its been years i have been looking for this information, thank you so much
@ratimus2000 Жыл бұрын
Hi. I presume you had resistors in the led wires, what value please? Thanks.
@gloumer770211 ай бұрын
This method works for engine codes, but not for a flashing airbag light. Any idea how to diagnose the airbag fault code?
@Mawsheng6222 жыл бұрын
感謝!老車真的需要更多的愛來照顧!
@shanerichards23673 жыл бұрын
Great video where do I find the flash codes? What website are you cross referencing the flashes with.
@lalim9233 жыл бұрын
In the description , I just upload it . Hope its help. www.mediafire.com/file/d9v9zcm55blrsik/Mazda_OBD1_Diagnostic_Code.doc/file
@shanerichards23673 жыл бұрын
@@lalim923 yes it worked but mine is throwing out a code of (21 16 ) 2002 Mazda 323. On the list there is no 21 or 16 . Is my car throwing out a 4 digit code?
@lalim9233 жыл бұрын
4 digit code only can decoded by using handheld scanner , the 2 digit code is correct but for the code 21 not available in the Mazda OBD1 engine code library. Code = Memory = Circuit Diagnosed 02 = Yes = 'NE2' crankshaft position sensor 03 = Yes = 'G' camshaft position sensor 04 = Yes = 'NE1' camshaft/crankshaft position sensor 05 = Yes = Knock sensor 08 = Yes = Volume Air Flow sensor (VAF) 09 = Yes = Coolant temperature sensor (CTS) 10 = Yes = Intake air temperature sensor (IAT) 12 = Yes = Throttle position sensor (TPS) 14 = Yes = Barometric pressure sensor 15 = Yes = LHO2S inactivation error 16 = Yes = Exhaust gas recirculation (EGR) system 17 = Yes = LHO2S inversion error 23 = Yes = RHO2S inactivation error 24 = Yes = RHO2S inversion error 25 = Yes = Fuel pressure regulator control solenoid 26 = No = Canister purge solenoid 28 = No = EGR vacuum solenoid 29 = No = EGR vent solenoid 34 = No = Idle air control (IAC) solenoid 41 = No = VRIS #1 solenoid 46 = No = VRIS #2 solenoid 67 = No = LFAN relay (1993 only) 69 = Yes = ECTF sensor (1993 only)
@dapeco597 ай бұрын
El link no tiene virus? @@lalim923
@vincentlee24602 жыл бұрын
I have been looking for these codes for a long time
@oussamarahmani4631 Жыл бұрын
Hi I don’t have TAT pin , how can i diagnostic transmission??
@mariostanko21 Жыл бұрын
Way this dont work in my 323f ba, 1,5.95 yr,? I turnir wire in dijagnostic konektor and led, and no signal. Please help mi. Thanks.
@azbgames68272 жыл бұрын
what kind of connector does a japanese domestic model mazda 626 capella use?
@lalim9232 жыл бұрын
Mostly Mazda 626 using J850bus+, if not work , try Iso9141-2 K-Line
@vincentlee24602 жыл бұрын
How do u erase error codes stored in the computet after the car is fixed?
@lalim9232 жыл бұрын
Removes negative terminal of the car battery. Depressed brake for 10 seconds will reset car ecu including error code.
@vincentlee24602 жыл бұрын
For US MECS-II which pin is the BUS + line and which other pin is the BUS -ve line?
@lalim9232 жыл бұрын
Watch this video kzbin.info/www/bejne/epunZISmoN2JsJo
@vincentlee24602 жыл бұрын
Thank you so much for sharing this knowledge. I'm going to do this mod so make trouble shooting electronic faults so much easier.
@byron1dagg802 жыл бұрын
What about airbag (srs) codes? where can i find the flashes meaning for airbag faults?
@lalim9232 жыл бұрын
Hi, In the description have the code for airbag.
@byron1dagg802 жыл бұрын
@@lalim923 what where in description?
@lalim9232 жыл бұрын
(SRS) Supplemental Restraint System Malfunction codes In order of priority from highest to lowest: - = No air bag lamp: diagnostic monitor (DM), ignition power or bulb circuit - = Continuous lamp: DM disconnected or inoperative 12 = Low battery voltage 13 = Air bag circuit or crash sensor shorted to ground 21 = Safing sensor mounted incorrectly 22 = Safing sensor: output shorted to battery voltage 23 = Safing sensor input feed or return circuit open 24 = Open in circuit 944B or low-resistance in crash sensor(s) 32 = Driver's side air-bag / safing sensor: high resistance or open 33 = Pin 7 not grounded at DM 34 = Driver's side air-bag / safing sensor: low resistance or shorted 35 = Low resistance across pins 8 and 9 of DM 41 = Crash sensor circuit: high resistance or open 44 = RH crash sensor not mounted properly 45 = Center (radiator) crash sensor not mounted properly 46 = LH crash sensor not mounted properly 51 = DM internal fuse: blown and short to ground no longer exists 52 = Backup-power supply: voltage boost fault 53 = Internal DM fault - = Rapid continuous flashing or air-bag lamp: all crash sensors disconnected
@byron1dagg802 жыл бұрын
@@lalim923 thank you so much i really appreciate your work
@byron1dagg802 жыл бұрын
@@lalim923 But what terminals do i short and connect led to, to actually read them?
@jakeboynz Жыл бұрын
Great video... Thankyou!! Did you just make the led tester with just any LED & wires?
@lalim923 Жыл бұрын
Yes, correct
@tomster75742 ай бұрын
@@lalim923 can you use a normal lightbulb from tester?
@alnatural100mejor2Ай бұрын
No es recomndable , porque estarias pasando mucho voltaje al pin de comunicación ( FEN)del Obd1. Puedes usar una lámpara lógica. Y si usas un LED creo que debería colocar una resistencia de 100 Ohmnios en la pata positiva del led para que no termine quemandose. @@tomster7574
@gamboeric7186 Жыл бұрын
Please how can i get the software to read the codes
@lalim923 Жыл бұрын
In the description has the links.
@nunosantos3822 жыл бұрын
Hi, my mazda doesn't have a fen terminal on obd port, can you help me to find the way to connect a led to find de error code? Thanks
@lalim9232 жыл бұрын
Your Mazda 626 car have European (EU MECS-II 1993-2002) Diagnostic Connector, It does not have the FEN pin. Only (US MECS-II 1993-1995) Diagnostic Connector has the FEN pin. You can find the fault code using ELM327 , BUS+ and BUS- is are the communication pins, check out my other video. Mazda OBD1 check engine fault code using ELM327 kzbin.info/www/bejne/epunZISmoN2JsJo
@vincentlee24602 жыл бұрын
My Mazda protege year 2000 is US MECS-II. Strange
@mamanhermawan2014 Жыл бұрын
Saya coba ko led nya gak bisa ngedip ya
@ВиталийЗавирюха-к2ъ2 ай бұрын
Мне этот вариант не подходит, так как у меня другая розпиновка..😢