How to make LOW Level and FULL Level Alarm with Level Indicator

[@Piotr-yc8gz]

Dziękujemy.

[@anuragprojects]

Welcome

[@ALMAMUN-uo5yf]

Aponar video golo oneck excellent sar .thanko

[@paulojuniorlatibo1160]

This is the perfect project that i was looking for. Thank you.

[@Aurelius7777]

Nice stuff. Thanks for teaching.

[@anuragprojects]

My pleasure!

[@naoufelmami5107]

Worked for me thx a lot

[@kingslyroland4598]

Haw Is that coper wire being switch with water?

[@devadasond9213]

Excellent menceaning for the nameof the elements. Thank you

[@varietieschannel3821]

Thanks for the great project.❤ 5 v Does it work with four floors of the house?

[@kartalveat]

Su seviyesi yükseldikce alt seviye led'leri sönmeli.Tam dolu halde tüm ledlerin yanması saçma.Ayrıca gereksiz güç tüketimi.Olması gereken hangi sevideyse sadece o seviyeye ait led yanmalı. Fakat gene basit ve bu haliyle bile işe yarar olduğu için teşekkür ederim. Bence ,yukarıdaki uyarılarıma göre devrede değişiklik yapabilirseniz daha uygun olur.

[@AberdeenshireBeasties]

Interesting video but I went the route of building an ultrasonic based level, much easier and does not need to be in contact with the fluid

[@mukundlk]

If you are using DC to sense the water, it will not work long. Oxidation of water sensors will happen. Whole system will need severe maintenance quite frequently.

[@لاققف]

ل ٤٥ عن ت عَ نور

[@feku_kejruddin_raul]

Yeah he should go with 220 volt AC😂😂😂

[@mukundlk]

@@feku_kejruddin_raul no dear. He should use 440v 3 phase and take you as assistant for RnD..😂😂

[@sonyjosephsunsoftrecording5639]

❤❤@@لاققف

[@alinamkrtchyan3963]

Afffffffr

[@ramgarhia-k9h]

Sir include the pump switching option also👌👌🙏

[@moeensehr780]

Good sir, 680 ohm ki jagha 330ohm bhi laga saktay hain kya

[@sylvianeta]

I would like to know what a diference makes because I have 330ohm and 470ohms😮

[@lynilthomas]

Can u pls tell which wire u used as that thick wire to solder other components?

[@dcmart8481]

Good job😊

[@linushet107]

nice and simple

[@Harry001by7]

Electrolysis is good for daily usage water ?. And what about electrodes by the electrolysis ?

[@valtersouzaribeiro761]

Boa tarde parabens muito bom excelente projeto

[@anuragprojects]

Thank you 😊

[@pmkarunarathna3681]

👍👍

[@黄蟮]

​@@anuragprojects It's a three-story building, can the water tower be connected to the first floor?

[@pankajkumarroy3461]

Sir battery kitne bolt ka ujj kare...

[@tahiralishahbukhari7141]

Shabash Bache

[@anuragprojects]

Thanks

[@andayashon2069]

what is the purpose of the 1N4007 Diode?

[@suryaprakash3156]

Bhai ghr k liye tanki k liye bnana h to usi AC current de ya mobile charger ka use. Karna padega

[@anuragprojects]

Yes, app Mobile charger ka use kar sakte hai....aur koi bhi 5v - 12v ka power supply use kr sakte ho.... Thanks for watching.

[@rajendrapal505]

good job

[@rahimtullahbijapure8785]

Anurag I am retired Superintending Engineer Design (CIVIL) I am having interest Electronics also. Your circuit appears has defects i.e. when tank is empty Buzzer starts buzzing and rremains buzzing even after filling completely fills , infact buzzer should not while filling tank 20% ....till 90% .can you explain me what circuit has some error?

[@baburaobagade6941]

Technically circuit is correct, may be wire connection not proper, from bottom 3rd transistor shall be connected to top level sensor . Bottom transistor to 2 nd lowest sensor.

[@robertneill3057]

Food Grade Epoxy adesive used if doing drinking water. A more complex alternating signal probe setup would use op-amps and possibly the 4000 CMOS logic. An actual pcb/protoboard will be used also.

[@ursopolar6535]

Well done!

[@suryaprakash3156]

Sir kisi video me dekha tha mene usme led k baad 1 k resistor or transistor k baad 10 k resistor ka use kiya h to wo sahi h kya karna

[@AndyUK-Corrival]

Would this,work for diesel tanks?

[@anuragprojects]

No

[@mahfooz7747]

Thank you for sharing your knowledge

[@igeorgantzas]

works with diesel oil?

[@anuragprojects]

No

[@rahul47863]

😂Empty buzzer beep is awesome Can i use 1k resistor in this for 9v battery current 😊

[@anuragprojects]

Yes

[@rabinbaruah4375]

I want.duch.a water.level.meter. where shall get ?

