How to make MIST MAKER at home | DIY mist maker

[@sam_d999]

I also learnt it from Scott...he is genius

[@EDISON_SCIENCE_CORNER]

True that

[@LEO-xo9cz]

Great Scott? Maybe you have an answer. I want to build a dry run protector to shut it off when there is no water.

[@sam_d999]

@@LEO-xo9cz you can achieve it in different ways...using controller and sensors or using the same 555 timer ic u r using to make the mist maker. Watch carefully that the pin 4 of the ic(reset pin) is connected to the +ve terminal that turns on the ic. If it is zero or grounded your ic will not turn on. So take two wires and remove the outer coating and insert the metal wires deep inside the water container to the level that satisfies you where you placed the disc. Now connect one wire with the +ve terminal of the battery and other wire to the pin4(or the reset pin) of the 555 timer ic. That's it....if water goes below the level your ic will shut itself off automatically. But the problem is you will lose a small fraction of power as your ic is connected when there is no water. So better connect the gnd wire of the circuit with the gnd terminal of the battery......and then connect one wire (remember the 2 wires you put inside the water container where you placed your piezoelectric disc) with the +ve terminal of the battery and other wire with the whole circuit's +ve input. This method will be very simple and will help to save power too.

[@EDISON_SCIENCE_CORNER]

Yes 🥰🥰

[@Cy-by]

learned*

[@iranfreedom12]

use irlz44n (or IRL2203N, go for lower rds as we switching in very high frequency) for mosfet, use tc4427 for gate drive. add snubber circuit and you can go up to 24 volt(use 12 volt regulator for 555 and tc4427 vcc and throw some filterig cap around) and you will have have much cooler mosfet. you should have around 80 miliamp usage at 22 to 24 volt. snubber circuit 10 nano farad ceramic cap and 40 to 60 ohm 1 watt resistor.

[@EDISON_SCIENCE_CORNER]

Great

[@HerrBjork]

Great video! I hope to be able to implement something like this in place of a carburettor or injection system in a car, as such a fine mist of fuel has a potential to improve efficiency, esp. for ethanol and other fuels that unlike gasoline don't vapourise at room temperature

[@EDISON_SCIENCE_CORNER]

❤️

[@HerrBjork]

@@side-room-21 Not yet but I've done some minor theoretical work on it

[@EDISON_SCIENCE_CORNER]

Eh..

[@robinsharma]

Sir one question please do reply I have got Pizeoelectric Humidifier sensor and now I need to create power circuit board for it to work or If I directly connect it to power it will work? Please reply ir it's urgent

[@EDISON_SCIENCE_CORNER]

I didn't understood

[@samuelpauls2103]

Nah

[@kateashleyortega7191]

@EDISON SCUENCE CORNER, does this device have a switch were you can turn it on or off, or does it just automatically create mist once it touches water?

[@EDISON_SCIENCE_CORNER]

No switch

[@st3ve268]

Is it possible to use a ESP32-S3 for frequency instead NE555?

[@EDISON_SCIENCE_CORNER]

Yes you can

[@MrMinimum24]

Can i used piezo buzzer instead of piezo cryatal

[@EDISON_SCIENCE_CORNER]

No 😯

[@DebabrataKumarSaha]

Can I use 1.7 mhz piezo disk with this circuit?

[@EDISON_SCIENCE_CORNER]

No 113khz

[@DebabrataKumarSaha]

@@EDISON_SCIENCE_CORNER ok

[@UL7R41337H4XX0R]

Hm, nice video and all. But the circuit doesnt seem to work for me. Built it like in the schematic, and it does put out a high pitched sound when the potentiometer is at max, but when tuning up nothings happening. Any suggestions? My other try with a readymade ne555 circuit hooked up to a irfz44n just seems to catch fire, altough i can not find any problem....^^' Things working perfectly once again...

[@EDISON_SCIENCE_CORNER]

Refer to the great scott tutorial also

[@UL7R41337H4XX0R]

@@EDISON_SCIENCE_CORNER thx :)

[@melplishka5978]

Scotty’s the best lol. Nice job 👍 bud.

[@EDISON_SCIENCE_CORNER]

🔥

[@arvietuyor1872]

Hello, Can I use different inductor? I can't find similar like you have

[@EDISON_SCIENCE_CORNER]

Try with that i don't know the outcome

[@arvietuyor1872]

How about the Capacitor? Can I use ceramic or mylar?

