How To | Mazda 3 | 2019 + Present | Oil Change Oil Reset

Vehicle In This Video: 2019 Mazda 3
2.5L
Oil Type: 0W-20
Oil Capacity : 4.8 Quarts 4.5 Liters
Engine Oil Drain Plug Torque: 30 Ft. Lbs.
Wheel Fastener Torque: 108 Ft.Lbs / 146 Newtons
Oil change interval and oil life reset on 2019 2020 2021 2022 + Mazda3 Vehicles.It might be same procedure for other Mazda Cars....
Support Us On PATREON: bit.ly/3qQsO07
Support Us On PAYPAL: bit.ly/3r4DPdJ...
--------------------------------------TOOLS I OWN--------------------------------------
30 Degree Push Pin Removal Pliers: amzn.to/3BlCx1K
Wheel Stud Installer amzn.to/2TQkstm
Stretch Belt Tool amzn.to/3e8bYVk
Gear Wrench 1/2 Socket Set amzn.to/3e6XDIv
Disposable Gloves amzn.to/3e3Bc6Y
Toyota/Lexus Oil Filter Tool amzn.to/3k6wuti
Vacuum Brake Fluid Bleeder ​​amzn.to/3xzATZB
Gearwrench Ratcheting ​​​​amzn.to/2Vm2kHU
7-Piece Spare Tire Retrieval Tool Kit amzn.to/2VlKWmE
Oil Filter Wrench Wrench Kit amzn.to/3ARUjLi
Oil Filter Pliers ​​amzn.to/3yENJpo
Craftsman 1/2 Impact Sockets Set ​​amzn.to/3e5z92e
Screw Driver Set ​​amzn.to/3hYt5K5
Hand Impact Driver Set amzn.to/3yFdF48
Dual Piston Brake Caliper Push Tool amzn.to/3yJDe47
Wind Back Brake Caliper Tool Set amzn.to/3yKGlsJ
--------------------------------------------------------------------------------------------------------
If this video helped, let us know in the comments, and if you liked this tutorial, leave a like and subscribe fore more content like this! Thanks for watching!
Repair Tips & Secrets Only Mechanics Know
DISCLAIMER: This video description contains affiliate links, which means that if you click on one of the product links, I’ll receive a small commission.
#howto #diy #Mazda3oilchange

[@autofigure00]

Love that they put the oil filter in the same area as the drain plug

[@chrisosman2895]

Came here to say this. Holy shit; why did I ever let a tech do it once

[@davidbarlowjr7583]

I know right! Holy shit an engineer hooked it up for once

[@renocool1558]

I was looking for metal to place a jack under. All I see is that damn plastic. Where would you put it?

[@autofigure00]

@@renocool1558 there's the dedicated jack points like 6in behind the front wheels and in front of the rear wheels (common place on most cars where the jack that comes with the car is meant to go, you can find a picture in the owner's manual of those points). That bar running between the front and rear wheels is underneath the frame and it is reinforced metal you can jack from.

[@renocool1558]

@drewlehman2456 I have this (hydraulic I guess) jack that I used to put on some metal under the hood, but I can see nothing but plastic cover here. Thanx though. I might just have to put in on the side like tire jack

[@pillage-]

Thank you so much. Figured it was time to learn and change my own oil to save money! Also didn’t want to wait 1.5 hours at the dealership

[@leosheppard8517]

Btw it’s called a stealership lol

[@hddiaz91]

These new cars intimidate me but your videos ease up my nerves thank you

[@nanascho3]

You sure about that min/max? Looks like you had them reversed. Wouldn’t the higher one on the stick be the max line?

[@Cleoleoleo]

I was thinking the same thing

[@AutomotiveDysfunction]

CORRECTION!! At <a href="#" class="seekto" data-time="309">5:09</a> minutes flip max and min lol

[@hurryingglint23]

I was gonna say…

[@fabianmanuelotero8446]

Also, didn't change the gasket ring on the oil drain plug, and didn't use a torque wrench to tighten the plug...possible oil leak.

[@Gritt982]

Mazda engines favor a high flow oil filter which is why they recommend the OEM Skyactiv oil filter, less flow resistance.

[@slickman5969]

Does the drain plug have a crush gasket?

[@MuffyThePomeranian]

this channel is underrated period.

[@AutomotiveDysfunction]

Thank you .. it means a lot

[@TheDaddo95]

​@@AutomotiveDysfunction ciao, Could you please tell me the nm to tighten the oil bolt and oil filter please. Thanks for all

[@alexsosa2962]

Thanks; I will do this by my self; really dont trust in Mazda Mexico Dealer

[@ifacecheck]

[@nastysoda9212]

so glad it uses a canister type oil filter, thank god

[@timohalloran3159]

I always punch a hole in the bottom of the filter before I remove it, cuts down on the big mess that it makes.

[@docesam]

rare to see that tip

[@Lemon83166]

Well if you empty the oil first then u wont have a big mess, especially since the filter is tilted down and not sideways. This guy just unscrewed it while it was full of oil. Clearly has no patience.

[@ampm9771]

What is the thread depth of the drain plug? Is it at least 10mm deep? BTW ALWAYS PRE-FILL the oil filter, you don't want the engine components such as VVT to run dry even for split second.

[@Lemon83166]

Keep ur opinions to urself especially when u dont know shit. M14 1.5mm bolt. Couldnt u be bothered to google it? But u can be bothered to pre- fill a filter. Hm. Stupid logic you have.

