanchops 4 жыл бұрын
Your vids are awesome. Cant wait to buy one of your packages.
@justsurf3328
@justsurf3328 3 жыл бұрын
Ues Blue locktighite? I haven't seen that one before. I will have to check into it. Thanks for the video. I really enjoyed it.
@roberttesch1554
@roberttesch1554 Жыл бұрын
Robert I'm asking is Would you use the same method? installing the rock alarms? On a 2016 breakout in the same manner in this video. or the same way. I got distracted doing something else and I lost focus on what I was doing. If so, you have me on the right track. Just asking to make sure :
@jodywarren2571
@jodywarren2571 Жыл бұрын
great vid! Love the safety footwear too lol. Love this product
@bernardlesperance742
@bernardlesperance742 5 ай бұрын
Excellent ! So helpful ! Many thanks !
@The_PoshBearGamer
@The_PoshBearGamer 4 жыл бұрын
Awesome Video. Helped alot! Thank you
@reddmann2216
@reddmann2216 5 жыл бұрын
Good advice about exhaust push rod being longer...mine are paint coded ...
@reddmann2216
@reddmann2216 5 жыл бұрын
I always run oil up before initial firing...just pull plugs and crank it over. Circulate oil ...listen to make sure no resistance or binding
@rockgear2275
@rockgear2275 2 жыл бұрын
Hi dan, liked your video, what year is this bike you're worked on?
@bradike4564
@bradike4564 6 жыл бұрын
Very nice step by step In detail videos!!
@Mmoose74
@Mmoose74 Жыл бұрын
Friggin awesome! Proud customer here!
@garycb8592
@garycb8592 6 жыл бұрын
Always a Yeah..Great instructions.
@ovlasburning6605
@ovlasburning6605 2 жыл бұрын
Is the red one you put on the rods a particular fat? I'm Italian so I can't understand when you explain. Thx
@pundamilia1191
@pundamilia1191 2 жыл бұрын
I installed the rocker lockers in my twin cam 98 build.
@MrMrEreyes
@MrMrEreyes 3 жыл бұрын
If I'm changing out just the gasket on each level, do I have to mess with the push rods 🤔? I have a 883 single piston buell I'm working on and losing compression around the head area, it's an old bike that sat for a while and no work was ever done on it from the look of the carb when I first started on it. I'm interested on the upgrade top end you offer as well
@austinlane5533
@austinlane5533 Жыл бұрын
Let's say hypothetically.. you install your front rocker box on at tdc and you have very little resistance from the lifters on that cylinder? Is that bad lifters symptoms or just need to be pumped up on start up? They have been sitting on a shelf for 8 months and then got a 48 hour oil soak before install.
@gordonhudson6686
@gordonhudson6686 4 жыл бұрын
Thanks for info i lost a gudgin clip damaged linner so big up grade.
@rp75heavy
@rp75heavy 6 жыл бұрын
Cool I'm getting that noise from rocker arm shaft....!
@GarageBuddys
@GarageBuddys 4 жыл бұрын
Buell X1 vulcan blu 💪😎 i have your 1250 kit in my X1 🔥🔥🔥
@danielgagne485
@danielgagne485 4 жыл бұрын
Sportster motor and Buell The same... Having trouble with my head gasket on my old Blast...This vid super helpful....ere is a question though...Im doing piston, cylinder, and head...Do I need a torche plate? And also, I noticed you used only the gasket...for an older (01), Should I add some gasket sealer?
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
Torque plates are essential when boring and honing cylinders. The head, base, and rocker box gaskets are all supposed to be installed dry. If you don't have a factory service manual, I highly encourage you to get one before working on your engine, it's loaded with valuable information like this and much more. It's really an essential tool for working on these bikes. Only get the HD service manual, the aftermarket manuals are awful by comparison.
@danielgagne485
@danielgagne485 4 жыл бұрын
@@HAMMERPERFORMANCE I do have the manual actually...Thank you for the tip. When confronted with potentially conflicting info, its always best to check with the pros! And, yes, the after market manual inst the greatest...lol
@danielgagne485
@danielgagne485 4 жыл бұрын
Absolutely loving your videos btw. I find these as equally essential as the manual.
@dwaynecorrea9775
@dwaynecorrea9775 4 жыл бұрын
SUPER EXCELLENT!! THANK YA!!!