[@Thebasicmaker]

As far as it has the same value you can use it

[@PHBUS-en4qv]

I want to use it in order to grow plants without soil (aeroponics). I don't know if it's work with this mist maker system, I will try

[@EDISON_SCIENCE_CORNER]

Try

[@Anna-tc6rz]

Hey me too! Please keep me updated if you do it! I'll drop a comment when my system gets going

[@visit402]

The mister will have to be on all day. Will the board overheat?

[@youtubevanced9838]

Is it same funtion with aquarium sterilizer like twinstar sterilizer?

[@EDISON_SCIENCE_CORNER]

I don't know sir.!

[@aaaaa-gn7me]

Do I have to change the other components if I'm using a 2 MHz piezo electric disk?

[@EDISON_SCIENCE_CORNER]

We cant generate that frequcy with ic555

[@pratyaksh4283]

Where did you get the inductor coil that you have used so how to make it?

[@EDISON_SCIENCE_CORNER]

Bought it from amazon

[@rajendrasagar4044]

Very Simple Circuit, thanks for sharing.

[@EDISON_SCIENCE_CORNER]

Thanks sir 😊

[@t.hussain6278]

Many thanks.

[@millardvp]

Can it support two piezo?

[@EDISON_SCIENCE_CORNER]

I Never checked that sir

[@millardvp]

@@EDISON_SCIENCE_CORNER thank you.

[@parveenbegum4236]

I have a question can you connect a n USB dongle in the screw in the left side

[@EDISON_SCIENCE_CORNER]

For what

[@parveenbegum4236]

@@EDISON_SCIENCE_CORNER The mist maker

[@EDISON_SCIENCE_CORNER]

I dont understand what you mean

[@cathyny83]

Thank you for the video. I have this little white cap on the end for my atomizing transducer which I intend to replace it, I'm unable to solder it on the circuit board because on the original board doesn't have that, may I know is there a way to do it?

[@EDISON_SCIENCE_CORNER]

Can you share the images. Use the social medias to share links are in the video description

[@elvinkasumovic3296]

Does the piezo element get worn out? And did you try other heavy liqueds to vaporise?

[@EDISON_SCIENCE_CORNER]

Worn out means???.... Alcohol is okay.

[@marcelinbelisle2643]

any change i could do to make it work with a 12v transformer?

[@EDISON_SCIENCE_CORNER]

Yes.

[@EDISON_SCIENCE_CORNER]

It will work on 12

[@marcelinbelisle2643]

@@EDISON_SCIENCE_CORNER nice, ty for replaying so fast

[@skyedangelo3237]

could this circuit drive multiple disks? like say a 4 or 6 head array or would we have to create a different circuit?

[@EDISON_SCIENCE_CORNER]

You have to use different drivers for that

[@skyedangelo3237]

@@EDISON_SCIENCE_CORNER I would be very interested in a video looking at that!

[@WonderfulDay-jw7wu]

hey can i build a large disc? and thick disc?

[@EDISON_SCIENCE_CORNER]

No

[@WonderfulDay-jw7wu]

@@EDISON_SCIENCE_CORNER will i did my homework and they say i can use 8 to 9mm size thick.. not sure why you say no... and they do sell them big one also. iam not sure why you say no... lol

[@WonderfulDay-jw7wu]

@@EDISON_SCIENCE_CORNER pzt5, pzt5

[@vel3185]

This project 25mm disc can use?

[@EDISON_SCIENCE_CORNER]

Use it check the frequency first

[@danieljheelan5256]

Hi, Thanks for sharing. Want to use it fo my orchids. Can you tell me if it's possible to connect several piezoelectric disc. If yes, what is the maximum number. Thanks for your update. Shiam

[@EDISON_SCIENCE_CORNER]

No

[@danieljheelan5256]

@@EDISON_SCIENCE_CORNER Thanks a lot for your update. The DC power supply cables are soldered and it rest on the water. It does not create a short circuit?

[@arvietuyor1872]

Why kind of capacitor you use here? The 10NF it is ceramic or mylar?

