How to install timing chain cover on 2ZZ-GE with engine still in the car.

[@SaltOfTheEarth1611]

Stopped my oil leak with this tutorial. Thank you so much!

[@2zzlow]

No problem! Thanks for watching

[@carlmatthews6437]

Thank you so much for making these videos. I just did this repair on my 03 matrix xrs. Wouldn't have been able to do it without them. It took me about one and a half days of steady off and on work. Also a tip, I didn't have to remove the ac compressor, It makes for tight clearance on one of the chain cover bolts but otherwise I would assume it's easier.

[@2zzlow]

my hands are big and the ac compressor is only held by 3 bolts so its not much for me to remove but thanks for the tip, might help others.

[@bboyck]

My Dad and I just tackled this project and all appears well--we had an oil leak near the chain tensioner towards the firewall but it appears OK now. Thank you! I wanted to provide context to the last 2 minutes of the video. IMPORTANT: BLEED YOUR COOLANT OR YOUR ENGINE WILL OVERHEAT! The process involves running the motor with the thermostat open and the coolant reservoir elevated in order to bleed air from the system.

[@2zzlow]

Fantastic! lol yea i guess i should of noted that but if you got that far into the job im sure you would know to bleed the system

[@McHotTopic]

Shout out to Hector for hooking the homie up. Good to see he’s still around after going legit, NHRA homie.

[@dadadadada4974]

Wow, great video! I like how you note the bolt sizes and torque spec for each step. Toyota should hire you to make service videos.

[@2zzlow]

Lmao I was borderline not going to throw in the torque specs but I knew someone was going to ask so I spent a few hours reading through the Toyota service manuals and writing them down to review them over in the video.

[@zerosevenpro]

@@2zzlow thank you for that .

[@chrisa8648]

@2zzlow. For the water pump pulley i use an allen wrench that ffits pretty good in there, and just turn it until it bumps the water pump to start removing those 10mm. Same when installing. Ive done many Toyotas WP like this and works every time. Just wanted to share with you. Good videos by the way.

[@2zzlow]

ill for sure give it a try next time. appreciate the different approach.

[@tanker242]

I know the differences between the 1ZZ and 2ZZ, but they are similar enough this video has a lot of good information for both engines (major difference is the use of FIPG gasket all the way around for the timing chain)

[@2zzlow]

thanks fam

[@craig357]

Great video. Sadly my mechanic never put the 4 spots of RTV and leak came back so thanks for pointing that out and the torque specs.

[@2zzlow]

I really hope he takes care of you for this...that sucks bro

[@craig357]

Have you ever put seafoam down your spark plug holes? @@2zzlow

[@jacksoncook1866]

just reinstalled the 2zz after pulling the motor and ling down to the headgasket. its leaking a bit from the timing chain cover still and im almost sure it was from the packing seal i didnt put XD going to try pulling it off an applying that where u said and hope fore the best !@@2zzlow

[@richardmorse5307]

I agree this is a great video! Your information on torque settings is awesome. Thanks for posting.

[@2zzlow]

Glad it was helpful!

[@puregsr]

Word of advice, I put a 17mm socket behind the dowel pins and flip the cover around, hitting them with a brass hammer, slowly and carefully push them out a little to assist in power steering pump installation.

[@2zzlow]

great tip, ill remember it for the next time around.

[@Nikothemoneyking]

Such a good video very detailed this is the kind of detail home mechanics need thank you sir!!

[@2zzlow]

Glad you enjoyed it!

[@judest818]

Great video, I'm planning on doing this on my Corolla xrs MLK weekend. My friend that's a Toyota tech in Chino told me it's doable without removing the engine but a PITA... He also warned me about the chain tensioner, which I'm still confused about, but will probably understand later. Yesterday I was cleaning around timing chain valve cover and passenger control arm/suspension area and there was serious fucking gunk almost sludge like stuff in that area. Has me worries... But engine oil isn't sludgy when removed from the pan. Got lots to do. Thanks for informational vids!

[@2zzlow]

Just remember for the Corolla XRS you need to remove the exhaust manifold because the air injection tube that hugs the timing chain cover won’t let you remove it without taking it off. It’s not the worst thing but I thought I’d let you know before you tackle the job. It’s not hard but it’s very time consuming.

[@judest818]

@@2zzlow thanks for looking out! We'll see how it goes in a few weeks... Just procuring everything. And enjoyed the nights into dreams reference! Not many g's know about the Saturn!

[@logikal3d]

@2zzlow, Cant thank you enough. I just wrapped this job up and not a single leak to be found!