@DonaldDew-jj7dl
@DonaldDew-jj7dl Жыл бұрын
Wonderful. Thanks
@mmonty8027
@mmonty8027 4 жыл бұрын
Great learning video. Thanks
@caduhoffmann
@caduhoffmann 4 жыл бұрын
Dont you use any kind of black glue (permatex) as a safety measure? I understand that the leak on the rocker boxes are quite common. I have a small one on both and am wondering if i should use the permatex or not.... Thanks
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
I don't, I feel a lot of the leaks come from a rubber gasket getting pinched or kinked. But you surly can use some if you like.
@mattbrady1861
@mattbrady1861 Жыл бұрын
Do you guys sell rocker box gasket kits for a 96 road king evo?
@ihateemael
@ihateemael 4 жыл бұрын
thanks for the vid Dan. I see you use locktite on nearly everything. Do you have to?
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
I would suggest it. If you have the service manuel it will tell you where to use the locktite. When in question use it.
@albertwagner1823
@albertwagner1823 2 ай бұрын
I have a 04 1200 Sportster is it worth putting a 1275 boar on it?
@jackgray1982
@jackgray1982 5 жыл бұрын
Excellent video
@robertwhitlock9768
@robertwhitlock9768 2 жыл бұрын
Awesome videos
@MrGucluoglu
@MrGucluoglu 4 ай бұрын
does it problem rocker shaft hit bolt ? my bike has same problem
@Salvatore3333
@Salvatore3333 5 жыл бұрын
Hi Dan, i have recently converted my 1996 Sportster 883 to 1200, i think to have done all that it's required and rode the bike a few miles but I noticed an oil spouting on the rear cylinder, the exhaust covers and the pushrods cover present a light film of clean oil sweating, what do you think ??, I have changed all the seals to new and even the valves stem seals, shall I re-check the rocker box bolts a re-torque?? i am sure the rear cylinder needs attention..maybe the rear exhaust bolts needs re-torque?? please let me know, thanks Salvatore.
@davidthornton595
@davidthornton595 4 жыл бұрын
Did you end up replacing the little umbrella valves, could be they have hardened up.
@sugaraasagi904
@sugaraasagi904 3 жыл бұрын
Can I use silicone instead of the box head gaskets?
@Xxcdr97xX
@Xxcdr97xX 4 жыл бұрын
Been watching a lot of your videos doing my conversion kit, after getting the front cylinder to TDC on the compression stroke and torquing down the lower rocker box assembly, I wait and keep looking into my intake and exhaust of my head, the valves just don’t seem to be closing. I thought it may have been a stuck lifter at first, so I tore the top end back down and replaced the lifters with some new fueling hydraulic lifters and I’m getting the same problem. I’ve put the cams in several times now and I’m fairly certain that they are correct. Any input?
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
Check your pushrod length using this method: www.hammerperf.com/ttpushrodlength.shtml#method2
@Xxcdr97xX
@Xxcdr97xX 4 жыл бұрын
HAMMER PERFORMANCE I was using a set of -60 solid push rods which I was told would be the right length from the company that did the stage 2 headwork on my heads, starting to lean towards an adjustable push rod now to avoid bending any valves.
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
@@Xxcdr97xX Well, as described at that article I linked you to, a hydraulic lifter is self adjusting. To the extent your pushrods are too short, the lifter lengthens itself to take up the slack, and to the extent your pushrods are too long, the lifter shortens itself to make the valve rest on the seat and keep it from hanging open when it's supposed to be closed. So the exact length of the pushrod is not important, all that matters is that it preloads the lifter plunger within it's self-adjusting range. One way to accomplish that preload within range is to get pushrods of the correct length range. That link I gave you shows how to make sure yours are of the right length range. Another method is to use adjustable pushrods. But as compared to a non-adjustable setup, an adjustable is weaker and it introduces more potential failure points and it's more expensive. So in our view, it's taking a shortcut on getting the preload correct, but it costs more and it's less reliable. That's why we put customers into non-adjustable, heat treated chrome moly pushrods for their builds instead of adjustables, and while we can predict and supply the correct length more than 90% of the time, we still show them how to check it while assembling their valvetrain, just to make sure.
@iamachickenduck
@iamachickenduck 3 жыл бұрын
seriously thank you for the info
@acurarl9929
@acurarl9929 3 жыл бұрын
Are then rockers the same for intake and exhaust?? I disassembled them all to clean are the interchangeable from intake to exhaust???or is intake and exhaust rockers specific to there placement?1996 Harley 1200. Stock rockers
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 3 жыл бұрын
The front intake and rear exhaust as the same as each other. Likewise the rear intake and front exhaust are the same as each other. But different from the other two.