[@EDISON_SCIENCE_CORNER]

Type of capacitor doesn't change anything here

[@arvietuyor1872]

@@EDISON_SCIENCE_CORNER thank you very much

[@HINDUVeeBee]

Is this Disk is manufactured in India. If yes by which manufactures..

[@EDISON_SCIENCE_CORNER]

I don't know about that sir. I bought it from AliExpress

[@HINDUVeeBee]

@@EDISON_SCIENCE_CORNER Bringing materials from Ali express means Directly or indirectly financing Chinese government who uses money for our Destruction..

[@EDISON_SCIENCE_CORNER]

I bought 2 years before

[@denisdb725]

GREAT JOB. If I can find the needed parts here in the south of Portugal I go for it. Is it possible to connest more piezoelements to one board and if so what is to be used extra?

[@EDISON_SCIENCE_CORNER]

You can connect

[@denisdb725]

@@EDISON_SCIENCE_CORNER Thank you for the reply. A max amount of elements? I think I try this for aeroponics setup.

[@silverpassion3588]

Tks for the vid. May I know whats the wattage of the mist maker in your video? Just wanna know the power consumption. Can it turn on for 24 hrs without overworking the gadget or recommended to off it every night. Tks

[@EDISON_SCIENCE_CORNER]

I am not sure about is power. It will Overheat and damage 100%

[@arvietuyor1872]

Hello sir I can't find 5k variable resistor, can I use potentiometer with the same value?

[@EDISON_SCIENCE_CORNER]

Use 4.7 k

[@MrRyant081]

Modul ini hanya untuk satu piezzo , atau bisa untuk beberapa piezzo bro ? 🙏

[@EDISON_SCIENCE_CORNER]

You have to add different driver circuit for that

[@Spyah]

@@EDISON_SCIENCE_CORNER i'm also interested in building this myself for 4 discs

[@pulathisibhathiya6381]

Wow! very clean. I can build an air freshner using this. Otherwise it would cost me around 30$-100$. This costs only around 10$, probably less.

[@EDISON_SCIENCE_CORNER]

Thanks. Yes you can build this with 5-8 $

[@kinaayyung]

1. to place the component to pcb board, should we follow where place it like the video or it allowed to randomly place it?? 2. for the green thing, can we change it with usb type b? so it could connect with type b cable hope you answer it

[@EDISON_SCIENCE_CORNER]

You can place components according to your idea

[@EDISON_SCIENCE_CORNER]

Ofcourse you can replace screw terminals with any connector but you have to give 14v

[@cherylm2C6671]

Thank you for posting this video. I am going to try it and hope it helps someone. It's very hot!

[@EDISON_SCIENCE_CORNER]

Go on

[@EDISON_SCIENCE_CORNER]

Will try bro

[@EDISON_SCIENCE_CORNER]

🤩🤩🤩

[@syamasundararao3149]

Excellent description. Kudos.

[@EDISON_SCIENCE_CORNER]

Kudus

[@spiderobert]

This is really cool :P I get very dry skin and like making things with electronics; so I think I will try to make one of these. I think having it more contained would be nice, so I guess I'll be attempting to make my own humidifier.

[@EDISON_SCIENCE_CORNER]

Good luck

[@EDISON_SCIENCE_CORNER]

Go on

[@timetoplay4614]

Hey can we run this circuit on 5v supply? Plz reply

[@EDISON_SCIENCE_CORNER]

No we can't

[@timetoplay4614]

@@EDISON_SCIENCE_CORNER do you have a circuit for 5v supply? If it is can you please give me a link?

[@Learning_Politics]

Can I connect that disc directly to 5v charger?

[@EDISON_SCIENCE_CORNER]

Absolutely yes but .nothing will happen

[@muralimayhem]

where did you get the waterproof ring for the disc? Any link?

[@EDISON_SCIENCE_CORNER]

Check the discription 🥦

[@zulhakimzulkifli6040]

hi is it normal to get shock when i touch the white damper area when the device is on? cause im afraid it might have electric leak

[@EDISON_SCIENCE_CORNER]

Its is beacuse of the oscillation

[@zulhakimzulkifli6040]

@@EDISON_SCIENCE_CORNER thanks for replying. So its normal right? can i touch the water also sir?

[@EDISON_SCIENCE_CORNER]

Actually i am 100% not sure about that. I am talking about the vibrations of disc. I dont know about yor circuit ..!

