How to Monitor RV Batteries On A Budget.Install 10€ Digital Multimeter Voltage Amperage Power Energy

Install and Review 10€ Digital Multimeter DC 6.5-100V 0-100A Voltage Amperage Power Energy
DC 4-in-1 LCD Display Digital Current Voltage Power Energy s.click.aliexpress.com/e/_AAMYl6
AC 4-in-1 LCD Display Digital Current Voltage Power Energy s.click.aliexpress.com/e/_97BIyY
s.click.aliexpress.com/e/_AAMYl6
4-in-1 LCD Display Digital Current Voltage Power Energy amzn.to/2R13BiG
if you want to support my channel : PayPal Donate Button Link :www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=BZCEMTDQAMS6E&source=url
How to monitor RV ,car or solar batteries for less money with digital multi-function meter PZEM-051 DC6.5-100V 100A Voltage Amperage Power Energy Meter with 100A/75mV Shunt .
Review Battery Monitor PZEM-051 DC 6.5-100V 100A Digital DC Voltmeter Ammeter LCD 4 in 1 DC Volt Amp Power Energy Meter Tester with DC 50A/75mV Shunt
electrical parameter measurement function (voltage, current, power, energy). The voltage alarm function (over voltage alarm thresholds, backlighting and voltage flicker tips).The power button clear function.
Power-down data storage function.Large-screen LCD screen full display function (display voltage, current, power, energy).backlight.
1. Power: measurement range 0 ~ 10kW
2. Power: measurement range 0 ~ 9999kWh
3. Voltage: test range 6.5 ~ 100V
4. Current: Test Range 0 ~ 100A
Button
1. The backlight control
By short press the button to turn on or off the backlight, the backlight status automatic storage.
2. The power cleared
Step 1: Press the button until the power area show "CLr" character, then release the button;
Step 2: At this point in the power consumption flashing indicating the current status is cleared, if short press the button again, the consumption data is cleared and cleared quit flashing;
Step 3: If no key is pressed within five seconds, it means that the power does not clear the data and exit cleared.
3. The voltage alarm value
Step 1: Press the button until the power area show "SET" character, then release the button
Step 2: After entering this state, the voltage of the high pressure area shows the current alarm value, the current area displays the current value of low pressure alarm, and the least significant bit starts flashing, then you can press the button through the +1 bit short, when there is no button operation When more than three seconds, the automatic adjustment of the position switch from high pressure to low pressure alarm alarm value has a value, a total of six, the scope voltage alarm threshold set for the 6.5 ~ 99.9V
Step 3: After setting, press the button until the display shows "PASS" character indicates the setting is successful and automatically exit the setting mode.

[@MathewsSonya]

Awesome video! Love the speed .

[@kukomio]

Thanks :-)

[@joeo8396]

Thanks for adding the how to program the software.

[@nutriland315]

Well done

[@Argon71]

I will order one :D

[@ramdayaljat2257]

Nice and informative video

[@uhlpharmacy1213]

Nice

[@kukomio]

Thanks :-)

[@tanthanhdat]

I have used more than 20 of these. It will deviate from specifications after 1 or 2 years of use

[@lambertinos]

Is it possible to calibrate it?

[@antonis2814]

Do you known if we mast use Fuse?If yes,how many amperes?

[@ehlai1676]

You can't get the 4 readings for both the batteries and the solar panel, can you? It can only monitor the solar or the battery with one device, correct?

[@lauadvincula2113]

I used this to monitor discharge of my diy pack. After 2 cycles the meter doesn't want to show anything anymore. Would anyone know what causes this?

[@TchauRod]

My question on this meter is: I installed one on my 2x 200amp/h lithium battery 24v system, but which settings would i choose being that those readers are set for 100amp batteries? (1,2,3,4,5 batteries, but all 100amp) My meter shows 100% all the time. Gotta be wrong

[@skippercaship]

Excellent video I wish all videos could just show you what you need to do and not waffle on about their ups and downs

[@carrymanyvanh3579]

What wires do you use? I'm trying to set mine up and I'm inexperienced

[@miguelsalami]

So you are connecting Shunt inline on Negative? I have heard this is much safer this way?

[@techworld7988]

Hi sir, I am using Amicisense dc meter to check how many volts and amps are coming from solar. The meter is working fine in daytime but in night it's showing solar charging symbol in my pwm charge controller(like reverse charging) Please help me on this

[@jackmason7518]

Good Morning. why does my PZEM-051 Does my unit not show the right volts. Jack Mason

[@PavolFilek]

What is voltage error meas. and amps nonlinearity and amps offset error ? How will it integrate charge ? +- 1 Wh or +- 100 Wh per day ?

[@antonis2814]

All the time it flashes and voltage is flashing Also.I m putting voltage minimum and maximum and it is doing it again.Do you have any idea?

[@nicholastierney4016]

Great vid. At 0:55, what are you using to cover the exposed wire ends before you attached them to the meter? I’m having issue making a secure connection.

[@Bujoinferno]

Wire ferrule

[@ideafromkurdistan5257]

Hi thanks, 4 pin im display all posative ?

[@UDX4570PalmSprings-yh1mv]

Does this meter require voltage continuously or will the meter return to its previous settings when power is restored?

[@symonchester]

Great vid, will this also show charge rate when charging?

