Рет қаралды 69,384
toolsreview.us/ Series Parallel Testing Board
How to Make Electric series board for testing electric product
How To Make An Electrical Series Testing Board
What is series lamp test?
A series test lamp is a way that electricians would test or find a “short circuit” somewhere in a residential building. ... These same principles can be used to locate “high amperage drawing” devices in any circuit, just not as conveniently as screwing a light bulb into the fuse socket.
Visit My website for Electrical Jobs,Smart Home Automation Products & Systems"Diagram"
Watching More Most viewed Videos
star delta connection without motor !Use incandescent light bulb STAR DELTA Starter
• star delta connection ...
three phase dol starter Control overload Indicator Power Wiring diagram
• three phase dol starte...
3 phase DB main Power cable termination
• 3 phase DB main Power ...
star delta starter control circuit diagram ! star delta connection
• star delta starter con...
Electrical house wiring 3 gang switch wiring diagram
• Electrical house wirin...
Single Phase split AC indoor outdoor wiring diagram RYB ELECTRICAL
• Single Phase split AC ...
Star delta starter power circuit wiring diagram
• Star delta starter po...
singele phase DB wiring diagram single phase meter wiring diagram energy meter and MCB board
• singele phase DB wirin...
Reverse Forward DOL Starter Power and control Wiring
• Reverse Forward DOL St...
ring socket wiring diagram electrical house waring
• ring socket wiring dia...
two way light switch wiring diagram
• two way light switch w...
emergency light switch wiring diagram!
• emergency light switch...
cable glanding and termination low voltage switchgear
• cable glanding and ter...
STAR DELTA STARTER REVERSE FORWARD POWER WIRING CONNECTION
• STAR DELTA STARTER REV...
Low Voltage Switchgear
• Low Voltage Switchgear
How to Install cable tray Practical Skills
• How to Install cable ...
LCP lighting control panel using contactor and relay
• LCP lighting control p...
tube light circuit wiring diagram
• tube light circuit wir...
window ac wiring connection diagram RYB ELECTRICAL
• window ac wiring conne...
FORWARD REVERSE STAR DELTA STARTER CONTROL WIRING CONNECTION DIAGRAM
• FORWARD REVERSE STAR D...
3 PHASE DISTRIBUTION BOARD WIRING DIAGRAM
• 3 PHASE DISTRIBUTION B...
ELECTRICAL SWITCH BOARD WIRING DIAGRAM ! DIY HOUSE WIRING
• ELECTRICAL SWITCH BOAR...
11 kv Switchgear view
• 11 kv Switchgear view
Door Bell Wiring multiple switch and series lamp
• Door Bell Wiring multi...
House Wiring Electrical Main Board
• House Wiring Electric...
power socket installation and power socket outlet connection
• power socket installat...
THREE PHASE DOL STARTER CONTROL AND POWER WIRING DIAGRAM REVERSE FORWARD WITH LIMIT SWITCH
• THREE PHASE DOL STARTE...
Electrician Hand tools part 1
• Electrician Hand tools...
THREE PHASE ENERGY METER CONNECTION WIRING DIAGRAM- METER BOARD
• THREE PHASE ENERGY MET...
intermediate switch/3 way switch connection wiring diagram
• intermediate switch/3...
How to Make AC to DC converter at Home
• How to Make AC to DC c...
fan connection with regulator Wiring Diagram
• fan connection with re...
Proper Joint Of Electric Wire Three Different Types Of Electrical Joints
• Proper Joint Of Electr...
A series test lamp is a way that electricians would test or find a “short circuit” somewhere in a residential building. Back when homes used “screw in fuses,” that had the same thread pattern as a light bulb (known as an Edison Thread), if one circuit in a house was repeatedly blowing fuses, the electrician would remove all loads from that circuit by unplugging all appliances and turning off all of the room switches in that circuit, remove the blown fuse and replace it with a regular high wattage light bulb rated for the house’s voltage (117V in USA). If the lamp glowed at all, it meant that there was load (less than infinite resistance) in the house wiring. If it did not light up at all, the electrician would go around turning switches on in that circuit to see which “switched branch of the circuit” had a partial short (60 ohms) or a dead short (0 ohms). If the series test lamp burned very dimly, it meant that the switched circuit had a small enough load that it would not blow the fuse. After checking the switched branches of the circuit, he would start plugging in appliances commonly used on that circuit. Whichever appliance caused his light in the fuse socket to burn brightly was the offending appliance that had a short in it.
These same principles can be used to locate “high amperage drawing” devices in any circuit, just not as conveniently as screwing a light bulb into the fuse socket.