[@2zzlow]

no problem! take care

[@reddemon52]

Great video bro I'm just amazed at how the underneath does not have rust. I stay in chicago and the snow just rusts our cars out.. I try not to drive my celica in winter.. bro what about the TRD super charger any videos on possible future install

[@2zzlow]

Trust me their is going to be a lot of content from that

[@kmlumd44]

I did this on my 06 vibe gt. Tips: no need to remove ac compressor. Use oem gasket on timing chain tensioner or buy gasket from toyota dealer. If you break the nut or round it on ur belt tensioner u can use a c clamp to compress the piston and not have to replace the tensioner.

[@2zzlow]

Left the same comment 4 times I see.

[@monkchief5696]

When u say to disconnect the fuel injectors to prime the engine . How exactly do you prime the engine ?

[@2zzlow]

No fuel delivery so crank spins not allowing the engine to turn on to build oil pressures

[@CoBlaze656]

Just got to that part and was wondering the same thing.

[@adventures223]

Excellent detail and explanation just wish you would of showed the dis assembly but very professional thank you

[@2zzlow]

I have a 40 minute detailed video on how to disassemble, check my channel

[@adventures223]

@@2zzlow my fault thanks i will check that out and subscribe to your channel love how professional and detailed you are

[@kmlumd44]

Dude thanks for making this. My 2zz vibe gt wont be pissing oil anymore. Maybe it will start having more confidence. Thanks for doing torq specs and rtv locations. Do u do a video with parking brake line replacements? I got no ebrake and it's cause the line's stretched. So i got new lines but i ain't sure how to tackle it.

[@kostaskosta7617]

great video my friend ,for to do that job must bring out the oill im asking because i m resently change the the engine oill

[@2zzlow]

you dont have to change the oil but i do it just in case something fell into the oil pan

[@kostaskosta7617]

Thanks my friend for that video I do it my self and it wark I save some money

[@kostaskosta7617]

You're a good engineer

[@CoBlaze656]

Instead of hammering the sliding dowels in for the power steering pump I just pressed them in using a ball joint/bushing tool. Also my timing chain tensioner was near impossible to get off, but I couldn't even pry it out, so I ended up wiggling the cover off with the tensioner still in. Bad idea, though, because some black plastic piece came out with it 😅

[@CoBlaze656]

Figured out that it was a piece of the timing belt guide that's closest to the tensioner.

[@YeehMate]

Just did this job with aftermarket gaskets, pretty sure its leaking worse than before Lmao going to try retighten all the bolts and see if that helps Worst case ill have to buy oem gaskets and redo the job

[@2zzlow]

for a big job like this i wouldn't trust aftermarket

[@Brandon-sk5lq]

Need to do clutch job on 2006 Corolla Xrs and it also needs a timing cover gasket. Would it be easier to just pull the engine and leave tranny in car. I'm just worried there is not enough clearance to get engine out and clear input shaft. If I was able to pull engine I could easily to the gasket and clutch and leave drive train intact.

[@2zzlow]

id pull both out. the amount saved once the engine is out to do the timing chain cover gasket and unbolting the exhaust manifold is worth it

[@PooL10Steel]

Hi, what kind of ATF transmission fluid you recommend? The one on the video is Valvoline MTF and my car is automatic, thanks :)

[@ptbruiser2243]

I would gladly pay you to do this to my sons 2000 GTS. Tired of it leaking oil on the driveway

[@2zzlow]

If you are serious and within the area message me on Instagram

[@ptbruiser2243]

@@2zzlow I am 100% serious, Sadly you live too far from me so i'm stuck doing the job myself. But your video will def help me out

[@dadadadada4974]

So how do you jack the engine without damaging the oil pan? Is this safe to do? I need to change a passenger side 2zzge motor mount and will need to support the engine. Any help or ideas?

[@marcsova7411]

hmmm....howd you rotatwe the crank counterclockwise after the chain tensioner install with the pulley and nut off the crank?

[@2zzlow]

I actually let go of the lock pin from the tensioner manual through the inside

[@AmeriFanPicker]

2zzlow ahhhhhh. Duh (that's me above noseartguy...for whatever reason when I commented on my laptop it's my name not my handle).

[@juanbarraza5604]

Can I replace the oring on the plunger my 2zz? Engine leaking oil. So counter clock wise from the point of view of the pulley?

[@2zzlow]

yes and yes.

[@sl0wyota2zz]

bruh. i would literally fly you out to Houston to do this job for me lol i need this done badly and i dont know who to trust out here!

[@2zzlow]

Its not that hard. i feel people get discouraged because of how long it takes.

[@christopherfilipone2327]

Hahaha. I can do the job easily. 400$

[@investedcrypto9210]

@@christopherfilipone2327 where you located?

[@ambitiousseeds7346]

hey bro, can I remove the 2zzge from 05 matrix xrs 6 spd manual without having to remove the transmission? and is it a good idea? i wnat to avoid removing the tranny unless i have to. please let me know.

