How to make Ultrasonic Mist Maker fogger - Very Simple way

[@alexsandrgirs0912bori]

Good circuit, only without moisture protection after 20 minutes the cooler is finished

[@dr.vivekganesan2116]

How to protect the circuit from moisture...

[@lonewretch]

@@dr.vivekganesan2116 Put it in rice overnight.

[@austhinker4191]

1. Readers should be careful to ensure that their fan is 24 volt. Most fans like this are either 12v, 5v. or mains powered. If you have a 12v fan and want to use it, you need to either use a separate power supply or put a 12v Zener diode with at least equal power rating in series with it - cheaper if you don't mind wasting a tiny bit of power (about 2.4 watts for the same power fan as X-Creation uses). Or put two fans (identical power) in series, and use the other for another fogger or something else. If you use separate power supplies you don't have to cut the fogger cord - just push the connector through the hole from the inside - if it's too big, cut a small slot or two to give more room, then seal them with the hot melt glue. 2. Putting the holes at, or near, the corners of the container can allow all lid clips to engage for a more secure seal. Mark the holes and check that they are not in the way of the clips before making the holes.

[@jean-lucfornier5928]

you can use a step down converter for 1-2 bucks

[@angadimaheshkumar2586]

Hi bro in this I can fill the sanitizer liquid it can work pls tell me

[@passiveincome8564]

Can it work with any liquid like red blue pen ink too to dte colored mist or just with water?

[@grosbar]

How to make a mist maker? 1. Buy it. End

[@YoDay]

You'll make more sense if you watch the GreatScott Mist maker diy or buy video

[@victorius2006]

How It is made?... Buy a mist maker 😂

[@mahdjoubsofiane4005]

How to install a mist maker .

[@geetanjaleechandra9575]

🤣🤣🤣🤣

[@RetroArcStudios]

How to avoid the splashback created by the original mist maker

[@mrhkexperiment]

good

[@TalismancerM]

A great way to improve this would be to add a "pet water feeder" component to the tank so that the water level stays at the correct level for long periods and water doesn't splash into the fan electrics.

[@jean-yvesbeguec9944]

Thanks. Very useful to cool cutting tools (lathe ...)

[@Chmath_bro]

will this cool the room

[@abyss610]

i've thought about doing something similar to this but using one of those gravity fed dog food dishes, it would keep the level constant and you could use a gallon jug to feed into it. think it would work? on Amazon now looking through my options to try out.

[@liamp3332]

howd that go? Sounds possible.

[@nitrodamuz]

How long will the water empty?

[@owindustry]

is it hot or cold fog?

[@marx875]

On 12v battery possible?

[@atifzameer8387]

Dear how much price dynamic plates or power supply,

[@terencefranzindenerio9386]

Does it work with 24v battery??

[@MadPaperPeople]

sonic mister will lift water about 4 inches and so your fan will get wet...

[@rafarizky7184]

Yes bro, it is recommended to use a taller container

[@geographynoob6959]

more volts more smokeee?

[@marx875]

How to make with 12v battery only?

[@OddlyTugs]

How to make a mist maker: Buy a mist maker

[@Amar-sf3pn]

Lmao 😂

[@marcint5078]

If you set lower voltage will it also work but with smaller fog?

[@littletechkids9440]

It might and it most likely will

[@ron6126]

Good.

[@kumarson1]

Hi Nice video Please tell me what is the liquid you use for this

[@hollywebster1878]

H2O

[@pashajbl6647]

Good video man i love it

[@pablopastor508]

YOU DIDN'T MAKE A FOGGER. YOU BAUGHT ONE AND PUT IT IN A CUP.

[@pablopastor508]

• Itaku • Le Read the title AGAIN .

[@bhollywood01]

my thoughts exactly!

[@gopaldas9711]

Also right your coment

[@bartacomuskidd775]

that device is called a pond fogger.. the title is bad.. and on a side note you CANT make one easier than just buy one. Your welcome

[@justaninfiredperson]

Pablo Pastor is that most hot

[@yaelrodriguezalfante576]

Gud am po, ano pong tawag sa inilagay nyong instrument inilagay nyo s tubig salamat po

[@cedricharveydagarat7499]

humidifier

[@pekkavienonen6734]

Can I do that with the Battery?

[@HIGHER7RUTH]

I forget to like and subcribe bahaha

[@electronic7979]

Nice project

[@indianwalker8544]

Plz tell which song is in the background

[@DSCYERNEST]

Brother, what was that thing you put inside the container, what is it called?

[@voidremoved]

atomizer

[@pup8130]

battery

[@lonewretch]

Atomic battery.