[@sudhir1909]

Like your project. Thank you so much 680-ohm Resistor -> How many warts? 1K Resistor -> How many warts?

[@anuragprojects]

All Resistors are 0.25 Watt (1/4w) Thanks for watching my videos.

[@kennmossman8701]

see your doctor for warts

[@volselectronics4709]

good video good work

[@anuragprojects]

Many many thanks

[@imkrugger1741]

If I'd like to make this in a PCB, what components should I use?

[@RAJSHARMA-wr6go]

Is m empty ke liye push batan laga sakte h

[@anuragprojects]

Yes

[@DansonMathew]

Thanks

[@anuragprojects]

Welcome

[@annel30626]

Wowww nice idea.thank you bro

[@anuragprojects]

Thanks and Most Welcome 😁

[@Petukbhai838]

WONDERFUL!

[@anuragprojects]

Thanks

[@suryaprakash3156]

Sir ism 680 ki jgha 220 ohm ka resistor lagaye to ye work karega k ni

[@anuragprojects]

220 ohm se LED kharb ho jayega...aap 560 ohm - 1k use kijeye.... Thanks for watching.

[@sridharkrishnappanavanerth3388]

Circuit diagram in thumbnail is different from what you have shown in demo. Will that circuit diagram also work.

[@Luffy-888]

Can we use any type of ohm resistor(220 ohm resistor) plz reply

[@anuragprojects]

Yes, Thank you for watching my videos.

[@Luffy-888]

@@anuragprojects mane bina resistor ka banaya aur wo work bhi kar raha hai

[@MeghnaSolarPower]

is it work with 500 liter tank?

[@anuragprojects]

Yes

[@coinstatsset6555]

เจาะให้รั่วไง เอาแค่ หมดก็เปิด เต็มก็ปิด การเพิ่มมนแต่ละดับสิ้นเปลือง sensor ไม่ถูกตรงไหน ครับ

[@JomonJoseph-b4u]

Is this circuit adequate for a six meter deep tank? If not, what changes should be made?

[@prayalankarsharma2738]

How to deal with ionic erosion in water dipped leads

[@alaska_channel21]

Very good 👍🏻👍🏻👍🏻👍🏻

[@anuragprojects]

Thanks 😊

[@Aswinsreedhar-eg6hs]

1indicator circuit fit cheyamo

[@jumbo999614]

Can anyone explain the red LED and buzzer that activate when too less water in the tank? I still don't understand how it works. Why there is extra transistor and resistor at the bottom of the circuit? where the bottle is empty, what causes red led and buzzer to turn on? and water level goes above 25%, what make red led and buzzer to turn off?

[@muhammadsaeedkhan1803]

There is finish water in the TANK

[@rajkumaraw]

See the connection making process 5:39

[@shrikantgenius]

good project bro simple and sower i appreciated.

[@anuragprojects]

Thanks sir

[@electproject]

GOOD PROJECT EVER

[@anuragprojects]

Thanks ☺️

[@ketikcoding]

What is the name of the tool that is put in water?

[@anuragprojects]

These are copper wires. Thanks for watching

[@fareszmaineberkok]

Thank You it's very good very nice ......100/100

[@anuragprojects]

Most welcome 😊

[@paulovictordsantos]

Is safe to use in a real gas tank?

[@anuragprojects]

Not safe for gas tank

[@Aimusical7826]

Bc 547 transisters are NPN or PNP type ? Please guide

[@Ecetamil]

BC 547 is npn only

[@anuragprojects]

BC547 is NPN transistor. Thanks for watching

[@sridharkrishnappanavanerth3388]

You should have explained with the circuit diagram.

[@nirwanhamid2719]

If you use a 9v battery voltage and the buzzer is still 5v, is that possible?

[@ravindraadapa2952]

You have to improve this to the next level and try to add big speaker l

[@moeensehr780]

Sir i have used 650ohm resistor its not working onyl buzzer is working rest led is not working

[@julio-pl7nn]

Que tipo de led son? Tamaño y voltaje

[@anuragprojects]

10mA 3v 5mm LED. Thanks for Watching my videos 😊

[@amitvinayaka]

Resistor ki watt kya hai

[@astronic4522]

Nice project brothers

[@anuragprojects]

Thank you so much...bro...😊

[@ujangahmad01]

thank you very much, this is very helpful❤

[@TulsavatiMandavi]

Brother 680 ohm resistor qouter ohms ki off ohms bro

[@RAJSHARMA-wr6go]

Kese lagaye 555 ic ko is m

[@sandeepnipuna4303]

👌👌👌

[@sincerepublic]

What was the voltage?