[@toufuevang-c3z]

@2zzlow serious question.. would you be willing to do this for my matrix xrs? I live in sacramento and from your other videos you live close by. Just give me a price and if it's not to bad I rather trust you then random shop that's never done it before

[@efrinramos6476]

Saludos necesito piezas para una matrix xrs 2004 hacerte agunas preguntas mas como podriamos comunicarnos. Muy buen Video

[@2zzlow]

mandame mensage a instagram

[@hokutonova]

Hi 2zzlow! First, thanks for uploading such great video. I have a 2003 Matrix XRS, I'm planing to change the timing cover gasket, but I don't understand what's the reason to remove the 2 "LIFT BOLT"?

[@2zzlow]

Just preventative maintenance

[@shawnO432]

Do you recommend the valvoline synchromesh over all the other mt fluid for the 2zz

[@2zzlow]

Yes!!!! That’s what I actually use in all my cars. Orileys sells it way cheaper than monkey wrench racing.

[@marcsova7411]

What torque wrench you have do the low end torque settings? I love my harbor freight icon but it doesn't go down that low. I have their cheaper Pittsburgh inch pound wrench but it's not nearly the wrench that the icon is. It's hard to even make sure you have it set on the correct number. Got my gaskets and such in the mail. Man...I'm amazed at how thin this timing gasket is. I guess I was expecting something a bit more like the engine cover gasket...a little more beef to it.

[@2zzlow]

I have the Pittsburg harbor freight torque wrench and it worked enough for me. Exactly on the gasket part

[@AmeriFanPicker]

2zzlow yeah it works...I just feel like the markings are not that precisely engraved on mine anyhow. Maybe I'll see if I can exchange it. Oh and speaking of chincy parts...for my oem belt tensioner. Wow that thing feels cheap too. Lol.

[@beats622]

Replaced mine. Used all new gaskets. Got a coolant leak from where the water pump mounts (new oring) and the timing cover in that same area. I took out the water pump, put the original one back in and used some gasket maker around the mounting holes. That leaked stopped. The other one remains. Any ideas?

[@2zzlow]

did you make sure to put the bolts in the correct hole? remember 2 of the 6 are different

[@beats622]

@@2zzlow ya I did. I ended up taking everything apart and found the timing cover was cracked pretty bad. One snug too much. I got it welded to hold it together for now. I ordered a used timing cover to replace with.

[@marcsova7411]

slowly working up the balls to do this in-car on my 04 matrix xrs....if its even possible? That metal tube from the air pump to the exhaust manifold(?)....is it even possbile with that in the way? I wish the factory shop manual was better on certain procedures. I do have an 03 ECU so I guess I could delete that pump and pipe...what would be involved in that?

[@2zzlow]

that is the air injection tube. you need to remove it from the exhaust down pipe and from the engine. you can then move it out of the way. you cant just swap ecu, you need to plug up those holes on the back of the engine block.

[@AmeriFanPicker]

2zzlow what I mean is...I've been running an 03 ecu. And I'm pretty sure I can pass smog this way. If so...then I'd consider deleting the pump and tube etc.

[@noobzhero]

Thanks for sharing bro

[@2zzlow]

no problem

[@nat15.9]

Please advise if I could follow this video to re seal my 3zz (Altis 2004) ?

[@2zzlow]

not the same

[@brinho109]

The torque specs for the engine mount would be the same for a corolla xrs right?

[@brinho109]

Never mind, they are the same after all. Doing this on a corolla xrs with 96k miles the gasket actually was in good condition (all the gaskets were changed of course). Despite the bad leak (oil covering the power steering pump, most of the timing cover) I think in my case the FIPG from factory on the 4 spots of the engine didn't hold up well.

[@2zzlow]

yea that also tends to fail and become very brittle over time

[@brinho109]

When you mention disconnecting the fuel injectors before priming the engine, are you simply turning the engine over with the fuel injectors out?

[@2zzlow]

Yes, simply priming the engine so that it doesn’t start without oil up on top. I just disconnected the power to the fuel injectors

[@brinho109]

@@2zzlow Ah ok. Could this whole procedure be done in a corolla xrs or would you have to take out the engine?

[@2zzlow]

You need to remove the exhaust manifold and get it out of the way. The air injection tube coming from the exhaust manifold hugs the timing chain cover.

[@deesmas]

Mine can be your 7th car! P0012 code is kicking my noob butt! Changed the oil, timing solenoid, lift solenoid, and crankshaft sensor for giggles. Dont want to mess with my timing myself. Ugh

[@2zzlow]

bring it over and i can look at it

[@ryanwright7836]

What mileage did you do this at? Did you experience or fix any rattling, or was there any significant chain guide wear? I am 250k and have very annoying rattling coming on at 2500rpm under load

[@2zzlow]

170k no chain wear guide, no rattling id suggest replacing the timing chain tensioner and see what happens.

