HOW TO MAKE LONG RADIUS 90 DEGREE OF A CABLE TRAY W/ 4 BENDS ACCURATE TO SUPPORT AND JOINTS

How to bend 22.5 degree of cable tray 3 layer with the same distance and gap • HOW TO BEND 22.5 DEGRE...
How to bend 90 degree of cable tray 3 line with the same distance :// • HOW TO BEND 90 DEGREE ...
Different sizes of cable tray what is the travel tips and ideas
• DIFFERENT SIZES OF CAB...
Tips how to bend cable tray using x.80 formula any sizes of cable tray • TIPS HOW TO BEND CABLE...
How to bend cable tray 2 90degree with out cut accurate support to support horizontal line • HOW TO BEND CABLE TRAY...
How to bend 90 degree ang 45 degree of cable tray using 3 basic formula • HOW TO BEND 90 DEGREE ...
How to bend a cable tray with same distance • HOW TO BEND A CABLE TR...
How to make long raduis 90 degree o a cable tray with 4 bend accurate to support and joint • HOW TO MAKE LONG RADI...
How to bend 45 degree of cable tray using 1.414 formula / tagalog • HOW TO BEND 45 DEGREE ...
How to bend 90 degree of cable tray accurate to joint and support with 22.5 degree offset • HOW TO BEND 90 DEGREE ...
Cable tray u type bend accurate to support to support • CABLE TRAY U-TYPE BEND...
How to bend a cable tray bridge type • HOW TO BEND A CABLE T...
How to bend 11.25 degree of cable tray using x0.80 formula
• HOW TO BEND 11.25 DEGR...
thanks for watching and godbless:

[@randyloyoba3912]

galing idol thanks for sharing malaking bahay po yan

[@rmascarinas47]

ang galing mo kabayan...

[@jaybulaybulay8436]

Same tayo ng Formula boss🙂Good Job po.

[@hukombitaytv1976]

ang galing mo talaga master.

[@raffyosias764]

Salamat boss si mga vedio mo

[@luisfer7042]

Despejo todas mis dudas. Muchas gracias. 👌🏻

[@roelnarbuada6078]

Buenaswerte amigo

[@romeitaly7131]

Formula for radius = Actual Length - Your Travel Actual length is 25cm, but how to find "Your Travel" ?? is 5cm, 5cm, 5cm = 15cm just an example?? I hope you can explain it, please....thank you

[@maythemilsaballero9642]

Yang travel mo ay ikaw ang mag ddecide kung ilang cm ang travel mo. Yung karaniwan ninyong ginagamit sa site. Halimbawa gusto mo ng 10cm tapos 3 bend = 30cm na yun. So 30cm ngayon ang i minus mo sa distance mg support papunta doon sa isang gilid ng support.

[@seandreimedina1252]

master pano po pag 400x150 tapos 3 cuts or 3 cuts.ano po traveler?.salamat po

[@RBDboyvlog799]

salamat boss God bless

[@oledz9650]

Kung 3 vcut lang po sir ? Ilang mm lang po i cut sa tray

[@edgarpachecomarcano]

I congratulate him on the videos with very good information. But in none of the videos has it indicated how much distance should be left to join one tray with another, in this example it indicates that from the last tray to the curve there is a distance of 250 mm or 25 cm, let me explain, the tray To make the curve I cut it exactly to 250 mm or 25 cm, or I must leave a margin already tabulated, thank you. Lo felicito los videos con muy buena información. Pero en ninguno de los videos a indicado cuanto es la distancia que se debe dejar para unir una bandeja con otra, en este ejemplo indica que desde la ultima bandeja hasta la curva existe una distancia de 250 mm o 25 cm, me explico, la bandeja a realizarle la curva la corto exactamente a 250 mm o 25 cm, o debo dejarle un margen ya tabulado, gracias.

[@jub.tv123]

I think youre not understand because I explain in tagalog language but anyway thanks for watching my video good luck what you are doing..

[@usmanarif4438]

Nice

[@renatoreyes9216]

Halimbawa 30cm...ung tray...anu pwd gawin travel

[@renatoreyes9216]

Paanu poh makuha kong ilan ang travel

[@pinoymixmartialart4232]

I dol pag 2 vcut isa lang travil e minos mo tama ba i dol?

[@jamescabs1989]

Ok boss thanks @jovan cabs to

[@eidulqamar3170]

Pary 30 digree v cat farmula tel

[@dencio8646]

Pag 100x100 same lang din ba

[@jub.tv123]

Opo

[@alvinjamz1249]

Parihu Din Poh ba Ang pag kuha NG cable tray n cable ladder example.100mm Yung kuha 80 di Poh ba?

[@jub.tv123]

Oo sir

[@leoaugost956]

d

[@pinoymixmartialart4232]

I dol pag 10cm cable tray mo 10cm minus mo tama ba? ?

[@katelynskitchen-ph2074]

i dol pano.naman sa dalawang bikat tatama ba

[@jub.tv123]

May video ako dyan sa dalawanh v-cut sir watch nio nalanh po...

[@nagendarsingh3437]

Hind me

[@SujeetKumar-gr8eu]

Pls speak in hindi

[@jub.tv123]

Okey nextime ill speak hindi..namasti, kiyali, tiki,

[@akbarbasha3392]

Bro English pls

[@pastor8423]

Wala maintindihan ang Gulo