How To Make 6-Channel Radio Control. Range 2000m+

[@Kendin-Yap]

English voice-over version: kzbin.info/www/bejne/aYG4paF9rcyHrassi=PAMtKNvQ6HXRnStA Tükçe seslendirmeli versiyon: kzbin.info/www/bejne/Z3O7c4WlpaeAnacsi=4Qdpy6o2me6jdAfT If you like my projects and want to support me to make them sustainable... Patreon: patreon.com/KNDYP KZbin JOIN: www.youtube.com/@Kendin-Yap/join

[@MelicaMari-Ni-Goon]

can u make the gerber file for 8ch remote plz

[@Kendin-Yap]

www.rcpano.net/2023/12/30/how-to-make-6-channel-radio-control-range-2000m/ @@MelicaMari-Ni-Goon

[@MelicaMari-Ni-Goon]

@@Kendin-Yap ooh thanks i didn't notice u have done 8 channels version

[@smoochies5056]

@Kendin-Yap it is ok to use ams117 ldo on this ebyte?i just need to add 2x 100uf?

[@gourabdutta9331]

Your 6 channel gerber file didn't download

[@Andrew-rc3vh]

The thing about 2.4Ghz is that back in the day when the authorities were deciding which portions of the radio spectrum they could licence out to make money from, the 2.4Ghz band was seen as worthless because it is one of the absorption frequencies of the water molecule. After deciding it was useless for radio communication the microwave oven was discovered by accident by semi cooking a bit of food someone was messing about with due to this very effect. Anyway, due to the low quality of the band the authorities decided to make it licence free and this is why we use it for wifi. If you are looking for range then the thing is not to use this band. The 870mhz band is better. Generally the higher the frequency the more the air attenuates the signal.

[@mixeduptv2268]

If range matters enough, you don't built your own transmitter & reciever. It's a fun project. Plenty of range with 2.4Ghz ELRS for most people also. If range matters only then there's satellites.

[@leopoldomolina1763]

Your comment is very informative 👍🏻

[@davidwalker4795]

Ok

[@Andrew-rc3vh]

@@mixeduptv2268 I understand ELRS uses spread spectrum. You can trade bandwidth for range either by using narrow band modulation or as spread spectrum does, it works like statistical averaging to increase signal to noise ratio and uses a wide spectrum. You can go as far as you like with this method until you run out of bandwidth. Also bear in mind the rules say you can only transmit

[@onmyworkbench7000]

I developed a system similar to this to be used in The UAV Challenge - Outback Rescue about 16 years ago. I incorporated it into a Futaba 6 channel 72 MHz transmitter after removing the 72 MHz RF section from the transmitter case. This allowed all of the ATV's, servo mixing and servo trim levers in the transmitter case to be utilized in the new 2.4 GHz system. I have a video of it on my KZbin channel. KZbin won't let me put a link to it.

[@hayreddinguzel6630]

Elinize emeğinize sağlık yaptığı projelerin dosyalarına kadar paylaşan nadir kişilerdensiniz. Buda sizin amacınızın sadece video çektim bitti olmadığını gösteriyor her vidonuzun altında bütün detayları bulunuyor. Teşekkürler

[@steliostheodoropoulos7304]

Congratulation. Very nice project and detailed description. Happy new Year !!!

[@antonioyzarra651]

I'm finishing watching this video and it seems like an extraordinary job! I want to thank you on behalf of those of us who are looking to do something and make it work, this work of yours is far beyond what any mortal can do, it is like a work of art dedicated to those who like excellence and meticulous work Thank you and may your success continue. Estoy terminando de ver este video y me parece un extraordinario trabajo! quiero darte las gracias en nombre de los que estamos buscando hacer algo y que funcione, este trabajo tuyo esta mucho mas alla de lo que cualquier mortal puede hacer, es como una obra de arte dedicada a los que les gusta la excelecia y el trabajo minucioso, gracias y que sigan tus exitos.

[@kadalkadalan3618]

I just reading your article nrf24 conection problem.Now everithings is better.Thanks..for your time.

[@zaidkabir7277]

Thanks sir the one you have made last time was very complicated. This one however is simple yet reliable 😊

[@ordinaryperson6703]

Muhteşem proje üstat. Video da gayet açıklayıcı olmuş. Ellerine sağlık

[@thavaclk5242]

I will write in my language. Videolarınız sayesinde bu alana ilgim arttı. O zamanlar 9. sınıftım. 2 kere teknofest iha yarışmalarına katıldım. Çizimleriniz , uçağı yapma sürecinde işime yaradı teşekkür ederim yolunuz açık olsun.

[@thavaclk5242]

( Turkiye Teknofest )

[@morekmek]

bütçe vs. alabildiniz mi?