@acurarl9929
@acurarl9929 3 жыл бұрын
@@HAMMERPERFORMANCE if it’s all dissembled for a cleaning how do recognize the back cylinder rockers from the front. It’s sound like your saying ea cylinder has the same rockers as a set but ea set is different from one another?
@acurarl9929
@acurarl9929 3 жыл бұрын
@@HAMMERPERFORMANCE or all 4 rockers are the same ?
@acurarl9929
@acurarl9929 3 жыл бұрын
@@HAMMERPERFORMANCE thank you for the fast response and help very very much appreciated
@acurarl9929
@acurarl9929 3 жыл бұрын
@@HAMMERPERFORMANCE oh oh or maybe I’m reading into it to much yes they are different because the orientation in relation the the valve and push rod makes them different but as long as there over the valve and push rod they are interchangeable. I think I understand
@bee2333
@bee2333 3 ай бұрын
I have a 1990 sportster. Im putting on cams but is it the front or back cylinder that needs to be tdc
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 3 ай бұрын
The correct crankshaft position is when the mark on the pinion gear is pointing straight toward the middle of the number two cam. Neither piston will be at TDC when you've positioned the crank this way.
@jmaxx73
@jmaxx73 21 күн бұрын
I wouldn't think the blue loc tite would work in that hot of an enviorment.
@pixrate404
@pixrate404 4 жыл бұрын
safety first ! I like ure security shoes
@heliojsjr
@heliojsjr 5 жыл бұрын
Great video ! You guys rock !
@iamachickenduck
@iamachickenduck 3 жыл бұрын
you guys rock!!! thanks so much
@darkhorse21xx
@darkhorse21xx 5 жыл бұрын
I was just thinking that a drinking straw might be a bit better to use to find TDC than the zip tie. Just a bit more rigid and wont mar piston surface.
@Cpcsof1
@Cpcsof1 4 жыл бұрын
Is there any way to replace worn rocker ams and shafts without loosening the lower rocker box section to relieve pressure on the pushrods?
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
If you position the motor at compression TDC and remove the 2 big bolts on the pushrod side, you can push the pin out. But you'll never get it back together without removing the rocker box, because the lifter needs to bleed down again.
@Cpcsof1
@Cpcsof1 4 жыл бұрын
@@HAMMERPERFORMANCE thanks for the reply. I have adjustable push rods (ev3 cam) so I could just shorten them to get the rockers back in, then readjust the push rods to their previous length. I have never attempted to adjust push rods, but after watching your video, I am willing to try. I had a feeling that even at tdc, I wouldn't be able to get it back together without shortening the rods.
@Cpcsof1
@Cpcsof1 4 жыл бұрын
One other thing I don't understand. My front intake rocker arm has a shiny spot on it on the valve side from rubbing on the rocker cover. I'm wondering if my push rod is adjusted too loose on that valve allowing the rocker arm to rotate farther than normal when the valve closes.
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
@@Cpcsof1 Hydraulic lifters are self-adjusting. To the extent the pushrod is too long, the lifter shortens itself, and to the extent the pushrod is too short, the lifter lengthens itself. The idea is to select pushrods of the correct length such that the lifter's plunger is approximately centered in it's self-adjusting range, which means a preload of about .100 for an HD lifter (different people have different ideas as to the ideal lifter plunger preload, but .100 is what most recommend). If the pushrod is so short that the lifter runs out of travel trying to lengthen itself, the valvetrain will make a racket and it'll also be really hard on parts because the valve will slam closed rather than be set down gently (this is a common problem when guys accidentally adjust their pushrods at overlap TDC instead of compression TDC). If the pushrod is so long that the lifter runs out of travel trying to shorten itself, the valve will never land on it's seat and you'll have no compression.
@Cpcsof1
@Cpcsof1 4 жыл бұрын
@@HAMMERPERFORMANCE sounds like I just need to file the rocker arm slightly where its rubbing and use the the recommended methods in this video for finding tdc. I really appreciate this video.
@cometrider2000
@cometrider2000 4 жыл бұрын
What is the temperature sensor used for ?
@Oatmeal_TVx
@Oatmeal_TVx Жыл бұрын
it's to let you know if your tires are low
@chriss.8147
@chriss.8147 4 жыл бұрын
Will I have to clearance the rocker boxes if I’m doing a basic 883 to 1275 conversion?