[@ambalapetlover7904]

can i use ordinary pizo,,that use in multimeter

[@EDISON_SCIENCE_CORNER]

That's works on 1.7mhz we cant use in this circuit.

[@ambalapetlover7904]

thanks

[@EDISON_SCIENCE_CORNER]

Welcome

[@Ricky-y8k]

Can i oprate more than 1 disc on same circuit ?

[@EDISON_SCIENCE_CORNER]

No you have to use a separate driver for disc

[@Ricky-y8k]

@@EDISON_SCIENCE_CORNER ...sir, piezoelectric disc used in video resonate at 113Khz but at my place most of piezoelectric discs available resonate at 1.77Mhz . Sir can you pls make video on it?

[@leoaugustocwb]

Impressive dude!

[@EDISON_SCIENCE_CORNER]

Thanks buddy

[@tholitzivanvilla2570]

I see this kind of circuit from the other channel, is it normal that the MOSFET getting hot? Thanks!

[@EDISON_SCIENCE_CORNER]

Normal case

[@LuisAguilar-xd2hw]

Im new to the electronic world, is Irf z44 Mosfet and Irf z44N Mosfet the same thing?

[@EDISON_SCIENCE_CORNER]

Allmost same. You can refer the datasheet

[@siva_b_1999]

im using non waterproof piezo disc...can i insulate and use it

[@EDISON_SCIENCE_CORNER]

Its Okey to use with water

[@siva_b_1999]

@@EDISON_SCIENCE_CORNER what changes should I do to the cirucuit to increase the piezo plate count ( increasing surface area of the plate for more humidity)

[@EDISON_SCIENCE_CORNER]

You need to drive each piezo seperately

[@hugoantoniogonzalezramirez4261]

excellent video, I have a doubt in the diagram where pin 7 of the 555 is connected

[@EDISON_SCIENCE_CORNER]

Not connected

[@hugoantoniogonzalezramirez4261]

oh thanks, sorry for the inconvenience but I have another question, I already put together the circuit but the most it sounds a beep and when I put the sensor on the surface of the water the beep starts to cut off and the mosfet gets too hot

[@visit402]

I saw your comment on greatscotts video! You fixed the mosfet overheating? Can you use 5 volts to power it like the usb misters

[@EDISON_SCIENCE_CORNER]

Oh no not yet still has the problem. I don't know if it is possible with 5v

[@visit402]

@@EDISON_SCIENCE_CORNER how long can it run if it heats up? I want to humidify mushrooms

[@EDISON_SCIENCE_CORNER]

Not possible

[@visit402]

@@EDISON_SCIENCE_CORNER greatScott made me think this was possible. Why post the video and not explain the part about it not working lol

[@EDISON_SCIENCE_CORNER]

It. Is possible. I said it has some problems

[@rutuzable]

How did you find or calculate the frequency? Which equipment have you used ?

[@EDISON_SCIENCE_CORNER]

You can find that from datasheet

[@rutuzable]

@@EDISON_SCIENCE_CORNER I cant get you brother where to find the data sheet?

[@EDISON_SCIENCE_CORNER]

You can find the resonance frequency from the datasheet of disc. You can measure the 555 oscilation frequency using a CRO

[@deta3d921]

Hi how if i put this behind a small fan, can it make the air cooler ?

[@EDISON_SCIENCE_CORNER]

Nice one😍

[@aykutesen8551]

I have a 2.4mhz piezo disk, can I use it in this circuit?

[@EDISON_SCIENCE_CORNER]

No you can't

[@enzo10101]

@@EDISON_SCIENCE_CORNER what should i change to do that with 2.4Mhz disc?

[@richmartfamilar6300]

Can I use 12v power supply in this project?

[@EDISON_SCIENCE_CORNER]

Yes

[@1islam1]

🔴 What Is Islam? ⚠️ 🔴 Islam is not just another religion. 🔵 It is the same message preached by Moses, Jesus and Abraham. 🔴 Islam literally means ‘submission to God’ and it teaches us to have a direct relationship with God. 🔵 It reminds us that since God created us, no one should be worshipped except God alone. 🔴 It also teaches that God is nothing like a human being or like anything that we can imagine. 🌍 The concept of God is summarized in the Quran as: 📖 { “Say, He is God, the One. God, the Absolute. He does not give birth, nor was He born, and there is nothing like Him.”} (Quran 112:1-4)[4] 📚 🔴 Becoming a Muslim is not turning your back to Jesus. 🔵 Rather it’s going back to the original teachings of Jesus and obeying him.

