how to program 8051 using arduino

In this tutorial I have show you that how you can program 8051 microcontroller using arduino.
This tutorial provides you the right way to program 8051 microcontroller using arduino.
If this video was helpful than please like share and subscribe to my channel
Softwares used in this tutorial
8051 programmer: drive.google.com/file/d/1UYf-...
Arduino IDE: www.arduino.cc/en/Main/Software
Keil: www.keil.com/download/product/
Select C51 in the above link and fill the form to download keil.
code and circuit
Circuit Diagram: drive.google.com/file/d/1AmMU...
Code: drive.google.com/file/d/1gvoX...
hardware
breadboard jumpers :www.ebay.com/itm/65Pcs-Male-t...
Music provided by [NCS] NoCopyRightSounds
Track: Elektronomia - Summersong 2018 [NCS Release.
Watch: • Elektronomia - Summers...
Download: ncs.io/SummersongID

[@Bianchi77]

Nice information, thank you for sharing it, keep the video up :)

[@alisonleal9668]

Depois que programei deste modo não programa mais em outros circuitos programadores, pq? Travou?

[@nagendrababupampana4113]

Sir super

[@slambergamer91]

can i use this to program P87C51FC ic ?

[@softchae2787]

When I tried compiling the code in keil It says, compiling blinkled.c... blinkled.c(1): warning C318: can't open file 'REGXS52.h' blinkled.c(2): warning C318: can't open file 'delay.h' blinkled.c(8): error C202: 'P1_0': undefined identifier blinkled.c - 1 Error(s), 2 Warning(s).

[@varunmanchanda3972]

From where did you buy the Crystal? please provide the link

[@CircuitSageMatheus]

The 8051 programmer doesn't detect AT89S52 how to deal with it? I am using an Arduino Mega 2560, could this be the problem?

[@endtimerevealed137]

have i to bootload at89s52 before your process?

[@ikehsamuelifeanyi4925]

Can I use this programmer to reprogram the same microcontroller over and over again ?

[@alisonleal9668]

Please help me, because my AT89S51 stopped accepting programming after following this tutorial I managed to program before following your tutorial?

[@alisonleal9668]

Im dont have much money, can you help me with a simple circuit without Max 232 ou similar to program? Just using some resistors, zenners in serial db9 conector, i look in internet but no one Works, thank you so much

[@johnpiettro4644]

Your title suggests that you could do that with AT89C51 but it requires the parallel mode programming method. Anyone could figure out AT89S52 for sure.

[@nagendrababupampana4113]

Sir n76e003at20 ic program ????telme sir

[@Drxxx]

super project

[@hobbyelectronics2121]

thanks bro

[@alisonleal9668]

Obrigado pela iniciativa, vc pode disponibilizar o arquivo hex e o esquema das ligações do Blink para estudo? Muito obrigado

[@harakumarghadai7828]

one doubt! can we use Silicon TechnoLabs ATMEL 8051 AVR USB ISP Programmer using ic (ATMEGA8A-PU) in place of arduino UNO board, will it work? as i have no spare UNO board

[@hobbyelectronics2121]

Yes you can. In this video ISP interface is used to program 8051 using the arduino. You can program 8051(AT89Sx) series microcontroller with any ISP programmer.

[@gurumultitask9979]

where is the pin number of VREF and VIN?

[@danny3man]

Hey, very noob here, have a question. First you programmed the arduino. But to do what ? To be able to control the microchip ? Thanks.

[@muhammadhaziq9677]

Yup kinda. It is to make arduino functioning as a tool kit for the microcontroller

[@onurolce]

Can you also share your "delay.h" library for Keil IDE which you made a test firmware ?

[@hobbyelectronics2121]

Yeah sure here is the link : drive.google.com/file/d/18qAcswuawXbltfCCs8TbWZ6Q5uunUHZB/view?usp=sharing

[@softchae2787]

How about the REGXS52.h library?@@hobbyelectronics2121

[@babyph65]

@@hobbyelectronics2121 bro it doesn't work, delay.h(39): warning C206: 'Clock_kHz': missing function-prototype delay.h(64): warning C206: 'Delay_us': missing function-prototype delay.h(64): error C267: 'Delay_us': requires ANSI-style prototype ledblinking.c - 1 Error(s), 2 Warning(s).

[@antoniosanmartin5462]

Could you help me find a recorder for a microcontroller of the 8051 family, the AT80C5115 from Atmel. Thank you so much. All the best

[@michaelboss7968]

OH THE MUSIC IS SO OUTSTANDING , I AM SO LUCKY TO GET A CHANCE OF HEARING THIS WONDERFUL MUSIC WOW THANK YOU SO MUCH.

[@hobbyelectronics2121]

My Pleasure

[@francorota9099]

hi, very interesting proyect. The 8051 SPI Programmer doesn't "Identify" my AT89S52, I can only use Port COM 3. Any help?

[@hobbyelectronics2121]

You must have to check your connections and the port on which the programmer is attached.

