how to make led chaser with 4017 ic

[@pauloinventostube7533]

can you use 3v relays instead of the led?

[@opeyemiagbeniyi]

Where did the white wire connected to pin 15 of the IC went to

[@BillionGear]

Just take that wire near A.C. plug or switch board (do not connect) take that wire near 3cm of A.C. plug or switch board. Thankyou for interest -BILLION GEAR.

[@pauloinventostube7533]

It was top 👍👈🤝

[@hypnoticatrance]

did you know that we have some PCB to make it. And maybe you should clean your solder tool to get better soldering... what you do is not soldering, it is more like clue.

[@ninomandal181]

can I use 12 volt power supply?

[@BillionGear]

You can use between 9 to 12V

[@ninomandal181]

@@BillionGear thanks for your kind reply 😊 I will make it for my brother in diwali . Hope you will be a great youtuber in future.

[@BillionGear]

Thankyu so much 😉

[@bmcgorakhpur5787]

What was role of wire on 14th pin?

[@BillionGear]

Its a clock input pin - when pin 14 gets pulse ,then that bunch of led will become in motion and for that pulse we have to connect pin 14 near a.c. line switch board and it makes led in motion which we called as led chaser. 📍TAKE THE PIN 14 WIRE SLIGHTLY NEAR A.C. LINE SWITCH BOARD AND THEN YOUR LED CHASER WILL WORK. -Billion Gear

[@bmcgorakhpur5787]

Yes it's working but it's working through my hands too, little distance its catching some body signal. But IC point 3 and 2 are (led 1 and 2) not working. Thanks for sharing nice video 👍

[@engineeringstuffbyhazik736]

Should we have to connect pin 14 with direct AC?? Please rply

[@BillionGear]

No not direct put that pin 14 wire near any AC power supply and when you put near AC supply so led chaser will works 👍

[@engineeringstuffbyhazik736]

@@BillionGear TQVM bro can u tell me how i connect 12 leds

[@BillionGear]

Connect all leds negative pin together and positive to ic , as shown in video .

[@engineeringstuffbyhazik736]

@@BillionGear but bro which pins of ic should i connect 11 and 12 leds

[@BillionGear]

Sorry bro You can only use 10 led

[@sdevi945]

Can i do it on breadboard with same process, plz tell me or make a vedio of it " how to make a led chaser on breadboard "

[@BillionGear]

Yes you can make led chaser on breadboard.

[@djnik9371]

3 no led is not working

[@BillionGear]

Sorry , in video led is not working because that wire is disconnected. But it 100% works , so you can try to make it Thanks for intrest .

[@ninomandal181]

Bro... What if we use 220 ohm resistor insted of 1k resistor.... Will it work on 12volt dc? Edit:- I will make it for diwali... Please reply.

[@BillionGear]

No bro use 1k resistor , and this circuit will only work between 9 to 12V ,

[@ninomandal181]

@@BillionGear ok... Thanks... And can you please tell why should we take the pin 14 wire near any ac current?

[@BillionGear]

​@@ninomandal181 I WILL NOT LIE , I DONT KNOW THAT WHY WE TAKE BUT I KNOW THAT IT ONLY WORKS AFTER PUTING THAT WIRE NEAR TO AC SOURCE .

[@kalyangautam7345]

I need only 4 channel what to do ? I tried but there is long gap

[@BillionGear]

For 4 channel led chaser there will be little change in circuit and ic will be NE555.

[@kalyangautam7345]

@@BillionGear will you tell me what is that little change?

[@ConsciousAtoms]

@@kalyangautam7345 You connect the "4" output (pin 10) of the 4017 IC to reset (pin 15). That way, it will cycle from 3 back to 0.

[@kalyangautam7345]

@@ConsciousAtoms thanks my friend

[@FenilParikh-qu7kp]

Awsome video dude Keep it up ❤❤❤

[@BillionGear]

Thanks for interest

[@hobielektro]

Mantap dan keren 😎😎😎😎😎

[@BillionGear]

Keren banget

[@FIXDIY]

Nice ..

[@BillionGear]

Thanks 😊

[@knowledgevideohemantmahara4257]

BAI APKA VIDEO ACHA HAI LEKIN APKE KAM ME BILKUL BHI SAFAI NAHI HAI JO BAHOT JARURI HAI

[@BillionGear]

Billion Gear apologize for that , Hamne kaafi sudhar kiya hai apne kam me To agar aap chahe to dekhsakte hai latest videos.

[@ajiththokkot887]

Where is the clock

[@krishgoenka1440]

last video ka lnput nahi samjha pls dikhay

[@BillionGear]

Iss video ka input Samaj nai aaya kya ?

[@skelectronicallwork]

5 volt ऑपरेट hogi

[@BillionGear]

Yes , agar na chale to fir 6V use karna 👍

[@SriLankanBrassBandMusic]

This is not working

[@aayushshah1949]

If you follow proper instructions in video , then it works ,i am telling you this because i made it with the help of this video and it works ..

[@bmcgorakhpur5787]

Yes I also tested it's not working. How to connect ac wires not instructed.

[@allinone-pg1vj]

10 led keliye 1 ic?kuch kam nahi he kya...

[@BillionGear]

no aap try karke dekh lo it 💯% works Thanks for interest 😇

[@BillionGear]

Minimum 10 led is necessary to run the circuit

[@AaaaMmm-jg6lf]

شرح ناقص وغير واضح

[@BillionGear]

For that watch video again and read the titles shown in video.

[@mccreation136]

আর তুই ওর সাথে 555 Pulce ic use কর।

[@BillionGear]

Sorry sir i can't understand your language Please write in english

[@ninomandal181]

@@BillionGear he is telling you to use 555 ic. I understand that language so.. I translated it.

[@BillionGear]

Thanks Nino Mandal

[@BillionGear]

So It will be another circuit , dont worry that video will coming soon 😉

[@ninomandal181]

@@BillionGear I am glad that it helped you.

[@jantonio0099]

welds so ugly poorly made

[@BillionGear]

As possible as i am improving my work.