How to rebuild a stripped and cleaned pit bike carb. remember to subscribe to watch the full build series on the bike. clothing visit d28media.com
Пікірлер: 30
@psychopathblxx2 жыл бұрын
please settings for 140cc engine
@bmw722218 күн бұрын
hey did your air screw come with an o ring with it?
@kkos Жыл бұрын
Great video. I did ultrasonic cleaning for carb and found little brass ball after. Look like it is check valve. Don't know where put it back. Can you help?
@иваниванов-ф2б5х2 жыл бұрын
Well, you showed! How are you going to connect the cable?🧐😉
@elias-nf8qj4 жыл бұрын
Where can i find main jets for this carb?
@спутник-у6у Жыл бұрын
How do i usd the choke on this carbu?
@Giblet16 Жыл бұрын
No wonder I'm getting a massive air leak with mine I didn't know the 2 orings go against each other
@nickcompton47723 жыл бұрын
how far from “seated” should the air screw be and the idle screw ??!
@niiloruotsalainen34283 жыл бұрын
air screw 1,5 rounds and idle start from like maybe 3 and then set it so it idles nice
@abdulsaleh86244 жыл бұрын
i have question; is this molkt carb use mikuni hex mainjets.. is it the pilotjets same with vm26?
@corlyscrawlies2 жыл бұрын
i want to know this.. that pilot jet in the video looks tiny, the main is a hex jet but thr pilot is the short one.. i thought it was a longer type
@sproscoe5 жыл бұрын
What’s the first screw that you screwed in? I have the same carb & when I was cleaning it, it broke from the other piece.
@Moto-li9or5 жыл бұрын
Hi there, by first screw if you mean the very first thing I fitted this was the main jet. if you have the main housing and inside it a jet. these can be purchased if broken. has it broken off and stuck in the body of the carb. we are UK based you are more than welcome to emial me and you can post it over and I will repair and rebuild for you dan@moto28.co.uk
@sproscoe5 жыл бұрын
Moto 28 yes the main jet. It didn’t get stuck I just need the top piece. I can take a picture if you can help me find the piece I need that would be awesome
@Moto-li9or5 жыл бұрын
@@sproscoe yeah no worries, email me one over and I will take a look for you.
@sproscoe5 жыл бұрын
Moto 28 did you get the email?
@Moto-li9or5 жыл бұрын
@@sproscoe I did, I have replied. Also never seen one break like that before.
@pittyrider39035 жыл бұрын
How the hell did you get the pilot jet out ? Iv had 2 of theae carbs and cant get pilot jet out it hust wont turn ends up rounding head off i hav to keep buying new carb?
@Moto-li9or5 жыл бұрын
They should come out fairly easily. Try some mild heat first, make sure it's free from fuel and dry before using a head gun. Possibly some wd40.
@pittyrider39035 жыл бұрын
Ok thanks mate ill give it a try cheers👌
@goftm40584 жыл бұрын
how big is the main jet on this carb?
@Connor-w9y8 ай бұрын
102 I think
@ola-ff6uz Жыл бұрын
Molkt 26 mm Jet Settings YX 150cc ? Original not ok jet -ing Bluurrr VM 22 is ok original
@benkalinowski58345 жыл бұрын
I have it What is the float height
@Moto-li9or5 жыл бұрын
I set the float height level with the carb body.
@benkalinowski58345 жыл бұрын
@@Moto-li9or that's what I thought to Ok ty Just no manual