[@AIwithMaherMashaal]

🎯 Key Takeaways for quick navigation: 02:11 🎉 *Introduction to the Digital Multimeter* - Introduction to the digital multimeter and its features, - Explanation of the importance of monitoring RV batteries, - Overview of the budget-friendly digital multimeter being reviewed. 03:50 🔍 *Demonstration of Installation Process* - Step-by-step demonstration of how to install the digital multimeter, - Explanation of connections and setup required for monitoring RV batteries, - Tips for ensuring accurate readings during installation. 04:05 🎵 *Conclusion and Final Remarks* - Wrapping up the review of the digital multimeter, - Recap of its features and benefits for RV battery monitoring, - Final thoughts on its affordability and usefulness for RV owners. Made with HARPA AI

[@shoaibabbas1507]

Sir how to check solar watts watts through this meter

[@Maxttor]

I need it to measure Lithium Cell DC current capacity

[@blasstoria]

¡Hola! Tengo una consulta. La distribución de mi caja de breakers tiene 2 fases, sólo tengo 1 dispositivo. ¿Puedo adicionar otra bobina sensora a la otra fase y conectarlo al dispositivo en paralelo, o serie? Gracias.

[@alocin110]

Hi Kukomio, I want one to measure DC current and Volts; I would like to know what is this shunt made up of. Does it comes with the meter or it is something we have to make it at home? Please advise. Thank you for uploading a video for this meter. Keep up the good work.

[@timbateman5780]

The shunt comes with the voltmeter. Its very big and heavy with metal at each end, a bolt that allows you to bolt it to something and then a much smaller screw for fixing the leads from the voltmeter to the shunt.

[@josepeixoto3384]

mo noise!! thanks for the M key

[@molifehacks5258]

Question...can this meter work with lipo batteries? Thank you

[@bjornbevenborn1315]

yes it sure can.

[@pajoscz4664]

prosím .... co je ta černá svorkovnice? Pojistka?? PLEASE what is it the black stick? Fuse? I dont what is it :-((

[@kukomio]

je to bočník alebo šunt ( angl.) - nízkoohmový rezistor, zapojený v sérii so záťažou. Slúži na meranie prúdu prechádzajúceho záťažou.

[@KaranSingh-jm5qs]

multispan vaw 34dc solar se connection

[@arpadcsorba2053]

What is with all the bumpy bump music?

[@jcbdiggers1]

Fitted one in our motorhome but only get 4 reading when the batterys are charging..iam only getting the battery voltage when turned off from charging...am I wrong in saying this does not show any off the using amp's been draw..ie 12v TV is turned on or led lights..please help...thanks

[@i8BBQ4Lunch]

Did you ever get an answer? I just purchased one from Amazon and found the same issued. I had to swap the shunt wires into the meter in order to read the opposite direction. I am going to put a DPDT switch to fix. My shunt and gauge from Victron worked both directions. Maybe that is why this unit is so cheap.

[@yzf40]

Attention il faut pas le branché directement sur la batterie cette pièce chauffe il faut mètre un câble

[@Daniel-odanio]

does the device still work properly so far?

[@kukomio]

The digital multimeter works very well. It's connected from a solar mppt to a battery and shows exactly the same data as the Victron 150/35 MPPT app shows. So now I don't have to look at the victron connect application.

[@mysterychemical]

Let's say battery is connected to UPS/Inverter where there is both DC in to the battery while charging and DC out while discharging. On such situation what is the setup of this multimeter? Setup on this video is only during discharging. What about recording/monitoring charging amperage, wattage and energy usage too?

[@kukomio]

I currently use this multimeter to monitor solar energy from photovoltaic panels via MPPT to the battery and this kzbin.info/www/bejne/eqPFkqqXgLt0e9U I use to monitor battery capacity, charge and discharge current Amperage, Voltage

[@panoskatotriotis]

How can I turn the device off?

[@timbateman5780]

Hi, I put in an on/off switch inline wire from screw 1 (the wire that does not connect to the shunt). Then I can turn it on and off whenever I want so it does not draw power when not needed.

[@user-jx4bp1uj5l]

How to order this amper meter

[@kukomio]

DC 4-in-1 LCD Display Digital Current Voltage Power Energy s.click.aliexpress.com/e/_AAMYl6 AC 4-in-1 LCD Display Digital Current Voltage Power Energy s.click.aliexpress.com/e/_97BIyY s.click.aliexpress.com/e/_AAMYl6 4-in-1 LCD Display Digital Current Voltage Power Energy amzn.to/2R13BiG

[@NatishHD]

I have Got This (100V - 10A) Meter and i have found that 2 Adapters was written 9V and Coming 17V :D and another 13.3V and coming 6.5V. Now About Meter: You Can Use Meter Only With AC Adaptor Or Battery - To Turn on. Use Minimum 3V Maximum 12V and Maximum 1.5A. Use thin red (+) and thin black (-). thick Red - is changing Pulses thin Yellow - also changing Pulses thick Black - also changing Pulses 1) Volt measures thin Yellow and thick Black 2) Volt measures thin Yellow and thick Red 3) Amps measures thick Red and thick Black

[@user-yn3se6zj7b]

मुझे ये मिटर भेद दो

[@shawnroddick7523]

Dude get rid of that irritating ass music!