HOW TO REDUCE FUEL CONSUMPTION ON GENERATORS

[@kingucheventure5321]

Thanks boss...u re a great teacher oooo...I have been using 2liter of petrol for 4hours now...love u

[@valentinojason9727]

You're a lifesaver..😅 Thank you my guy..🙌🏽

[@jeansambou9053]

Thank you very much. I had this issu juste Yesterday. I follow this instruction. God bless you

[@pandemicmechanic8776]

Turning the air screw loose will feed more air to the engine. This will make your engine leaner. Right, it makes you consume less fuel but it will make your engine hotter which may cause engine failure.

[@samueladitya1729]

can't we just add more cooling fan to the engine then?

[@lard1892]

Yea why not

[@GPforexacademy]

We sincerely apologise to the general public for this very act of nuisance. The poster is one of our psychiatric patients who escape last night. We urge the public to go about their various business as everything is under control. Thanks for your understanding​@@samueladitya1729

[@ibrahemkadhum1180]

The air screw? Is it the black plastic ! Or the iron ?

[@bitrusamos285]

Tnx alot sir I appreciate

[@krishnatalk123]

Very useful

[@thegeniusdjwhizy_entertainment]

Whats the function of the carburetor power?

[@jessjoeking]

He is correct that running lean will burn less fuel. What he is not speaking about, is how the engine will run hotter. More heat will equate to less engine life due to premature wear and/or failure of piston rings and valves. These engines are air cooled. They are set to run optimally for reliability and longevity in balance with fuel consumption and maintenance costs. Running lean will cost less in fuel, but more in wear & tear of the engine. I'd highly recommend that you do not follow this advice.

[@docfarl]

The fuel you save in one or two weeks will more than buy and install a new piston and rings. Over a longer term, that fuel savings can even buy a new generator! So, doing something to save fuel makes sense.

[@LAWALYRICS]

@@docfarlthere’s nothing bad in saving fuel if there’s no side effect but if there’s it doesn’t worth it at all, cuz once you start some issues with your gen😂 sope Otilo

[@kabirraji7341]

God bless you man ...video was really helpful

[@ogenyisilas6387]

Are you sure it can reduce fual

[@matix250]

Can the engine be running while I set the cab?

[@freshestworksproduction5144]

Pls What's the use of the black screw there after the carburetor screw?

[@ajiboyegbengs3074]

To increase the power

[@nathanielstuckey3354]

That is the idle screw

[@nathanielstuckey3354]

The one with spring on it is your air fuel ratio

[@nathanielstuckey3354]

You can't just make a engine use less fuel you have to give these small engines the amount they need turning the engine use your ear to tune if you don't have a tech guage

[@nathanielstuckey3354]

Air fuel screw is 1 and half. To. 2 turns is normal

[@spencerobodago4619]

Is there no side effects

[@ff.phenom1593]

Thanks boss

[@lard1892]

Just what I need ....adding problems to a small gas engine.

[@sammysammy7723]

Good job. But are you really sure it has no side effect?

[@GuardianApe]

Will this not affect rpm ?

[@robertkubrick3738]

Could make it run faster, leaning out the engine. When a piston engine aircraft takes off, they lean out the engine to get maximum power then trim the fuel at altitude after they take off...in old planes anyway.

[@docfarl]

The rpm is controlled by the Governor, which is inside the engine, but connected to the throttle with a small rod and spring.

[@anselmifedi]

I love this

[@charlesvardon6731]

Thanks

[@olaoyewinner8143]

Thank you oooooooo

[@Mr.warthog_v16COIN]

Why can’t you just go straight to the point? Who no sabi say na carburetor Dey distribute fuel to the engine🤦

[@brucehurst2199]

It will burn the engine s vales.because it is to lean

[@docfarl]

Engine valves don't burn! Piston rings will wear faster if the engine runs hotter.

[@kennethcain3803]

I cannot understand with your dialect. sorry for trying

[@freshestworksproduction5144]

Turn on captions

[@ibrahemkadhum1180]

So I am 😢 ..I didn't understand any thing..talking toomuch 😊

[@fashinasamson3759]

Hope it works perfectly 😊

[@Starkcreations99]

E don't work 🤣🤣