[@shouminz]

Thanks for ur video. Can this method be refined into smaller bubbles? I would like to use this way to CO2 diffuser.

[@EDISON_SCIENCE_CORNER]

I dont think soo

[@youtubevanced9838]

U can try nano air stone

[@michaeljoshuamanallo1742]

Can I use a 330uh inductor instead of the 220uh??

[@EDISON_SCIENCE_CORNER]

Yes you can use.

[@marcelinbelisle2643]

Hi, i don't have an electronic/electric background an im not able to read the circuit. since i have place all the piece in de exact same place as you, could i see the sodering so i can copy the same pattern? It would be very appreciated :)

[@EDISON_SCIENCE_CORNER]

Just follow the circuit

[@marcelinbelisle2643]

Yeah well, as I said, the circuit make zero sens to me

[@marcelinbelisle2643]

Could i buy 1 on edisonsciencecornor? I could copy it if i need more in the future

[@EDISON_SCIENCE_CORNER]

You can

[@subrayabaliga8632]

Stick the transducer below the cup with arldite and get same vibration effect. Use suitable heat sink for transducer else it will burn off, in short time. It is good methodology to deliver medicine right deep into lungs . But use it judicially. It can also be used to clean rust parts. De stain clothes or as washing machine.

[@EDISON_SCIENCE_CORNER]

Thanks❤️

[@lrham]

can i just connect the ultrasonic disc mist to usb ?

[@EDISON_SCIENCE_CORNER]

Noo . Will not work

[@nitishsaini63]

can i connect more than one piezo to same circuit

[@EDISON_SCIENCE_CORNER]

No

[@kevinperies4450]

can i use a 12v battery for this?

[@EDISON_SCIENCE_CORNER]

Might be

[@jingola11]

Just another intelligent indian ❤️

[@EDISON_SCIENCE_CORNER]

😊😊😊😊

[@RODOLFO.M.S]

🙏🏼🇧🇷👍 Just subscribed to your channel. Beautiful work, you have a video showing how the Joules thief and its components work and how the electrons behave.

[@EDISON_SCIENCE_CORNER]

I made a joule thief video. But not explaining everything . But i will try 😃

[@JL-dh4ub]

Hi, hope that you can shed light on the piezo disc used in eg nano facial mist spray. Does it have any metal components that will be in contact of water? Cos i was recommended to use a metal-parts-free spray to avoid the ingredients de-stabilized by metal. Cheers😀

[@EDISON_SCIENCE_CORNER]

Thank you

[@neirenoir]

They are usually made of metal, but I think you can find ceramic compund piezoelectric discs from some vendors.

[@viralreels3014]

sir ca we say it is water vapor machine plz sir tell me ?

[@EDISON_SCIENCE_CORNER]

We cant say

[@muhamadqih]

Can i use 108khz membran??

[@EDISON_SCIENCE_CORNER]

Yes

[@sushanthchalla7595]

is the circuit required , cant i just give power directly to piezo disk?

[@EDISON_SCIENCE_CORNER]

Without the circuit we cant resonate the piezo

[@sushanthchalla7595]

@@EDISON_SCIENCE_CORNER yeah okay what is 555 timer for ?

[@EDISON_SCIENCE_CORNER]

To generate 133khz signal

[@kamanghaph3175]

Can i used 1 board and 2 mist sprayer?

[@EDISON_SCIENCE_CORNER]

Probably not

[@hyperrunner4589]

Does it gives any cooling effect?

[@EDISON_SCIENCE_CORNER]

Yes

[@tholitzivanvilla2570]

Hi! What type and exact specifications of capacitor is the yellow one. I think it's the 10nF but I don't know what type it is😅. Thanks!

[@EDISON_SCIENCE_CORNER]

Film capacitor. Any type will work

[@tholitzivanvilla2570]

@@EDISON_SCIENCE_CORNER I almost had a hard time finding that type of capacitor,😅 now I know any type will work. Thanks a lot!