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 4 жыл бұрын
No, and that question is actually covered in FAQ #3 of the kit installation instructions: www.hammerperf.com/ttinstallkit.shtml#faq3
@johnclark7911
@johnclark7911 Жыл бұрын
Thank you...
@shawnleeman5767
@shawnleeman5767 3 жыл бұрын
What would happen if you Mixed up the push rods?
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 3 жыл бұрын
On a Sportster, exhaust pushrods are one length (longer), intake pushrods are a different length (shorter). The actual lengths depend on the year of the motor. If you mixed them up and ended up with an intake pushrod on the exhaust, there's a chance of slack in the valve train because the hydraulic lifter, which is self-adjusting, is unable to lengthen itself enough to compensate for the shorter intake pushrod. This will cause valve noise and also could damage the valve stem, as the normally gentle open and close motion of the cam lobe would get bypassed. Likewise, with an exhaust pushrod on the the intake, there's a chance the valve won't close all the way because the self-adjusting hydraulic lifter is unable to shorten itself enough to compensate for the longer exhaust pushrod. This will reduce or eliminate the compression in that cylinder. If there's still enough compression for it to run, you could be pushing air/fuel mix and exhaust out the intake port and air cleaner.
@dwaynecorrea9775
@dwaynecorrea9775 5 жыл бұрын
Super! Thanks!
@azimyaakub1295
@azimyaakub1295 5 жыл бұрын
Gud job dan....
@EvilRussianBear
@EvilRussianBear 2 жыл бұрын
А для чего Вы мажите болты клеем ?Это вместо локтайт?
@suzukidrz400sm3
@suzukidrz400sm3 3 жыл бұрын
With way does d gasket needs to go
@trevorhenry1003
@trevorhenry1003 4 жыл бұрын
Nice buell
@adrianportuguese884
@adrianportuguese884 3 жыл бұрын
I dropped a bolt in the rocker box
@sirjhonson8218
@sirjhonson8218 4 жыл бұрын
I got that chatter my self.
@shep236
@shep236 3 жыл бұрын
What chatter? Caused by what?
@wickedeagans
@wickedeagans 3 жыл бұрын
U don’t show pulling frame off🥺
@HAMMERPERFORMANCE
@HAMMERPERFORMANCE 3 жыл бұрын
Removing the frame is not necessary to perform this job on a Buell. We just did the video on a Buell with it's frame off because we had one in the shop, and without the frame in place, we could show the process better. But the process can be done with the motor in the chassis, and that's true for either an XL or a Buell tube frame bike.
@WegisWilChop
@WegisWilChop 4 жыл бұрын
10 x 12 = 200
@fagen2222
@fagen2222 Жыл бұрын
Thanks iv just got a 2001 and got to do this work so thanks much
@fagen2222
@fagen2222 11 ай бұрын
Can you give the pull down in feet pounds as that’s my talk wrench
How To Install A Hammer Performance Pushrod Tube Base Kit
31:48
HAMMER PERFORMANCE
Рет қаралды 19 М.
Back to Basics: Evo Sportster Rocker Box Gasket Service
22:37
BiltwellCycleParts
Рет қаралды 43 М.
Mom had to stand up for the whole family!❤️😍😁
00:39
Officer Rabbit is so bad. He made Luffy deaf. #funny #supersiblings #comedy
00:18
Funny superhero siblings
Рет қаралды 18 МЛН
Help Me Celebrate! 😍🙏
00:35
Alan Chikin Chow
Рет қаралды 83 МЛН
Миллионер | 2 - серия
16:04
Million Show
Рет қаралды 1,2 МЛН
Top End Disassembly
41:06
HAMMER PERFORMANCE
Рет қаралды 129 М.
Billy Lane 1995 Harley-Davidson Bad Boy Horsepower Upgrade
27:27
Billy Lane
Рет қаралды 292 М.
How To Install A Sportster Buell Big Bore Kit
22:19
HAMMER PERFORMANCE
Рет қаралды 104 М.
Removing Evo Rocker Boxes & Heads
27:08
Pacific Mike
Рет қаралды 37 М.
Harley-Davidson Evolution engene Disassembly and Re-assembly
58:46
Josip Stanic
Рет қаралды 452 М.
HARLEY DAVIDSON TWIN CAM ROCKER BOX GASKET REPLACEMENT TIPS-N-TRICKS
1:00:52
Harley Lifters & Pushrods Explained: Everything You Need To Know
14:28
Mom had to stand up for the whole family!❤️😍😁
00:39