[@BayAreaWrecker]

It's been overdue on my Celica it's been leaking a bit , it gets on the belts and makes a nasty squeaky noise , could this be done in a day or two?

[@2zzlow]

It’s only going to get worse. Do it now before the oil goes all over your car and it’s hard to reach areas to clean it up. This job can be done in a few hours if you are dedicated.

[@kaeosfactory]

U mean do it b4 it makes your belt slip and get cooked. High RPM plus oil equals surfing belt on pulleys and the belt will get squishy and the end is worst, it explodes. Into a million pieces. And then u overheat and if u are on the highway at night, dead battery trying to get off the highway. Yea. It happened to me.

[@SuperEliflores]

Bro how did you clean that power steering res. it looks squeaky clean

[@2zzlow]

Purple power and a pressure washer

[@SuperEliflores]

2zzlow did you just dump it in and let it sit over night? Then power wash?

[@2zzlow]

I let it sit for a few minutes, shake it and then pressure wash it. Repeat this process like 3-4 times

[@SuperEliflores]

2zzlow thanks man I’m going to try it I don’t have a pressure washer but gives me an excuse to buy on e

[@tk2tone883]

Thank u

[@2zzlow]

No problem

[@zerosevenpro]

Hey did you ever make a video on how to clean the 2zz before installing the cover?

[@2zzlow]

i can if you want me to

[@andrea981]

@@2zzlow That would interest me too, I'm doing this job right now

[@mengx94]

Lots of brake cleaner. Lol

[@andrea981]

I ended up using a degreaser on a rag (not directly on the engine)

[@AmeriFanPicker]

How do you hold the crank for torquing the nut?

[@2zzlow]

I just use an impact at medium settings and ive been fine.

[@AmeriFanPicker]

@@2zzlow oh wow thanks. You know what size torx socket you need for that threaded torx bolt that holds the tensioner piston???

[@45Ballistic]

Thanks man this helped a lot. I wasn't as careful as you said on the motor mount and I cross threaded it. Would you know the bolt size for the 14mm that connects to the chassis?

[@2zzlow]

m10 i believe?

[@45Ballistic]

@@2zzlow Cheers mate, that did it. You're definitely a more reliable resource of 7th knowledge than the celica forums.

[@jayns1]

Were do you order your parts just curious

[@2zzlow]

toyota parts deal

[@johnproniewicz4840]

How did you get the power steering pump back in? I'm currently stuck because I didn't realize I needed to move the pins. Nothing seems to work. I need 1mm more clearance to slide it back in.

[@2zzlow]

use a hammer to slide the dowels out a bit

[@johnproniewicz4840]

@@2zzlow I appreciate the quick reply! I ended up getting a 3"full threaded grade 5 bolt, a nut, fender washers, and a socket that went over the dowel. Had them moved quickly with very little effort. On another note. You can take out the long threaded bolt for the upper mount of the belt tensioner with a 6.5mm socket. Made the job ten times easier. Again, thank you for the quick reply! Your channel and videos made it a fairly easy job.

[@remues5]

mine is leaking too, how much you charge to do it? planing to take to a shop but i don’t think they will do as a good job as you and i know they not going to torque it to spec. lmk thanks

[@2zzlow]

where are you from? $300 labor only

[@zelevdivad]

Hi Sebastian. Awesome channel!! btw. I’m located in Tracy Ca and recently found your channel. Do you offer your mechanic services? I have a 1999 Corolla with 6spd with this exact problem. I don’t have a Instagram or Facebook. Hope this finds you well.

[@2zzlow]

sorry, been extremely busy with life atm

[@kaeosfactory]

Come help me do mines. It’s cold AF. ANYONE HAVE ANY LEADS ON A 2ZZ rotrex supercharger mount bracket????

[@Craigz1000]

Contact se7en Motorsports in UK. They may be able to help? www.se7enmotorsports.co.uk

[@2zzlow]

Get me a plane ticket and I’ll do it hahaha

[@kaeosfactory]

2zzlow I wish.

[@carloscrod_]

Hey 2zzlow!! My name is carlos, I’m currently on the way home from the Bay Area back to my hometown Santa Rosa. I just finished checking out a 2006 XRS!! The guy wants 4000. While test driving it I got some weird noise shifting into 3rd. I’ve read that 3rd and 4th on this C60 transmission. And the seller also mentioned that I should beware of the clutch in the future months from now. I told him I would be back Thursday with cash in hand. Is there any way you can skype me and explain what’s wrong with the 3rd gear and how much a new clutch would be? Or get on a quick phone call. Or maybe just a response? I’d appreciate anyone else’s input onto what is going on with this car I’m trying to buy.

[@2zzlow]

hit me up on instagram