How to make kumiko 若い建具職人が組子細工を作ってみた その3 Japanese craftsmanship "Kumiko" no.3

[@SIMADA1984]

その2が何故か見れない。ともあれ素晴らしー

[@pisspissgoo]

ご視聴ありがとうございます。

[@harrymeijer393]

Very beautifull, thank you very much

[@joshuachen7001]

What a wonderful job! you are real craftsman!

[@pisspissgoo]

Thank you very much. I am still a beginner, but I will continue to do my best in the future.

[@timberline181]

「麻の葉」ですか・・すごい技術ですね。・・私、釣り好きです。シーズンオフの今、木工に取り組んでます。エサ箱とか、小物ですが。まず、材料を９０度に切り出すことすらできません。

[@pisspissgoo]

ありがとうございます。ＤＩＹの手鋸で材料を正確に９０度に切り出す事はまず不可能だと思います。実は本職でもかなりの難易度ですよ。そこで、厚みのある定規を自作なさって、それに鋸を当てて切り出すと、だいたい上手くいくと思います。参考になさってください。

[@oakidmon]

정말 대단하네요 장인의 손길이 느껴 집니다!!!

[@pisspissgoo]

감사합니다.

[@emilflognoid1532]

But Doc, all the best stuff is made in Japan!

[@pisspissgoo]

Thank you very much. Japanese technology is wonderful. I am happy to be born in Japan and to do such work.

[@katherinefuenzalida4007]

Thank you

[@pisspissgoo]

Thank you very much for me.

[@balak2992]

It is great! Superb craftsmanship! What wood is this?

[@pisspissgoo]

thank you for your comment. The wood used is "Hinoki" in Japan.

[@pisspissgoo]

nabiさん。thank you!!

[@rudyvanparys2678]

kichi0 japanse lusters

[@MrFlyingPanda]

superbe! thank you

[@pisspissgoo]

Thank you very much.

[@nightowl5091]

接着剤無しか！すっげえ

[@pisspissgoo]

ありがとうございます。最終的には接着剤で完全固定するのですが、接着剤無しでも外れないように作るのがキモです。

[@FrankDreban1]

How do you stop the hand plane from cutting into the jig bevel face?

[@pisspissgoo]

It is good to shave a little so that the cutting edge does not hit the jig.

[@FrankDreban1]

Thank you for your reply. I'm still unsure how I could use the jig to guide my cut angle and not cut the jig at the same time.

[@MarkSchreiber84]

The jig is made from a hardwood and the end grain is very tough. Moreover, when planing the little kumiko, you use a light touch, just enough to cut the soft wood but not enough to mar the face of the jig. Very similar to a razor when you shave. The hair is cot but not the skin. Mark

[@pisspissgoo]

thank you for your comment. In my case, I just dropped the tip of the jig to a slightly larger angle. Then, it can not be scraped beyond that angle. In other words, it means that the angle comes out when it can not be scraped. However, a technique is required.

[@pisspissgoo]

Thank you for the supplementary comments.

[@riquealfre]

Hola! Habla español, francés o portugués? Parlez vous français ? Fala portugués ?

[@gary24752]

You did not show how you cut the notches.

[@pisspissgoo]

thank you for your comment. I'm sorry I did not show a notch. However, it is important to make a work by trial and error on your own. Thank you.