Thanks for the pictures of the pressure release, I released the pressure motor went down now it works great. Thanks again 👍
@nnamdiamah306110 ай бұрын
Good morning, I love the video, if a trim stops can it be serviced or you need to get a new one completely
@richardgarcia28672 жыл бұрын
Very good - thanks for sharing your knowledge and suggestions 👍
@jasonfrat98132 жыл бұрын
Thanks for your comment. Hope the video helped you!
@iamburl2667 Жыл бұрын
How come mine does not have any screw for what your doing, I have two rams that work my trim, on my mercury 69 ob , there is no screw to lower it
@pierreetchamendy29952 жыл бұрын
Thannks, very useful information
@jasonfrat98132 жыл бұрын
Glad to hear!
@antemaric5623 жыл бұрын
Thank you for this video, I have one question, is it possible to do this procedure while the boat is still in the sea. Because this bolt is few centimeters below the surface and I am afraid that water could leak inside.
@jasonfrat98133 жыл бұрын
Glad it was helpful, maybe you can transfer enough weight to the front of the boat to get it above the water. Otherwise, just crack it enough to get tilt and then when the boat is out inspect the fluid and change if necessary. Id be surprised if you got any in there though.
@antemaric5623 жыл бұрын
@@jasonfrat9813 thanks for the answer, I'll try it.
@kenbowler34102 жыл бұрын
Where did you locate the after market motor replacement? I have the identical motor and issue. Great video since my motor is in the up position! Once I release the screw it should come down on its own I hope. Thanks Ken
@user-pu9ur6cz5r8 ай бұрын
I have 2008 F90 4 stroke yamaha. Need the link for aftermarket trim motor.
@nickkostakis96002 жыл бұрын
Great video thank you very much
@jasonfrat98132 жыл бұрын
Thank you, glad it helped!
@randylee68232 жыл бұрын
My trim don't work at all. I have no trim motor sound at all. Should I replace trim motor or check my electrical first?
@glennlacey72572 жыл бұрын
Thanks man for the info. Worked like a charm.
@glennlacey72572 жыл бұрын
This worked on my Suzuki 115 outboard. Same principle.
@jasonfrat98132 жыл бұрын
Glad it worked. Sometimes even a key or coin can get you out of a pinch
@davidsaber46433 жыл бұрын
Help, my 40hp Honda is locked down about 20 inches in ocean water. There are TWO screws. Cant see it, only feel it. Which is the relief? If I turn it salt water goes in. Can I flush once the engines up? Boat over 20 ft of cold ocean. Could you video each step for a Honda? Show it’s step not face shot explanations. Like the dog!
@nemanjalaganin93102 жыл бұрын
My manual tilt screw is threaded can yous please help?what do I do?
@joshua.wolfe13 жыл бұрын
Thanks Bud! Just helped us out big time !!!
@jasonfrat98133 жыл бұрын
I'm glad, good to know in a pinch
@markdarder33354 жыл бұрын
thanks. I have a trim issue right now and this video will help me. I have fluid all over lower unit. trim motor is working - I see motor move about 1/4 inch and then stops and I can get that 1/4 to retreat so motor is working. I think I lost hydraulics some how. Now I have to figure out how lift this monster Yamaha 225 4 stroke by myself and then I hope I have that little brake you used. If not I will need to bring a block of wood with me to keep motor up during transit to the shop. If I do need a new unit - you said you found an after market motor. Can I get the details on where you order it from?
@GilmoreStrat2 жыл бұрын
So I just had a dead battery and needed to lower it, so I undid the screw, how do you reverse this? Got the battery up, and I re tightened the screw, but the engine does not move up ot down. . The trim motor runs and it is on a new Suzuki DF20A 2021
@jasonfrat98132 жыл бұрын
If no oil drained out when lowering, is it possible there is a latching mechanism it is working against? I am unfamiliar of that model. Perhaps running the motor back and forth could remove air if that is an issue too.
@danielolinn89714 жыл бұрын
1999 Johnson 200 hp I cannot release the scre.w to let the motor down.....is there a retaining clip, or just possibly frozen up?
@danreddy54824 жыл бұрын
Wondering how you made out I hear the bolts are sometime plastic , heat with torch , jam flathead hard into bolt , let cool and harden and turn it out is what worked for 1 guy
@jasonfrat98134 жыл бұрын
My experience has been stainless screws often froze in the aluminum. Try a hammer actuated impact driver. Works everytime if the screw slot is intact. www.homedepot.com/p/TEKTON-3-8-in-Drive-Impact-Screwdriver-Set-7-Piece-2905/205674679
@351kostakis2 жыл бұрын
Fantastic
@helgawm20102 жыл бұрын
helps - thx alot
@rickygrantham21784 жыл бұрын
Good to know!
@charlesbunting92273 жыл бұрын
thanks
@fillw9752 жыл бұрын
Turned the screw counter clockwise 1 3/4 turn got the motor up opened the filler bolt, oil shot out all over me. Normal??