[@bobski1151]

You showed me allot on how I can improve my radio controller, thank you.

[@r.safarov]

This is what l wanted, thank you

[@asgassauro]

I really appreciate this content. Keep going. U’re fenomenal 👏🏻👏🏻

[@mr.indianhacker2487]

I wish to pray God your channel growth fast.

[@omerbilgin5323]

Bir eem olarak seninle gurur duyuyorum hocam .tebrikller.

[@omerbilgin5323]

hocam bizde takip ediyoruz. ama pek yorum yapmıyoruz haberin olsun. sayende yıllardır bu hobiye başlamak için beklediğim ancak bi türlü cesaret edemediğim işler için ilk siparişimi verdim. teşekkürler emeklerin bizi de cesaretlendiriyor

[@omermatur6018]

Usta eline sağlık açıklayıcı ve öğretici 👍

[@alewarte]

This tutorial for sure fun and educational. I'm waiting part 2 with stability and range tests :)

[@qnaman]

i'M USING SIMILAR SETUP. ALTHOUGHT i'M USING STABILISERS FOR 5V AND 3.3V BECAUSE OSCIALOSCOPE SHOVED ME SOME ABERRATIONS IN SOME CASES.

[@kevinwilliams8951]

I enjoyed watching your electronic hobby thank you for telling me what each part is, the coding you where doing I have no clue, I will watch this again thank you

[@Kendin-Yap]

For coding ... kzbin.info/www/bejne/nGLdaYqsrpppqpo

[@vdm7776]

thanks for the video! I'm waiting for next generation with display and menu to ajust limits and consumptions for servo and ESC. :)

[@davideliasfloresescalante8840]

Thanks a lot, these will be just for my rc plane project Im about to start... Great how-to

[@mehmetozan74]

Yine döktürmüşsünüz.

[@MrSobreviviente33]

Great, change the antenna for 1/4 ground plane and the range will be higher. This antenna is very simple and cheap. try it!

[@mr.indianhacker2487]

Nice you are genius bro.

[@mohamedbatitimohamedbatiti4674]

Very nice work my brother

[@hamadabob3823]

شكرا جزيلا اتابعك من الجزائر لقد افدتني كثيرا

[@Creative_file_0369]

Sir subscriber from India and I am very big subscribe

[@lefablabdequoy8301]

congratulation, that is the coolest project ever seen !... thanks for sharing ...

[@gayanijanathari]

Excellent brother. Please make lora 20 km range 8 channel transmitter and receiver with LoRa module

[@yerbudak]

çok güzel bir çalışma olmuş. ellerine sağlık

[@enesbalc56]

Ellerinize sağlık çok bilgilendirici bir video olmuş

[@burstfireno1617]

Harika çalışma Allah razı olsun :)

[@herbi102]

Neat, beautiful, all in all beautiful!

[@ovalwingnut]

ShOcK & AWE COoL. 100 points awarded! Truly SUB worthy. Thank you for the video and the detailed punch lists.. Cheers from So.CA.USA 3rd House On the Left. It's true what people are saying... You do RoCk

[@adunsky]

Great project! Do you have any projects involving an IMU ?

[@Jirawats]

Great job, i love this

Üstad eline sağlık.

[@mr.chetow771]

good instructions, I like your videos...

[@eon147]

eline sağlık abi çok güzel olmuşş

[@Origami-786]

Wonderful creativity ❤

[@richardtittle351]

In the UK you should use channel numbers of 80 or less because the max frequency allowed is 2.4835 ghz

[@sotm6078]

If only you did something that really worked.

[@Kendin-Yap]

It works perfectly when everything is done correctly.

[@mitsos_306]

This is another great video! Thanks a lot for you time and knowledge. I would like you to make a video with Arduino mega and 10 channels!

[@selcuktnt]

Efsane olmuş ellerinize sağlık

[@ripmax333]

A really nice and beautiful project, no doubt about it. But is it worth it nowadays doing it yourself instead of buying a 6ch Tx brand new for little money.

[@SteSOTAGIsarl]

great job thanks for sharing

[@RoshanYadav-ft5ih]

Bro love you you are the best really like you You are the best

[@daddybou8567]

Great project 🎉 . Is this transmitter/receiver PPM or PWM ?

[@Kendin-Yap]

Thanks. PWM

[@muhammadm1237]

Man you’re awesome 👏 you have to

[@taha06.]

elinize sağlık. uçuş testleri de gelir mi ? ben de yapmak istiyorum

[@sahancooray5076]

Can we find the parts in an electronic shop and it is nice 🎉

[@JonasBrave]

PCB'leri uygun fiyata temin edeceğimiz bir yer yok mu?

[@yahyayahya-uf6bc]

Professor, I ask you a question: Can I change the cardboard that you use in making airplanes with regular cardboard?