[@leosheppard8517]

Great car. Well thought out. I am on my third Mazda. I have the same 2.5L engine. Not sure why USA have 0w20 oil, while Australia uses 5w25 or 10w20 or 30. I just follow what the mechanic says.

[@toddzino58]

CAFE requirements in the USA. Rest of world uses 5W-30. In USA manual, it says "Recommended" 0W-20, but 0W-20 "required" for fuel economy.

[@leosheppard8517]

<a href="#" class="seekto" data-time="58">0:58</a> is there a flat spot in the rim (or tyre)? Left of screen

[@julioespinoza3]

My kind of therapy

[@azvasamusic7095]

The only thing that worries me is you Didn’t use click or digital torque wrench at the end for the oil pan bolt I’m sure you’ve done enough to actually tight it feels But I like to do everything to spec Do you know what it is wether in inch or ft

[@AutomotiveDysfunction]

Look in description of video it’s says 30ftl for oil drain plug

[@HrvojeMihajlic]

you should also take care of that bent rim.

[@jonathanhernandez3750]

How ofter change the oil? Every 5k miles?

[@SicilianAmericanDreams]

3K - Ideally. You can get away with 5K tho

[@silentstormstudios]

OEM service schedule says 7,500 mile oil change intervals. This car uses full synthetic, so you can go at least 5k. Doing every 3k is outdated old school thinking and throwing money down the drain with a modern engine using synthetic oils. Not necessary unless you're following a severe service schedule.

[@troybassant2427]

What’s the best possible oil filter to use on a 2021 Mazda 3 hatchback, 2.5L, non turbo.

[@RadioStaring]

Just use Toyoko Roki, it's what the designers had in mind when creating the engine.

[@CalumNoade]

OEM

[@blackbenz4125]

Wieviel Drehmoment braucht die schrsube und der Filter? Ist der Filter Handfest?

[@user-ym8jk6yz2k]

I added the full 5 quarts not the 4.8, should I empty it or is it ok ?

[@AutomotiveDysfunction]

its ok

[@Valid.4l]

Thank you so much

[@Ricardo-db1kt]

Thankyou!

[@justinelaxamana9612]

recommended tourque specification for the drain plug?

[@AutomotiveDysfunction]

in description of video

[@TheDaddo95]

Filtro FRAM XG6607 Ultra Synthetic Va bene per quest'auto? Grazie a tutti

[@SicilianAmericanDreams]

Someone else here said they use that stuff

[@Valid.4l]

How do you know which oil filter to get? Also where would I put a jack?

[@AutomotiveDysfunction]

Use jack on pinch-weld.. and for oil filter walk in any local auto part house and ask for oil filter for year/model/engine size/ and they ll let you know

[@Valid.4l]

@@AutomotiveDysfunction thank you also should I go cheap on tools or pay for a good brand?

[@AutomotiveDysfunction]

@@Valid.4l cheap .. if you won't be using it everyday

[@romel420]

@@Valid.4l Fine to go cheap for hand tools, just don't go cheap on ramps/wheel stops/jack and jackstands. You might not live to regret it if those ever failed on you lol.

[@silentstormstudios]

Always use jack stands or ramps to support a vehicle that you're working under. NEVER rely solely on a jack.

[@AVG1597]

what is the amount of oil it takes ?

[@AutomotiveDysfunction]

in description

[@timothysmith7700]

The wheels bent from potholes lol

[@SicilianAmericanDreams]

That's not funny that's sad 😢 I hate pot holes they have cost me thousands of dollars in damage to my vehicles!

[@timothysmith7700]

@@SicilianAmericanDreams trust me. My wallets been hurt too. Especially winter time.

[@gavinbritt1349]

Lol the front passenger side wheel is bent

[@AutomotiveDysfunction]

lol just seen that

[@sebastianespinoza7673]

Can you please put a link to the oil filter that was used in this video.

[@AutomotiveDysfunction]

I can't its not for sale.. but you can go to any local auto parts zone let them know info on your car and they will tell you which oil filter you ll need

[@fabianmanuelotero8446]

I use Fram Ultra Synthetic XG6607 oil filter on my 2019 Mazda 3 HB with Castrol Edge Advanced Full Synthetic 0w-20 oil. Make sure to install a new oil drain plug gasket with each oil change.

[@MrCheezyCrack]

@@AutomotiveDysfunction 😆😆🤣

[@MrCheezyCrack]

Always use a manufacturer oil filter. Go to your nearest Mazda dealership and buy a bunch of filters: they're only like 7 dollars.

[@SicilianAmericanDreams]

​@@MrCheezyCrackthanks for the tip!

[@andresc5915]

I hate when the oil filter is only accessible under the car.

[@AutomotiveDysfunction]

Lol true … but must of European vehicles like Audi/Mercedes/bmw oil filter are on top of engine easy to access

[@andresc5915]

@@AutomotiveDysfunction Yeah. I love that about German cars and that’s how my Mercedes is…. But it’s constant issues and maintenance with German cars…Super exhausting. I’d rather go under the car at this point. 😭

[@darwinfromme4724]

Am i the only one or is trat Front Wheel in the First Minute in a Bad shape😂

[@johnnyd768]

Yeah, I noticed that too. Looks like it's dented. Also would have been nice to see the tech drain all of the oil, that's why I always do my own oil changes.

[@beyond305]

Uses the old oil the lube the new O ring….

[@DavidTMSN]

It's fine.

[@toddzino58]

Not an issue. Literally at all.

[@beyond305]

@@toddzino58 you re-use your toilet paper too i see