How to rebuild/repair any Kubota diesel engine Part 1 disassembly

  Рет қаралды 29,703

Rowow

Rowow

Күн бұрын

Пікірлер: 56
@Rowow
@Rowow Жыл бұрын
Thanks everyone for the comment and views. I already put the engine together and it's running great, I have a short I uploaded a while ago of it running. Got the footage recorded but been busy with stuff around the farm to edit it. Sorry for the delay of part 2!
@rapiddave9313
@rapiddave9313 Жыл бұрын
This video was awesome! Cant wait for the assembly and the injector pump videos!
@Rowow
@Rowow Жыл бұрын
Soon. Always busy with stuff sadly. Already got it recorded just need to edit
@Rowow
@Rowow 10 ай бұрын
@@Rowow Second part up! More to come soon.
@joebutler4417
@joebutler4417 Жыл бұрын
Hey Rowow, I appreciate your video man! I am in the middle of doing a complete rebuild of a Universal M5411, which is a marinized Kubota, 2 cylinder, z500 but your video is applicable. Looking forward to part 2. - thanks again.
@Rowow
@Rowow Жыл бұрын
Thanks ill work on the part 2 video this weekend to finish it up. Glad to see interest and hopefully it can help many others
@Rowow
@Rowow 10 ай бұрын
Second part up! More to come soon.
@cornenho
@cornenho Жыл бұрын
Looking forward to see the assembling🎉. Greetz from Holland!
@thefordmann
@thefordmann 11 ай бұрын
did you install the piston sleeves? do you know if the engine can be bored out 0.5mm or do you just have to install the sleeves?
@Rowow
@Rowow 11 ай бұрын
I only replaced the pistons since mines is in perfect tolerance. But yes they have a oversized kit available. In my opinion if you are going to get a bore job done might as well replace the sleeves
@jewtubetruckers
@jewtubetruckers 2 ай бұрын
Hey great video question the overhaul kit you bought did it come with the gaskets for the oil pump and alternator side
@Rowow
@Rowow 2 ай бұрын
Yes but some don't. It's a hit or miss sometimes. Imo just use silicone if they don't. Works better anyways
@jewtubetruckers
@jewtubetruckers 2 ай бұрын
Thanks man red rtv silicone is geat to use ​@Rowow
@markm0000
@markm0000 Жыл бұрын
Great project man I want to see this engine run!
@Rowow
@Rowow Жыл бұрын
I have a short of it running I just need to finish editing up the video of putting it back together
@luisromo5888
@luisromo5888 Жыл бұрын
I am looking forward to seeing the next videos.
@Rowow
@Rowow Жыл бұрын
thanks sorry for the delay, was out of the country and just got back recently. Gonna work on it soon
@Rowow
@Rowow 10 ай бұрын
Second part up! More to come soon.
@damirivancic4964
@damirivancic4964 Жыл бұрын
is this good engine? i always must warm him to easier starting in my digger hitachi?
@Rowow
@Rowow Жыл бұрын
I have a short/vidro of it running. Very good easy to start. I'll make a video on putting it back together next month.
@damirivancic4964
@damirivancic4964 Жыл бұрын
@@Rowow without pusch heating? never? in cold winter?
@Rowow
@Rowow Жыл бұрын
@@damirivancic4964 idk I'm in Florida.
@pete-g8c
@pete-g8c 9 ай бұрын
Thanks for making this vid. I'm in the process of doing the same thing and this is very helpful
@wd2699
@wd2699 9 ай бұрын
Are the orange seals and the washers you remove suppose to be rubber materials?
@Rowow
@Rowow 9 ай бұрын
Which part of the video?
@wd2699
@wd2699 9 ай бұрын
​@@Rowow around 24:00.
@Rowow
@Rowow 9 ай бұрын
@@wd2699 yes those are o rings
@urbansimoncic8623
@urbansimoncic8623 10 ай бұрын
Are these rebuilt kits on eBay good quality? Are all the same or should take care of something?
@Rowow
@Rowow 10 ай бұрын
The 3 ive gotten have all been amazing. Maybe missing some gaskets but otherwise great.
@stuartthompson3837
@stuartthompson3837 9 ай бұрын
I need a crankshaft for a d905. Do you have any recommendations on where to find a good used crankshaft
@Rowow
@Rowow 9 ай бұрын
simply google "D905 crankshaft" lots of brand new ones for $550 dont go with used. Spend a little extra and get a good brand new one
@geraldhenderson4365
@geraldhenderson4365 Жыл бұрын
Great video!!! Can’t wait to see the assembly!!! Question: is it worth learning how to rebuild these? I have 4 Reefer trailers that use these type of engines. I’ve been thinking about learning how to rebuild them.
@Rowow
@Rowow Жыл бұрын