[@Kendin-Yap]

Regular cardboard is a heavy material. It will be very inefficient.

[@emrhncooll]

Ne Harika Bi Adamsın Sen Ya

[@fastcustomscooters9450]

Love video you got add ons to mix aleroins and evelation with 2 servos if could design be good thanks ian

[@sonaldey1394]

Great video. Can you make one with expo and dual rates?

[@aboareef-jk1xv]

Teşekkür ederim videolarınız uçağımı yapmamda bana çok yardımcı oldu Sana bir soru sormak istiyorum Bir fırça motorunun kaç volta ihtiyacı vardır?

[@Streakgamerofficial]

Please Do a Range Test

[@AmruMagdy]

جزاكم الله خيرا اخي الكريم ❤

[@afdsd]

Awesome!!

[@gayanijanathari]

Excellent brother. Please make lora 20 km range 8 channel transmitter and receiver

[@ozgunugzo]

Thank you so much ☺️

[@PeterNebelung]

Looks pretty interesting. Where do you get the board, and parts?

[@Kendin-Yap]

The motherboard is not a ready-made product. I designed and prepared it. Links to the necessary information and materials are below the video. Click or tap "more" to see the entire detail section.

[@PeterNebelung]

@@Kendin-Yap Thank you.

[@intelligence482]

Now this is nice

[@hamasharazury7156]

Please post a tutorial on making a copy of the microzone controller❤

[@SPANDANDHARA-ss2ry]

I want to purchase this readymade, what will be the cost ?

[@usr6106]

tebrik ederim süper olmuş, trim ayarı için pot koyulabilir belki. 😊

[@Atpgamer1234]

Bhai ye board transmitter or reciver ka kahan say milay ga bhai reply zror ker kay batana

[@Kendin-Yap]

These are not commercial products. The link to the files you need to do it yourself is below the video. Or there are companies (such as PCBWAY) where you can get PCB printing services. You can get a prepared PCB by sending those files to them.

[@ToPProjectsCompilation]

Hi Kendin, your projects are great. We want to feature them on our channel (with proper credits). If it sounds good, then kindly reply.

[@SciencewithTejas]

is it necessary to use a ceramic 100nF capacitor or using any other 100nF capacitor would be fine?

[@ardayokus3167]

Merhaba, projenin masrafı ne kadar tuttu ?

[@Kendin-Yap]

Hesaplamadım. Çünkü parçaları farklı zaman aralıklarında almışım.

[@anshumantripathy5215]

pls make a videos on how to make the pcb

[@RamSingh-qx2ev]

Jitna isme kharacha karo utne me ek acha khasha transmiter aur reciver aa jaye

[@erkuts6546]

Menzil ölçümü yaptınız mı?

[@johnchoice1371]

It would help if you talk/explain while performing each step.

[@funnyprankforlaughter1388]

Hi wonderful job Can you make remote control for agricultural spraying drone

[@vaishacnambiar1131]

Could you make a vedio on upgrading a existing flysky radio transmitter, specifically the CT6B model. Which needs 8 batteries, that too which dries out in less thab an hour and the range is shit plus the servos vibrate(unwanted motion) when operated via the transmitter

[@DaivyDjimbi]

we are whaiting to see the PCB video of your 8 Chanel 2400..

[@Kendin-Yap]

I have published the PCB files (PDF and Gerber) for receiver. The transmitter is not suitable for PCB. Because it is built with a lot of long cable connections. There is a possibility that I will add gerber and pdf files regarding the 8 channel option to my website in the future for the new 2000m+ version.

[@norbertocasa5845]

Las interferencias en 2.4 generalmente son provocadas por los enlaces de videocamaras entre nodos.

[@Omersalih053]

elinize sağlık güzel video sorum şu: düşük tetiklenme değeri olan (30mv) bir mosfet biliyormusun yada benzer bir mosfet varsa oda olur

[@Kendin-Yap]

Bilemiyorum. Araştırma gerektiren bir konu

[@Omersalih053]

@@Kendin-Yapflysky i6 alıcısı için o mosfeti arıyorum sinyal ucundan arduinodan alıştığım gibi 5v vermiyormuş ölçü aleti ile ölçtüğümde fark ettim

[@Allah_Is_The_creater]

Is 1400 kv brushless motor work well with 8045 propeller? In turm of thrust and speed and avoid overheating?

[@dudycezemer6473]

I wanted you to teach me how to boost these 5.8ghz and 2.4ghz signals so I can go further. I'm from Brazil

[@hasancinar4664]

Hocam bu projeyi birde Lora e22 modülü ile yapsanız harika olur

[@AFSMG]

I have a prototype of a radio controlled golf cart. I am looking for a transmitter and another radio receiver. They should be configurable so that one car does not interfere with another. I would need at least 100 meters of closet. Can you recommend any? I think they must be 433 Mhz, due to some permissions problem. Thank you very much.

