How to Make TDA2030 Stereo Amplifier | Tda2030 Amplifier Module

How to Make TDA2030 Stereo Amplifier | Tda2030 Amplifier Module
TDA2030 Module Description:
1. On-board TDA2030A audio power amplifier chip.
2. Mono 18 w power amplifier circuit design.
3. On-board speaker terminal block
4 On-board 10k adjustable resistance, can adjust the volume of the amplification.
5. On-board power light.
6. Chip has lead to the main pin, can directly input audio signal.
7. Working voltage: 6 -12 v.
8. Board size: 31.6 (mm) x23.2 (mm).
Components Needed:
1. Tda2030 amplifier module
2. Heatsink
3. Wires
4. Sound speaker
5. DC socket
6. Audio Jack
7. 12v adaptor
8. Soldering
Subscribe to my channel and click the bell button to be updated on my next video. Thank you for watching♥️Enjoy and have a great day.
Subscribe to this channel: / javiersdiy
Related DIY videos:
DIY RC Car from Cardboard:
• How to Make RC Car Fro...
DIY 12v Power Supply:
• How to Make 12v Power ...
DIY 13000 mAh Powerbank:
• How to Make a 13000 mA...
DIY Sander Disk from Old DVD/CD player:
• How to Make a Mini San...
3 in 1 Power Supply:
• How to Make a 3 in 1 P...
DIY VU Meter:
• How to Make a VU Meter...
DIY Face shield:
• How to Make DIY Face S...
DIY Tester:
• How to Make Test Light...
DIY Flashlight:
• How to Make Emergency ...
DIY RC Car:
• How to Make RC Car Fro...
DIY Generator:
• How to Make Generator ...
DIY Air Cooler:
• How to Make a Powerful...
DIY Water Pump:
• How to Make Powerful W...
DIY Air Pump:
• How to Make an Air Pum...
#TDA2030amplifier
#TDA2030StereoAmplifier
#TDA2030amplifiermodule

[@veyselyazc2879]

Bravo👏👏👏

[@BrianCraigKeith31mm]

Thanks again. Great video.

[@JaviersDIY]

Thank you sir

[@info_bits]

This gets very hot.

[@JaviersDIY]

That's why i put a bigger heatsink sir.

[@amitghosh6966]

What should be the heatsink size (length and width) for single tda2030A ic if it is to deliver 10 watts@4 ohms on 12-0-12 V transformer supply ?

[@JaviersDIY]

Just to be sure sir please put a fan so that the heat will normalize

[@asuspentium4]

So does there have to be a jumper between vcc, gnd (signal) and gnd (power) of each module? the only one that does not have a bridge is In+? Thank you.

[@JaviersDIY]

No sir. Just look my connection again. Thanks

[@asuspentium4]

@@JaviersDIY I already saw it, you joined vcc + with vcc + then current negative with current negative and finally signal negative with signal negative, then you joined that signal negative bridge with the gnd of the jack and L and R of the jack with each positive signal (in+).

[@JaviersDIY]

@@asuspentium4 yes correct sir.

[@kerimcls]

Can we plug one 10k potentiometer into two circuits?

[@JaviersDIY]

Yes sir. You can

[@kerimcls]

@@JaviersDIY how about?

[@anti_mainstream6960]

I use this modul with a 5 inch 20 watt 6 ohm speaker plus tweeter. At below half volume the sound feel good. But when I turn the volume over half the sound become bad. Do you know why this happen? Thx

[@JaviersDIY]

Because of your powersupply.

[@anti_mainstream6960]

@@JaviersDIY then how much minimal current need??

[@JaviersDIY]

3-5 A

[@MACFiFth]

@@JaviersDIY actually you can use 20v 1a or 14v 1.5a or 20 watts of power supply.

[@satyajeetpatra7920]

Sar mono 2 channel stereo diagram bataiye

[@JaviersDIY]

Please speak english for better understanding sir.

[@MACFiFth]

i got this amplifier module too and the power output was 15 watts at 4 ohm unlike the one in datasheet and the IC was TDA2030a so i would say that the fake tda2030a soldered in the module has the same specs of original tda2030 also use 470uF 25v Capacitor or 1000uF 25v for better results on the output of module (replacing capacitor) its just worth $1

[@JaviersDIY]

As you can see on the module sir it's looks small so it means the output wattage will be also small.

[@gilman7608]

Is 1000uf 25v really improve performance? I read somewhere it increases the base

[@JaviersDIY]

@@gilman7608 no sir.

[@karthikeyankarthikeyan5886]

Hi sir 12 volt transformer power supply ok or 12 volt adaptor

[@JaviersDIY]

any of that supply sir as long as the current is sufficient

[@mltube9975]

Any heat problem?

[@JaviersDIY]

The heat is normal sir it is because I put a bigger heatsink

[@aksinstituteoflearningengl7176]

Sir can i run this module on 9 volt with a 4 inch speaker

[@JaviersDIY]

No sir

[@aksinstituteoflearningengl7176]

But this module is from 6-12 volt Then it must be run on 9 volt

[@aksinstituteoflearningengl7176]

@@JaviersDIY sir could you please suggest a 9volt amplifier module running with a bettery

[@SSchannel_353]

Sir how many amps it would require minimum

[@JaviersDIY]

2 amperes sir

[@poketamizha3708]

Bro can i use 5v 1a will it give full output?

[@JaviersDIY]

No sir. Less input also have less output.

[@ManinderSingh-ox4uf]

What is watt of the speakers

[@JaviersDIY]

50W sir

[@kirildimitrov1912]

How many volts are they?

[@JaviersDIY]

12V sir

[@rampr735]

Yah do speaker bajar sakta hai

[@JaviersDIY]

For better understanding please use the universal language

[@Jigri_gamer]

Output kesa hai mtlb aawaz

[@JaviersDIY]

For better understanding please use the universal language

[@Jigri_gamer]

@@JaviersDIY sorry, How's the voice and thanks.😅

[@JaviersDIY]

@@Jigri_gamer the sound is good sir

[@Jigri_gamer]

@@JaviersDIY Which output is best 6 or 12. Does this module heat too much.

[@JaviersDIY]

@@Jigri_gamer what output do you mean sir? When it comes to heat, you need to put a hard heatsink to normalize the heat of the IC

[@djnoisechile]

se escucha pesimo, es el microfono de la camara cierto ?

[@JaviersDIY]

For better understanding please use the universal language

[@djnoisechile]

@@JaviersDIY español latino es el universañ, qie te ciesta traducir

[@fixnreview]

Kana gyud! Wayhunonghangtodsatumoyligsannatongtanandaghangpahinumdomsaimongkalsada

[@JaviersDIY]

Salamat kaau sir.

[@fixnreview]

@@JaviersDIY way sapayan

[@erwinkarsindu2127]

Maaf seblmnya kak.. Terlalu cepat.. sy yg pemula bingung apalagi tdk tdk ada kata2 nya.. mana yg + mana yg - kabel jg banyak gk tau arusnya kak ?! 😭😭😭😭😭

[@JaviersDIY]

for better understanding please use the universal language

[@trendy2349]

That arduino modul has fake chip.

[@JaviersDIY]

No sir. It is fully functioning

[@trendy2349]

@@JaviersDIY of corse, that can bee votking! But miss the producter logo from the chip.

[@mohmadamintalby6978]

Bravo👏👏👏

[@JaviersDIY]

Thank you sir