Already got it assembled and ran it works great. Uploaded the short just need to edit the video together on assembly. But yes its definetly worth rebuilding these. Its to cheap and simple. Biggest "issue" is getting the timing on it right. But with kubota's its alot easier than other type of engine timing system and almost impossible to mess up
@markm0000
@markm0000 Жыл бұрын
You can get a spare engine then rebuild it. Whenever a trailer has a bad engine swap it out and rebuild the old one. Meanwhile it can operate as an air compressor and generator for your shop.
@Rowow
@Rowow 10 ай бұрын
Second part up! More to come soon.
@glennsepelak5113
@glennsepelak5113 6 ай бұрын
heating things and little sticks?
@Rowow
@Rowow 6 ай бұрын
I think you mean the glow plugs and push rods
@darryllong484
@darryllong484 7 ай бұрын
Thanks for the video, Question for you or anyone. Do you know what would cause this. I bought a 2006 Kubota M4900 with only 468 hours. I think the hours are right as all of the linkages and pedals are like new. It has a tick in the engine if it is setting down hill a little, hot or cold. You can move it slightly up hill and it will stop ticking and sounds great. You can also take the loader bucket and raise the front slightly above level and it will quit until you let it back down below level. It is not the hydraulic pump, it is in the engine. I have changed the oil and filter twice. I added oil treatment, I adjusted the valves twice. I have put 200 hours on it and it hasn't improved. It's like when you raise the front end a little it moves the oil to the rear of the engine and stops the ticking. I suspect someone has worked on the engine for some reason and maybe left something out that may deflect the oil from going to the front of the engine too far. Does anyone have any suggestions? Thanks very much. Looking forward for a reply.
@Rowow
@Rowow 7 ай бұрын
I really doubt its actually from the engine. I suggest buying a automotive Stethoscope. They sell it at harbor freight, auto zone, amazon, etc. and probing around the engine to figure out exactly where its coming from. Most likely something is hitting against the fan is my guess. Ive seen some really random/unpredictable things to cause stuff like that.
@wb5352
@wb5352 Жыл бұрын
Little sticks are pushrods.
@EwanSadie1
@EwanSadie1 9 ай бұрын
Where did you ever the kit from?
@Rowow
@Rowow 9 ай бұрын
Ebay
@mcl237
@mcl237 8 ай бұрын
Do you sell D1005 rebuilt motors? I have a core if so.
@Rowow
@Rowow 8 ай бұрын
I dont. They are really easy to fix up as you see though.
@mcl237
@mcl237 8 ай бұрын
@@Rowow I’ll ship you mine and rebuild it then lol.
@quique323
@quique323 Жыл бұрын
I work on the V2203 everyday
@quique323
@quique323 Жыл бұрын
I service and repair genset units that have these engines. The engines could only be used a maximum of 7 years per California emissions
@YooooouKnowwwww
@YooooouKnowwwww 11 ай бұрын
awesome!!!!
@DDDoesIt
@DDDoesIt Жыл бұрын
Hey my brother, been waiting on more videos. Love your content and personality. When can we expect more videos? Just curious.
@Rowow
@Rowow Жыл бұрын
soon!!! been very busy back from my trip in the philippines. Finally catching up on some things.
@Rowow
@Rowow 10 ай бұрын
Second part up! More to come soon.
@juana.damiantarazona7507
@juana.damiantarazona7507 10 ай бұрын
Voy hacer mantenimiento el tanque de combustible, primero tengo que sacar el motor y de allí el tanque, pero , tengo un problema, el tanque está como si faltará sacar algo, me podrán decir que más me falta, los agradeceré siempre, gracias.
@Rowow
@Rowow 10 ай бұрын
Sorry I dont understand
@victorbautista9860
@victorbautista9860 9 ай бұрын
Blahblahblah blahblahblahblah stop talking
@Rowow
@Rowow 9 ай бұрын
its a tutorial video. Could you suggest which parts I could do better in. Some parts I did talk alot as I was working in the florida summer sweating and tired to think how to talk shortly
How to Rebuild a Kubota D1105 T: The Complete Guide Part 1
51:25
KED Farm Repairs
Рет қаралды 35 М.
Buying and refurbishing an old Japanese tractor
41:24
BradenBuildz
Рет қаралды 334 М.
Kubota D902
4:38
Mahesh Gopinath
Рет қаралды 514
engine flush with diesel
23:48
Parts shooter
Рет қаралды 205 М.
【kubota_D1105_diesel engine】assemble the kubta diesel engine
12:16
Cố gắng lên.
Рет қаралды 19 М.
This Kubota Was Nearly TRASHED By A DROPPED Valve Seat!
25:56
Jim's Automotive Machine Shop, Inc.
Рет қаралды 291 М.
Fixed: Kubota D722 diesel engine runaway
15:36
Raincoast Diesel
Рет қаралды 13 М.