[@MirceaPrunaru]

Thank you!.

[@amitkumar6784]

Bro your transmitter and receiver have many features

[@rajgaurav2580]

IS IT AS GOOD AS COMMERCIAL ONES ?

[@SagarKumar-888]

BHAI ye plets kaha se parches kre digital jo isme ye component feet krne pade

[@aberateklehaimanot9804]

great project and thanks for sharing,i have issue opening the gerber file though.and i have many nrf24l01 but i am still not able to make them work any of them.i am just clueless where the issues are.did you ever encounter such issues as well?Thanks again.

[@ДенисКнязев-н9с]

Здравствуйте, нужно обернуть плату NRF обычной фольгой, но перед этим каким нибудь диэлектриком, например скотчем или изолентой, и если не изменяет память, ещё нужно подпаять керамический конденсатор на 10 pF, на пины питания, и тогда у вас всё получится!

[@wonderscraft]

How to upload Gerber file and what's the size of board in mm. Please reply

[@Kendin-Yap]

PCB board size Transmitter: 114 x 65mm Receiver: 60 x 45mm

[@wonderscraft]

@@Kendin-Yap Sir please make a video on how to upload gerber files and place our order . I am not able to understand how to place the order of transmitter and reciever seprately .

[@Kendin-Yap]

I made the PCB board with the PDF files I prepared. If you want to do it yourself, you can use the PDF files in the link. Those who are interested in electronics at a hobby level usually do it this way. If you want to have it done by a commercial company that provides PCB printing services, you need to send the Gerber files to them. Example PCBWAY. How to upload gerber file to sites like PCBWAY? There are many videos on this subject. It is possible to learn by watching them.@@wonderscraft

[@wonderscraft]

@@Kendin-Yap thank you

[@mehmetyaman9385]

çok başarılı bir çalışma olmuş tebrikler. Ancak sizin kullandığınız gibi PCB leri nasıl temin ederiz 0:18

[@Kendin-Yap]

PCB yi kendim yaptım. Onu yapabilmeniz için gerekli dosyalar linklerde mevcuttur. Diğer seçenek pcb hazırlayan ticari firmalar da var. Onla için gerekli gerber dosyaları da linklerde mevcuttur.

[@7UN4]

Love this variation like all the other versions, I have all the components, make the connections one by one and checked the cables multiple times, somehow I can't make it work. The nrf24l01p modules are not communicating with each other. If you had similar problems or have any suggestions I'm all ears. I tried it with newly bought nrf modules and arduino nano's. I am really curious about what I am missing.

[@7UN4]

Also tried different and simpler codes, Tried connecting the cables directly and to 3.3v of arduino nano without that extra regulator circuit, Supplied nanos with various voltage sources, lipo's, USB ports, lab power supply, I am quite frustrated and I am not kidding its been at least 10 hours just to make it work in these last 3 days. :')

[@7UN4]

Still trying, managed to make a code work but now the receiver cannot communicate with the radio, sender is constantly sending packages but no one to receive on the other hand.

[@Piotr_Kuligowski]

Could you explain why those capacitors are needed? I did something similar but without them and it worked. FYI I am electronics begginer.

[@Kendin-Yap]

Capacitors provide more stable operation. And it filters out electrical noise.

[@christjanehusacek4911]

Cooles Projekt, wo bekommt man die Platinen?

[@Kendin-Yap]

I made the PCB boards myself. The necessary files are below the video.

[@LaMin-ri6eg]

thanks a lot❤❤

[@daimichi7165]

Great video！　Are 10uF and 100uF electrolytic capacitors both 16V?

[@Kendin-Yap]

16V or above can be used.

[@Kendin-Yap]

If a battery with a voltage higher than 4S is to be used, it should be above 30V.

[@daimichi7165]

@@Kendin-Yap thank you very much!

[@drminiz]

Yeni gördüm hocam RCPANO sizin miydi ? Yıllar evvel ilanlar yayınladığımız site değil mi bu ?

[@Kendin-Yap]

Evet doğru

[@syntaxsaga]

If I replaced the toggle switches with momentary self-reset push buttons? Do the servos move when I press on the button and reset to original position as I release the button? Does it work like that or does it only work with toggle switches?

[@amolpatil9504]

Hello Kendin-Yap, I like this video can you please let me know voltage of 100uf and 10uf capacitor used in transmitter? Also capacitor used in reciver?

[@Kendin-Yap]

16V or above

[@amolpatil9504]

@@Kendin-Yap Thanks

[@bmangnote]

Thank you @kendinYap

[@hi.IJOE8]

can you make a fastest rc plane , yes this is challenge for you 👋🏻