[@meme-mx2cz]

Water

[@mg-kf3jc]

I click the link n the page i refer to was not found/?

[@jordanmiles1029]

can I use 12v fan with 24v adapter?

[@christianstrati3872]

Not really xD you need a "step down converter" it lowers the voltage to what you want it to be. Just search it on ebay ^^

[@chillzwinter]

You could solder in a 5 cent resistor in series with the 12 volt fan, you just need to know how much current the fan draws, then apply ohms law to calculate the resistor value. You could even put in a slightly higher value resistor than required to slow the fan down a little, as it doesn't need to be blowing at full speed, and less speed would give you a better mist flow effect.

[@lonewretch]

Yes... but it will probably explode.

[@3rd_Millennium_Engineering]

Hello X-Creation! Very cool idea! I would like to try this out on a 1/96th scale model I am building of the Apollo-era Saturn V with it's associated mobile launcher and Launch Umbilical Tower (LUT). I'd like to simulate the vapor coming from various components of the LUT and perhaps your idea can be incorporated into it. Any thoughts?

[@reganronald8328]

Dry ice

[@muhbahriilmi9411]

Bang dimana ada di jual yg putih di dlm mist maker

[@indianwalker8544]

Uh are awesome

[@odorouswo1f]

Not called a mist maker. Traditional humans call it a **HUMIDIFIER**

[@dylxnchn]

Yes

[@reakda3410]

no it is called a mist maker dumba**

[@lonewretch]

@@reakda3410 mist maker dumba** ? you mean it makes your bottom foggy? I say...

[@metaobserver657]

watch my video on connecting wires, did you even solder at 2:40?

[@lonewretch]

Solder? Where we're going, we don't need solder. HOT GLUE ALL HE WAY BABY....

[@laverite4493]

what we need for make this ultrasonic Mist Maker fogger ??

[@michafernandezincubadora2065]

hello how can i get the humidifier or why name buy it online

[@aaron-4567]

You can get it from amazon with 15€

[@little_astro581]

Where can i buy (links not working)

[@andrzejmadler2650]

Hi. I've tried similar solution, but the fan burned out after less than hour. I am wondering where is the problem. Splashing on fan damaged it, or to maybe there is to large current. Any ideas how to solve it? Spec below: Ultrasonic humidifier DC 24V ~500mA Computer fan 24V ~60mA 24V 800mA DC power supply

[@Chaoddity]

1- computer fans arent meant to be subjected to that level of humidity 2- This design also requires the fan to create a higher pressure to force air out a smaller diameter hole than the tube it came in through. CPU fans are just made to move air, not force it. Potental solution to problem one would be to put a mesh or filter in front of the fan to reduce contact with moisture. Potential solution to problem two would be to create an exit whole equal to the entrence. When driving CPU fans I recommend PWM over direct current. Also try not to provide too many amps. a low-tech solution to increasing the life of your fan would be to stick a variable resistor before your CPU fan and turn it up until the fan reaches it's highest speed. Anything beyond that is just pumping unecessary, damaging current through it which turns to heat and damages the component.

[@grecialuz1546]

Hi, Can you add essential oils to the water? please.

[@littletechkids9440]

Yes it wouldnt harm it

[@northhiburan3558]

0:13 wait the second, that fan 5 volt not 24 volt

[@АнжеликаБондарец-щ6б]

It isn't a very good scheme: the fan is working at 100% humidity conditions. It will be broken after several weeks due to corrosion of the electronic board

[@momdadandme9884]

What is the cost of this project

[@belikeemi3695]

love ❤️ it

[@schubi128]

Does anyone know why the foggers all work with 24 Volt?

[@aguswidi9316]

Nice. How long is the vogger last?

[@smshuvogazi1302]

Etree Ultrasonic Mist Maker Price?

[@troycasper3657]

I thought this video was about how to make an ultrasonic mist maker, not buy one and decorate it

[@opgg8024]

can it connect to arduino?

[@TavoosMassage]

Sure but only as a power switch

[@pakistaniyoutuber6666]

Price of purifier

[@ThePhiloctopus]

That moment you realise you put the cable out and spout in the way of the locking mechanism! Could have been avoided.

[@m7md0zeid]

where is the creation?

[@bloneyo1]

Very Kool, but not very easy, many things have to be bought. Again Very Kool and thanks for Sharing.

[@vikrantsharma6172]

Well tried

[@RaptorJesus.]

its probably bad to have the fan directly over the mist maker, because of the splash ;)

[@LittleFullLotaSap]

Why not just buy a Zoo Med Reptifogger? They work great.

[@minecraftcufanii7580]

Why havent YOU built the gadget ?