[@anuragprojects]

If you replace 5v buzzer with 12v buzzer. so you can use 5v, 9v, 12v power supply. Thanks for watching

[@jfmendonca9200]

Este sistema funciona em 12vdc?

[@anuragprojects]

You can replace 5v Buzzer with 12v Buzzer. Then you can give 12v. Thanks for Watching my videos 😊

[@jfmendonca9200]

@@anuragprojects thank

[@m.arsyaelnathan9606]

Mantaaaap

[@tzant]

if you make such thing for a car engine oil level you'd get a Nobel!

[@diwassubba5495]

It won’t work well coz, while running slanted upward or downward road the fuel also align with the level , so the indicator gives the false report.

[@banjadenisvictor3338]

Modern cars already have this

[@nandchawla4486]

Superb job.... Solid

[@anuragprojects]

Thank you so much

[@RixtronixLAB]

Nice video, thanks :)

[@anuragprojects]

Most welcome and Thanks for watching my videos 😊

[@armanmalik3749]

Sir 5v input power kaise de please help

[@anuragprojects]

Hi, 5v 2a adapter use kijiye. Thanks for watching 😊

[@Aqeel.M]

Like your project. Can I buy online. Please recommend and link as well

[@rachidbelhenini1708]

Thank you for video.

[@anuragprojects]

Most welcome 😁

[@contrivance1982]

Can I use 9v or 12v ? If yes then should I change any components?

[@anuragprojects]

You use 12v buzzer in it, then you can give 9v or 12v. Thanks for Watching my videos 😊

[@stephaniecastro1019]

@@anuragprojects if i change the buzzer volts then i need to change the battery volts right? i tried looking for 5 volts but can't find it. I'm worried i might messed up or get shocked or something. is there anything i need to change?

[@houcineamaidi499]

GOOD WORK BROTHER

[@anuragprojects]

Thanks

[@r_b.gaming]

Awesome ❤

[@anuragprojects]

Thank you so much 😊

[@michaegi4717]

Nice prototype. For more constant brightness you should use adapted resistor values for red and blue LEDs. For those who want to build something similar for real aplication: Please be aware that you produce tiny amount of oxygen and hydrogen. You shouldnt seal the container. Be aware that the generated oxygen might react with the copper. This might not work for longer time due to corrosion and some materials might be released into water. Don't drink it or use it for plants you want to eat.

[@kennmossman8701]

and the electrodes will eventually be destroyed

[@remeshkumar8107]

Howmany volutage battery charge

[@TESTMNOKTI]

طريقة جميلة لكن ليست عملية . لا يمكنك وضع اسلاك داخل مياه صالحة للشرب هناك شئ اسمه الأكسدة ...الخ . يمكن ان تقوم بهذا لكن بطريقة اكثر صحة ويمكن استخدام مبدأ الحث او المغنطة لإعطاء الترانسزتور اشارات .

[@abumuhammad2611]

ممتاز

[@peterfitzpatrick7032]

Why does the buzzer sound at 100% ? 🤔

[@mukeshbaria1430]

Long time Kam Karta hai ye

[@simadri374]

Taar paani me dubo rahega to paani kese piyenge

[@anuragprojects]

Sir ye demo project hai...ye 5v pe work karta hai to aapko current nhi lagega...chayeto aap ultrasonic sensor ya float sensor ka use kar sakte hai...100% safe hai.... Thanks for Watching 😊

[@bazookamobile7801]

Verry good

[@zaibgraphics7294]

Transistor pnp hay npn

[@pradeepmahendrasemage4043]

Nice.

[@anuragprojects]

Thanks 😊

[@พีโมบาย-ฅ1ฑ]

ขอให้แสดงเนภาษาไทยด้วยครับ

[@edsonlutepo2240]

Awesome I like it

[@SamiUllah-kb3wr]

Nice

[@anuragprojects]

Thanks bro...

[@hihohiho57]

دەست خۆش

[@anuragprojects]

Thanks 😊

[@saratrana1174]

Sir in India सर इधर कौन है इंडिया रवि सर जी

[@misNudosyCuerdas]

Excelente

[@anuragprojects]

Thanks

[@ashwnainaman]

Restant ka +- bahi bato Not working properly

[@TulsavatiMandavi]

Brother please respond

[@lindsayferris1073]

How can I make a wireless version of this?

[@anuragprojects]

Yes, Please watch this video kzbin.info/www/bejne/p6WpqKKljM13gs0

[@armanmalik3749]

Mobile charger se work nhi kar raha h

[@Shots_Dimension]

I made it perfect but it is not working

[@narenka5618]

Good

[@anuragprojects]

Thanks

[@dumindapriyadarsha3196]

Grateful

[@SvenRino]

Ага .. а почему не 220 .. 380 .. или 1000 вольт через воду не пропустить