[@beetelvj10]

Very descriptive vedio, must me a expert, other vedio are just a normal display of talent without assuming that other are new to this domain, so theis vedio is very helpful, every stage ,every Insteument is explained very well

[@EDISON_SCIENCE_CORNER]

Thanks

[@manishmahor6501]

Ye kese banega apki plat to plan or simply he conact kese hoga

[@EDISON_SCIENCE_CORNER]

English please

[@steveraman7619]

excellent info keep it going all the very best from germany

[@EDISON_SCIENCE_CORNER]

Thankyou from india

[@naveenkumarej]

Can i use “220uH 1/2W 0410 Color Ring Axial Lead Type Inductor” ? also will this circuit works in 12v 1A input?

[@EDISON_SCIENCE_CORNER]

I dont know about the result

[@sagaspace]

Can we connect multiple mist generator with this circuit? Like 5 to 10 mist generator

[@EDISON_SCIENCE_CORNER]

Yes but you have to use different mosfet for that

[@sagaspace]

@@EDISON_SCIENCE_CORNER which. ?

[@EDISON_SCIENCE_CORNER]

I mean if you want control another disc you have to use seperate MOSFETs driver circuit

[@sagaspace]

@@EDISON_SCIENCE_CORNER ok thanks ❤️

[@aftabbashir3586]

Can we get 113 kHz piezo electric disc from market

[@EDISON_SCIENCE_CORNER]

90% not sir

[@junelbayas7252]

@@EDISON_SCIENCE_CORNER why?

[@astro_kozuki]

This safe for aquarium?

[@EDISON_SCIENCE_CORNER]

Yes

[@hyparh]

Hi, can you run it without water (for some experiments) or it will burn out?

[@EDISON_SCIENCE_CORNER]

May beeee

[@apoorvakumarsingh861]

what will be the component if I have 2.7 GHz pizo electric disc

[@EDISON_SCIENCE_CORNER]

We cant use 2.7 mhz pieo here

[@apoorvakumarsingh861]

actually I have 2.7 GHz pizo so can you please publish a new circuit for that and if possible please give me your mail id

[@ninjatechnique5388]

Can i make air cooler use this?

[@EDISON_SCIENCE_CORNER]

Yes but not effective

[@Ingrid_01-j5k]

hola oye una pregunta por cuantos voltios puedo sustituir la pila?

[@EDISON_SCIENCE_CORNER]

Hi. Ask me in English please

[@vineet5968]

Are there any calculations to done to find the capacitance, resistance, power supply and all

[@EDISON_SCIENCE_CORNER]

Yes . Because the output frequency is determined by the RC components

[@EDISON_SCIENCE_CORNER]

You google search for that

[@vineet5968]

@@EDISON_SCIENCE_CORNER thanks and keep up the creativity

[@EDISON_SCIENCE_CORNER]

🤩🤩🤩

[@srikanthtatineni5928]

Appreciate your job, nice video. request you to provide the circuit for 2.4MHz disk.

[@EDISON_SCIENCE_CORNER]

Thanks. I dont have the circuit for 2.4mhz

[@panthLeoJTm]

Many thanks Sir, so how to make a humitity sensor now in order to make this humitity monitoring? I need to connect a humitdity sensor at any circuit witch, when need, switchs automatically on or Off the mistmaker circuit. (Without arduino please)

[@EDISON_SCIENCE_CORNER]

Check my other videos

[@alagappanssokalingam2459]

If developed this idea can be used in textiles .b cas they want mistifiresr to reduced heat as well as humidty Humidity took important place in spinning idstru .yarn quality will increases and yarn cut will be decreased .Any yar without cuts and knots will be a qualified yarn cotton or pokyaester .I thing this idea will take major use in textiles if reaserch and develope ment .And also it eill give particlar improve ment in garden industry or gardening bcas humidity ,p h and moisture will be controlled by misting.and finalky toy industry .gfor kids .thank u .

[@EDISON_SCIENCE_CORNER]

Yes we can use

[@scottm5425]

thanks, I think I'll build one for my model boat smoke effect

[@EDISON_SCIENCE_CORNER]

❤️

[@will3460]

How long would the battery power this for

[@EDISON_SCIENCE_CORNER]

Never tested that

[@will3460]

@@EDISON_SCIENCE_CORNER I wonder how this will play out in a small grow box for plants

[@EDISON_SCIENCE_CORNER]

Not getting you explain please

[@amirhazaghi1220]

I made the board according to the diagram, but when I connect it to the power, the mosft and the variable resistor get very hot, I have to disconnect it before it burns, and the piezo doesn't work either. I can't find the problem, can you help me??