[@francorota9099]

I tried conecting the optional resistor and capacitor as sugested. Trying to follow the connections you made in minute 1:54, I connected the capacitor with - polarity and ressitor with the pin 9 of the IC and the + polarity of the capacitor with the pin 30 of the IC(think is the ALE/PROG pin), the pin 30 is also connected with pin 39?the optional resistor connected to ground.

[@hobbyelectronics2121]

@@francorota9099 When I made it first time I got the same problem.But it was resolved when I recheck my connections.90% problem is on the connections and 10% goes with the program.You should check the correct port and must check the power supply Its possible that there is a problem in the power supply you provided.You must follow the diagram I given in the description the capacitor and the resistor are optional they are or not required.I hope this will help you.

[@RANAALI-xf5dj]

Arduino ki pin 2-3-4-5 use krni hai ya 1-2-3-4??????

[@hobbyelectronics2121]

pin 5, 4,3 and 2 of arduino uno are used in this project they are connected to MOSI, MISO, SCK and RST respectively of the AT89S52

[@AdityaSinghania]

Can i replace AT89C51 with AT89S51 if i don't have programmer for AT89C51. Also , will the code and circuit change for the project I am making if i exchange these microcontroller

[@hobbyelectronics2121]

No, you can't replace AT89S52 with AT89C51, while programming it with an ISP programmer (arduino in this case). AT89C51 is programmed using Flash programming technique, while, AT89S52 has an inbuilt ISP protocol so it can be straightforwardly programmed using an ISP programmer. Hope it helps! :)

[@AdityaSinghania]

@@hobbyelectronics2121 Okay. But can I use At89S51 in place of At89c51 for my project which is 8 player quiz buzzer?

[@AdityaSinghania]

I will program At89s51 with isp programmer. I just want to confirm will the keil code and the circuit for my 8 player quiz buzzer remain same for both the microcontroller, that is c51 and s51?

[@AdityaSinghania]

Please reply

[@hobbyelectronics2121]

@@AdityaSinghania They will, because both the micrcontrollers have the same pin configuration and architecture. There's a trivial difference between them, but both are a best fit for each other's applications. Hope it will sought out your problem.

[@surya.6283]

I tried checking every connection...I cross checked everything many many times...ports...program...still chip is not detected by the programmer...help plzzz.

[@hobbyelectronics2121]

If the connections are right.Then make sure that the right arduino com port is selected and the program is uploaded correctly to the arduino.

[@surya.6283]

@@hobbyelectronics2121 yes man I did. Still I am not getting where it went wrong. I even kept led at the connection to make sure there is no loose contacts. I made connection arrangements as good as possible to understand and neat. it use to work before and used LCD too....but suddenly it stopped working. So I even changed microcontroller. And also checked port pins of Arduino. Plz help me somehow man...

[@hobbyelectronics2121]

This programmer is for AT89S52.Make sure you that have the right 8051 chip if you have then the problem might be with the power supply.Hope this will help you.

[@surya.6283]

@@hobbyelectronics2121 ok I will check again.

[@surya.6283]

@@hobbyelectronics2121 any more suggestions?. I am using multimeter to check voltage of VCC. 4.66v is being provided to vcc pin of microcontroller by Arduino.

[@p0intblank597]

Can i program AT89C51 with same process

[@hobbyelectronics2121]

No you can't. AT89S series microcontrollers support ISP but AT89C series microcontroller didn't. You can only program ISP(AT89S series) microcontrollers with the arduino.

[@p0intblank597]

So how shall I program my AT89C51..... Please leave a link for video or tell me how to program it.

[@hobbyelectronics2121]

here is the diagram of the programmer drive.google.com/file/d/1IXsHdnBetkYfhR37jftExzieDqKmyBBq/view?usp=sharing.I hope this will help you.

[@sudhiracharya1234]

89C51 required ISP programming or parallel pgm. 89PV51 can flash via serial communication Usb to uarr (max232). 89 C51 serial communication flash via SPI

[@babyph65]

give the keil project too or atleast show how to do it

[@JigneshPatel-tz8dl]

Sir aap ka project acha hai ....lekin details me samjaiye .. please

[@hobbyelectronics2121]

Okay bro later in the future

[@preetamsahoo9430]

everything is alright but led not blinking. All ports are giving only high output.

[@mohamedalaa98]

The Same With Me .. any solution !?

[@preetamsahoo9430]

@@mohamedalaa98 all ports must be set to 0 in main function.

[@preetamsahoo9430]

@@mohamedalaa98 yes

[@surya.6283]

same problem...help me too. how to set all ports to 0?

[@mohamedalaa98]

I think all port set to give 0 and i feed with 5v

[@MubinBro]

Whether it work for at89c51?

[@hobbyelectronics2121]

No, AT89C series don't have ISP but AT89S series have.This is only for ISP AT89S series microntrollers.

[@MubinBro]

can you please help me out for AT89C

[@hobbyelectronics2121]

@@MubinBro here is a link of diagram for the AT89C series microcontroller programmer drive.google.com/file/d/1IXsHdnBetkYfhR37jftExzieDqKmyBBq/view?usp=sharing.I