How To Make A DC Inverter 12V To 220V [300W] (Part-4)

[@Electronic_For_You]

Circuit diagram drive.google.com/file/d/1qAoxu7oTpT1uVIo4olR5yUQLeavA-BDO/view?usp=drivesdk

[@kalashnikov_47z]

Very nice 👌🏻

[@Electronic_For_You]

Thanks

[@AbdulRahman-en3ow]

connecting first pin 5 and then pin 6 to 0.1 ohm 5w resistor on the positive side of output ? and in case of feedback for dual voltage (-/ + 35v) what should be done?

[@Electronic_For_You]

I don't know for + and - rail But I Know that current feedback will go to 0.1ohm resistance to ground Try using the SG3525 module directly because this module is specially for inverter

[@AbdulRahman-en3ow]

so pin 5 and pin 6 should be at ground (center tap of transformer), does it matter if pin 5 or pin 6 is first ? because it is PC817 thank you

[@AbdulRahman-en3ow]

without feedback (pin 8) will it work or the voltage at the output would increase or decrease on load ?

[@Electronic_For_You]

You can follow the diagram P-5 is First Without feedback the voltage should be increased to maximum level no specific value

[@AbdulRahman-en3ow]

so it is important for pin 5 to be first and without feedback it will mostly depend upon the winding of the transformer and frequency of sg3525? thanks

[@16BITMEME]

Nice work

[@Electronic_For_You]

Thanks

[@macdellsaludario8185]

how about to modify the transformer to +-50 for amplifier..

[@Electronic_For_You]

Thats not easy to tell here , You need to rewind the transformer for 50-0-50 V and output capacitors many more

[@macdellsaludario8185]

@@Electronic_For_You please make the video .. step by step .. thank you

[@Kichdiensinchuan]

Cảm ơn anh nhờ có video này mà tôi giải quyết dc vấn đề bấy nâu nay thắc mắc vì hiểu biết có giới hạn Chúc anh nhiều sức khoẻ Nhân tiện anh có thể cho toii biết phản hồi chân 8 ở mức 380v cần điện trở mấy omh ạ cảm ơn anh!!!

[@Electronic_For_You]

Hi Nice to hear that your problem is solved, and i do not recommend using a resistor , Use multiple Zener diodes to Get more stable voltage

[@Kichdiensinchuan]

Vâng rất cảm ơn anh tôi đã làm và đã thành công Điện ra rất ổn định Cảm ơn rất nhiều

[@Electronic_For_You]

You are welcome

[@Kichdiensinchuan]

❤

[@be4885]

It is a Dc12v to Dc 380v 30-60khz 600w converter it is suitable for projector bulb ballast or class D high voltage amplifier

[@Electronic_For_You]

Yes Output is DC , and can be used in many applications

[@tiagosousa5341]

Pino 7 conectado aonde ? Você sabe a função dele?

[@Electronic_For_You]

There are more parts of this video, you can watch

[@dipjyotibhattacharyya7296]

Sir,at first we connect pin 5 directly to the ground,then we should also connect the no 6 pin through 0.1ohm resistor to ground.. Now my question is..that my understanding is right or wrong.. Hope u will response soon👍

[@Electronic_For_You]

The current protection pin goes to the transistor ground then it goes through 0.1 or 0.05 ohm resistor to Main - Ground

[@triphetchannel]

Is there a complete connection circuit?

[@Electronic_For_You]

In description

[@MDAsif-jj5lu]

I need it...❤❤❤

[@Electronic_For_You]

Ok 😊

[@mrpro7737]

good project i was making one but it failed 😢

[@Electronic_For_You]

What failed? MOSFETs?

[@sagorrana2051]

now need h bridge

[@Electronic_For_You]

Yeas I don't have enough resources. I'll make Pure sine wave H Bridge

[@sagorrana2051]

@@Electronic_For_You your country ?

[@Electronic_For_You]

Bangladesh