[@flyingdutchmanindustries5877]

I don't understand, what is the purpose of the music?

[@Златамассажист]

Всё такое маленнькое сплошная экономия

[@slewins4978]

very concerned about the fogger splashing water into electrical fan !!

[@Futuremedics1]

Without battery it will work

[@christianmccauley7340]

sunitha Reddy no it won’t.

[@MikkeMan]

how is tuning your wires simple?

[@gilbertobarber8147]

Oye amigo ...muy buen video...una pregunta cómo se llama el aparatito k genera el vapor.....te agradecería tu respuesta

[@pedrobg1289]

Se llama MIST MAKER O FOGGER .

[@safaaimrankitchen]

What's the mist fogger??why everyone used the!?

[@pup8130]

because they do

[@mrawesome6239]

24v to that tiny fan? How? Looks like a pc fan which is usually 12v. What’s going on?

[@suicidallkilljoyheadshot7866]

Mr Awesome it’s a 24v dc fan

[@suicidallkilljoyheadshot7866]

Mr Awesome about 8 bucks on amazon

[@mrawesome6239]

SUICIDALLKILLJOY k bought a 12v fan off eBay for 50p and got a 12v to 24v circuit for £1 was much cheaper.

[@lonewretch]

some math. but mostly errors.

[@kietnguyen308]

Việt nam 🇻🇳🇻🇳🇻🇳 đâu rồi kk điểm danh

[@HungVu-zc2cr]

điểm danh để làm gì?? ứng dụng cái này vào đâu được bạn??

[@olgerperez2417]

SOY ASMATICO CON ESO ME PUEDE SALVAR LA VIDA

[@tomasmillan7324]

Materials in spanish please. Tanks.

[@warga_enamdua]

Joss

[@Kwemony]

Says simple, "you have to buy a carbon hydro pump, and buy a hydrolic fog producer that will be strong enough for the pressure to rise and blow up"

[@kamranahmed6800]

cool video but i think i will just buy one lol

[@kajallison8896]

By cutting that cable you could getshocked

[@junaedisyam5912]

Alat2 apa sja itu bang, apa nama2 alatx bang tolong di jelaskan dulu makasih sebelumnya 🙏👍

[@jodijodiansyah4462]

Bang betapa harga mesin embung

[@Clicksby_shine]

link pls

[@XCreation]

check again, please. I just have updated

[@sajeduli3]

That was just water ?

[@annemariemiguel2541]

Sajedul Islam yes it was just water

[@fathichouikh6402]

@@annemariemiguel2541 hot or cold waterplz

[@pup8130]

@@fathichouikh6402 water

[@mahin-bb4ev]

Make a mist maker plate. Urself that is creation

[@ndulucomedian8886]

may I call it nebulizer?

[@venkatkarampudi]

the hell? you didnt make it dude you bought it???? How the hell did you get like 3.2k likes? like this comment if you agree

[@a.knottycurl]

Is there anyway to use marijuana with this so that it ? So that the steam is marijuana steam or mist ?

[@Phougi]

You could probably make a bowl on the top of the container and light it as the fog is running. It might be strong enough to create a vacuum and pull air through the burning marijuana.

[@raisfathroosdian5120]

JPB - High

[@thesilentcoda]

Thank you! Kind of a low move to use someone’s music and not even link it

[@mobarokhossain3317]

Yoyo

[@masterbrosgames410]

Basically this video: how to build ulrasonic mist maker. Youll need an ultrasonic mist maker. what

[@cagroguzal579]

Link ???

[@XCreation]

follow the buy link below this video

[@mattperez7933]

@@XCreation dont work. Is there an updated one?

[@ralltodieal409]

Alex gyver?)

[@andreejmarbbf52]

You need to make some changes. Check Avasva Solutions if you want to make it right.

[@hamzah.4470]

my father said smoke is not good for health

[@XCreation]

this is mist, not smoker

[@hamzah.4470]

@@XCreation Ow, I want to buy it but I don't have the money :)

[@milance2111]

I use adapter that have 24 v and 3,1 amper...it does not fucking work

[@lonewretch]

probably because it's not meant to run a 24v fan and a 24v atomizer at the same time.

[@hnjbiy8373]

Looks like you can smoke weed

[@polvocorrupto]

vape nation

[@teyeighty8k]

Misleading...

[@AbdShadow]

How to make mist maker, just buy it

[@MBgav0]

Diy vape

[@mariaesthelablandino1396]

Klk

[@ledmk2]

Funny

[@cojito1527]

Hola dame corazon

[@youssefehap5136]

غ

[@Bart3k]

ip ip ip hi