[@EDISON_SCIENCE_CORNER]

Search great scott mist maker you can find the same

[@CLARVO]

From where did you order the ultrasonic mist disk

[@EDISON_SCIENCE_CORNER]

Check the video discription sir

[@arpitagarwal82]

How long can we continuously run this? 12-14 hours a day?

[@EDISON_SCIENCE_CORNER]

No we can't

[@ajitparmar5549]

bnane me jyada pese use hote hai.. batter hai ki.. Taiyar product hi le le .. vo bhi customize or aasani se kahi bhi le ja skte hai..

[@EDISON_SCIENCE_CORNER]

English please sir🙏

[@stevenelliott9821]

Nice work. Great info. very clear instructions and your items are well lit and visible. Thanks for the effort you put into this video.

[@EDISON_SCIENCE_CORNER]

Thanks brother

[@Artchemistshab]

Can we add 50 pieces of piezoelectric transducer in a single circuit board... I mean can a single circuit board operate 50 or 100 piezoelectric transducer???

[@EDISON_SCIENCE_CORNER]

No we cant sir.

[@durgasoundspayyanur7223]

Brother pls add more powerful mosfets to output stage the u can add more piezoeletric to one circuits

[@EDISON_SCIENCE_CORNER]

May be

[@durgasoundspayyanur7223]

It will work 100% bro, not may be

[@durgasoundspayyanur7223]

Thank you bro

[@robinsharma]

One more question Sir how can I make use of Arduino UNO with This mist maker

[@EDISON_SCIENCE_CORNER]

Yes

[@JugalAravind]

Can I use 108 kHz piezoelectric disc

[@EDISON_SCIENCE_CORNER]

Yes u can

[@marcelinbelisle2643]

any way i could control the on off with an arduino?

[@EDISON_SCIENCE_CORNER]

You can. Also check the channel video. There is a video with Arduino Uno

[@insideelectronics2203]

Why mosfet is getting overheated , i crossed checked your diagram and ciruit several time but issue is still there.

[@EDISON_SCIENCE_CORNER]

Use a heat sink

[@insideelectronics2203]

@@EDISON_SCIENCE_CORNER thanks for reply , but heat sink is not working it is getting super hot

[@insideelectronics2203]

How to lower the heating issue because ic is burning up.

[@insideelectronics2203]

circuit is not working at all, your reply will be helpful for me

[@EDISON_SCIENCE_CORNER]

May be problem with your connection

[@druciaki]

Great job! One doubt: the power source, is it 4,8v or 40,8v?

[@EDISON_SCIENCE_CORNER]

14.8V you can use 12volt. Thanks 😊

[@EDISON_SCIENCE_CORNER]

Noo

[@jinshadjinu6799]

Where i can purchase the piezoelectric disc

[@EDISON_SCIENCE_CORNER]

Link is in the discription

[@northindian344]

Very nice video 😀🤠

[@EDISON_SCIENCE_CORNER]

Thanks sir 😊

[@kartikagarwal9313]

Please share more details about the battery you are using, mine is not working for some reason, makes a low sound

[@EDISON_SCIENCE_CORNER]

Li ion 4 pieces in serial that is 14.8 volt

[@kartikagarwal9313]

@@EDISON_SCIENCE_CORNER can you give amps?

[@EDISON_SCIENCE_CORNER]

2ah

[@kartikagarwal9313]

@@EDISON_SCIENCE_CORNER thanks

[@EDISON_SCIENCE_CORNER]

Welcome sir

[@SANDEEP90909]

Can the circuit work on 12V dc??

[@EDISON_SCIENCE_CORNER]

14.8

[@SANDEEP90909]

@@EDISON_SCIENCE_CORNER will it work below 14.8v?

[@EDISON_SCIENCE_CORNER]

@@SANDEEP90909 not tested

[@SANDEEP90909]

@@EDISON_SCIENCE_CORNER please test it bro... then confirm whether it will work or not